Scribd
Upload
205 views

Lecture # 7

The document provides information about soil permeability and seepage, including definitions of key terms like hydraulic gradient and Darcy's law. It describes methods to determine the hydraulic conductivity (k) value, including constant head permeability tests and falling head permeability tests. Laboratory and field methods are discussed. Equations to calculate k using test data like flow rate, head loss, sample size, and test duration are presented.

Uploaded by

naveedsidhu
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
205 views

Lecture # 7

The document provides information about soil permeability and seepage, including definitions of key terms like hydraulic gradient and Darcy's law. It describes methods to determine the hydraulic conductivity (k) value, including constant head permeability tests and falling head permeability tests. Laboratory and field methods are discussed. Equations to calculate k using test data like flow rate, head loss, sample size, and test duration are presented.

Uploaded by

naveedsidhu
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
You are on page 1/ 27

Geotechnical Engineering I

Soil Permeability & Seepage Lecture # 7


(Geotechnical Engineering by V. N. S. Murthy) Engr. Muhammad Awais Shafique Department of Transportation Engineering & Management University of Engineering & Technology, Lahore
1

Soil Permeability
A material is permeable if it contains continuous voids. All materials such as rocks, concrete, soils etc. are permeable. The flow of water through all of them obeys approximately the same laws.

Hydraulic Gradient
When water flows through a saturated soil mass there is certain resistance for the flow because of the presence of solid matter. However, the laws of fluid mechanics which are applicable for the flow of fluids through pipes are also applicable to flow of water through soils.

Hydraulic Gradient
As per Bernoulli's equation, the total head at any point in water under steady flow condition may be expressed as Total head = pressure head + velocity head + elevation head

Hydraulic Gradient
This principle can be understood with regards to the flow of water through a sample of soil of length L and cross-sectional area A as shown in Figure.

Hydraulic Gradient

Hydraulic Gradient
The heads of water at points A and B as the water flows from A to B are given as follows (with respect to a datum)

Hydraulic Gradient
As the water flows from A to B, there is an energy loss which is represented by the difference in the total heads HA and HB.

Hydraulic Gradient
For all practical purposes the velocity head is a small quantity and may be neglected. The loss of head of h units is effected as the water flows from A to B. The loss of head per unit length of flow may be expressed as

Where is called the hydraulic gradient


9

Darcys Law
Darcy in 1856 derived an empirical formula for the behavior of flow through saturated soils. He found that the quantity of water q per sec flowing through a cross-sectional area of soil under hydraulic gradient can be expressed by the formula

10

Discharge and Seepage velocities

11

Discharge and Seepage velocities


Figure shows a soil sample of length L and cross-sectional area A. The sample is placed in a cylindrical horizontal tube between screens. The tube is connected to two reservoirs R1 and R2 in which the water levels are maintained constant. The difference in head between R1 and R2 is h. This difference in head is responsible for the flow of water.
12

Discharge and Seepage velocities


Since Darcys law assumes no change in the volume of voids and the soil is saturated then, qaa = qbb = qcc If the soil be represented as divided into solid matter and void space, then the area available for the passage of water is only Av. If vs is the velocity of flow in the voids, and v, the average velocity across the section then, we have
13

Discharge and Seepage velocities

14

Methods to determine k
Laboratory methods:
Constant head permeability method Falling head permeability method

Field methods:
Pumping tests Bore hole tests

Indirect Method:
Empirical correlations
15

Constant Head Test


A constant head permeameter consists of a vertical tube of lucite (or any other material) containing a soil sample which is reconstructed or undisturbed as the case may be. The diameter and height of the tube can be of any convenient dimensions. The head and tail water levels are kept constant by overflows. The sample of length L and cross-sectional area A is subjected to a head h which is constant during the progress of a test. A test is performed by allowing water to flow through the sample and measuring the quantity of discharge Q in time t.
16

Constant Head Test

17

Constant Head Test


The value of k can be computed directly from Darcy's law expressed as follows

18

Falling Head Test

19

Falling Head Test


The soil sample is kept in a vertical cylinder of cross-sectional area A. A transparent stand pipe of cross sectional area, a, is attached to the test cylinder. The test cylinder is kept in a container filled with water, the level of which is kept constant by overflows.

20

Falling Head Test


Before the commencement of the test the soil sample is saturated by allowing the water to flow continuously through the sample from the stand pipe. After saturation is complete, the stand pipe is filled with water up to a height of ho and a stop watch is started. Let the initial time be to. The time t1 when the water level drops from ho to h1 is noted.
21

Falling Head Test


The hydraulic conductivity k can be determined on the basis of the drop in head (ho h1) and the elapsed time (to t1) required for the drop as explained below. Let h be the head of water at any time t. Let the head drop by an amount dh in time dt. The quantity of water flowing through the sample in time dt from Darcy's law is
22

Falling Head Test

The quantity of discharge dQ can be expressed as

23

Falling Head Test

24

Question
A constant head permeability test was carried out on a cylindrical sample of sand 4 in. in diameter and 6 in. in height. 10 in3 of water was collected in 1.75 min, under a head of 12 in. Compute the hydraulic conductivity in ft/year and the velocity of flow in ft/sec.

25

Question
A sand sample of 35 cm2 cross sectional area and 20 cm long was tested in a constant head permeameter. Under a head of 60 cm, the discharge was 120 ml in 6 min. The dry weight of sand used for the test was 1120 g, and Gs = 2.68. Determine (a) the hydraulic conductivity in cm/sec, (b) the discharge velocity, and (c) the seepage velocity.
26

Question
Calculate the value of A: of a sample of 2.36 in. height and 7.75 in2 cross-sectional area, if a quantity of water of 26.33 in3 flows down in 10 min under an effective constant head of 15.75 in. On oven drying, the test specimen weighed 1.1 Ib. Assuming Gs = 2.65, calculate the seepage velocity of water during the test

27

You might also like