Scribd
Upload
258 views

Design of Rivets

Rivets are used to make permanent fastenings between metal plates in structures like ships, bridges, and tanks. There are two main types of riveted joints: lap joints, where one plate overlaps another; and butt joints, where plates are aligned with a cover plate riveted on one or both sides. The design of riveted joints must consider failures from plate tearing at edges or across rows of rivets, rivet shearing, or crushing of rivets. Proper pitch, margin, and plate thickness can prevent failure of riveted joints.

Uploaded by

Ravishanker Baliga
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
258 views

Design of Rivets

Rivets are used to make permanent fastenings between metal plates in structures like ships, bridges, and tanks. There are two main types of riveted joints: lap joints, where one plate overlaps another; and butt joints, where plates are aligned with a cover plate riveted on one or both sides. The design of riveted joints must consider failures from plate tearing at edges or across rows of rivets, rivet shearing, or crushing of rivets. Proper pitch, margin, and plate thickness can prevent failure of riveted joints.

Uploaded by

Ravishanker Baliga
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
You are on page 1/ 20

DESIGN OF RIVETED JOINTS

A rivet is a short cylindrical bar with a head integral to it.

The rivets are used to make permanent fastening


between the plates such as in structural work, ship building, bridges, tanks and boiler shells.

Widely used for joining light metals.

Essential Qualities of a Rivet


The material of a rivet must have a tensile strength not less than 40 MPa. Elongation not less than 26 percent. Material must be of such quality that when in cold condition, the shank shall be bent on itself through 180 without cracking and after being heated to 650C and quenched, it must pass the same test. The rivet when hot must flatten without cracking to a diameter 2.5 times the diameter of shank.

Types of Rivet Heads

Types of Riveted Joints


Lap Joint: A lap joint is that in which one plate overlaps the other and the two plates are then riveted together.

Butt Joint: A butt joint is that in which the main plates are kept in alignment touching each other and
a cover plate (i.e. strap) is placed either on one side or on both sides of the main plates. The cover plate is then riveted together with the main plates.

Terms Used in Riveted Joints


Pitch. It is the distance from the centre of one rivet to the centre of the next rivet measured parallel to the seam as shown It is usually denoted by p.

Back pitch. It is the perpendicular distance between the centre lines of the successive rows. It is
usually denoted by pb. Diagonal pitch. It is the distance between the centres of the rivets in adjacent rows of zigzag riveted joint. It is usually denoted by pd. Margin or marginal pitch. It is the distance between the centre of rivet hole to the nearest edge of the plate. It is usually denoted by m.

Failures of a Riveted Joint


Tearing of the plate at an edge : A joint may fail due to tearing of the plate at an edge. This can be avoided by keeping the margin, m = 1.5d, where d is the diameter of the rivet hole.

Tearing of the plate across a row of rivets: Due to the tensile stresses in the main plates, the main plate or cover plates may tear off across a row of rivets.

The resistance offered by the plate against tearing is known as tearing resistance or tearing strength.

Shearing of the rivets: The plates which are connected by the rivets exert tensile stress on the rivets, and if the rivets are unable to resist the stress, they are sheared off.

Crushing of the plate or rivets: Sometimes, the rivets do not actually shear off under the tensile stress, but are crushed.

The rivet hole becomes of an oval shape and hence the joint becomes loose.

You might also like