Air pollution from industrial activities like burning fossil fuels and metal processing has increased significantly. This document discusses various air pollutants like particulate matter, sulfur dioxide, carbon monoxide, and heavy metals that are emitted from industries including foundries. Foundries produce particulate pollution from processes involving melting metals, mold preparation, and finishing operations. Emissions can contain toxic metals and average around 10 kg of dust per ton of molten metal processed. Other wastes from foundries include slag, wastewater, and spent sand molds. Control of air and water pollution is important to reduce health and environmental impacts.
Download as PPTX, PDF, TXT or read online on Scribd
100%(2)100% found this document useful (2 votes)
1K views
Pollution Control in Foundries
Air pollution from industrial activities like burning fossil fuels and metal processing has increased significantly. This document discusses various air pollutants like particulate matter, sulfur dioxide, carbon monoxide, and heavy metals that are emitted from industries including foundries. Foundries produce particulate pollution from processes involving melting metals, mold preparation, and finishing operations. Emissions can contain toxic metals and average around 10 kg of dust per ton of molten metal processed. Other wastes from foundries include slag, wastewater, and spent sand molds. Control of air and water pollution is important to reduce health and environmental impacts.
Download as PPTX, PDF, TXT or read online on Scribd
You are on page 1/ 13
POLLUTION CONTROL IN FOUNDRIES
Dr. M K Jain & Suresh Kumar
AIR POLLUTION
Air pollution occurs due to increased industrialisation and urbanisation in addition to natural causes like cyclones, volcanic eruptions. As a result of rapid development of industries, air pollution by waste material, smoke and gases formed by industrial processes has become a problem of vital importance. On our planet, nearly 2 Billion tonnes of coal and 1 Billion tonnes of petroleum are burnt every year, which are accompanied by the liberation of about 250 million tonnes of Sulphur Dioxide. Heavy metals like As, Cd, Hg, Pb, Antimony and Bismuth etc, are found alarming in fly ash fall outs (upto 50 to 500 Tonnes/Km 2 /Month) from the 500 MW TPS stack at a distance one to four kms. Airborne Ni-dust and vapours causes cancer of lungs and sinus. Exposure to dust or fumes of tin causes Pneumoconiosis / Stannosis. Arsenic is poisonous in most chemical forms, and same is true with Cd, Cu, Hg, and Pb. Bismuth compounds are absorbed through skin and may cause kidney damage.
MECHANISM OF ACTION OF AIR POLLUTANTS The air we breathe has not only life supporting properties but also life damaging properties. Under ideal conditions the air we inhale has a qualitative and quantitative balance that maintains the well being of man. But when the said balance of its components is disturbed, or in other words, if it is polluted it may affect human health. A healthy man inhales nearly 15-16 Kg air/day. If, this air is polluted, intake of oxygen is reduced. Besides, there are the adverse effects of pollutants on men, animals, vegetation, and materials. The effects of air pollution on human health generally occur as a result of contact between the pollutants and the body. Contact with exposed membrane surfaces is of utmost importance, because of their high absorptive capacity compared to that of the skin. Airborne gases, vapours, fumes, mist and dust may cause irritation of the membranes of the eyes, nose, throat, larynx, tracheo-bronchial tree and lungs.
It is therefore necessary to identify and accurately quantify various pollutants in the air to ascertain the air quality we breath. The major pollutants which pollutes the air are:-
SUSPENDED PARTICULATE MATTER (SPM) are a complete group of substances, liquids or solids, dispersed in the atmosphere, which range in diameter from a fraction of a micron to several hundred microns. The most significant fraction of suspended particulate matter is the respirable size, i.e., larger than about 0.1 microns and smaller than about 5-10 microns. The measuring method may be either based on gravimetric principle or on photometric characteristics of the particulate matter. The gravimetric method involve collection of suspended particulate matter often for a 24 hours period. The mass of particulate matter is determined by weighing filters before and after sampling. For the photometric methods, particles are collected on filters for periods one to 24 hours. In these methods, transmittance or reflectance of the deposited matter is measured. The collected dust may also be analysed to find out its chemical composition. Ambient air is drawn under a fixed-area gabled roof through a filter by means of a heavy duty turbine blower at a constant flow rate ranging between 1.1 and 1.7 cubic meters per minute (m 3 /minute). Suspended particles having diameters (Stokes equivalent diameter) between 0.1 and 100 um are removed from this air stream by filtration on a glass fibre filter. The mass concentration (ug/m 3 ) of suspended particulates in the air is determined by measuring the mass of the collected particulates and dividing the volume of the air sampled. SULPHUR DIOXIDE Sulphur dioxide is a non-flammable, colourless gas that can exist in air either as a gas or dissolved in water droplets. It can be tasted by most people at concentration of about 900 ug/m 3 or greater. Sulphur dioxide partially oxidises in air to for sulphur trioxide (SO 3 ), which readily combines with water vapour to form sulphuric acid (H 2 SO 4 ). +The automated techniques for the continuous measurement of SO 2 in air are especially appropriate for use in air pollution control programs in which a continuous record is a necessity. The principles involved for the more commonly used continuous techniques are conductivity, calorimetric, electro chemical diffusion, and gas chromatography coupled to flame photometry. CARBON MONOXIDE (CO) Carbon monoxide (CO) is one of the most videly distributed and most commonly occurring air pollutants. Atmospheric CO is primarily produced by the incomplete combustion of carbonaceous materials used for vehicles, space heating, and industrial processing. Carbon monoxide is a colourless, odourless, tasteless, stable gas, slightly lighter than air; in high concentrations it can cause many physiological changes and, ultimately, death. Exposure to relatively low levels of CO may result in significant health effects after only a few hours. There are four methods used to determine the concentration of CO as per IS:5182 (Part X)-1976.
(i) Iodine Pentoxide Method The reaction between carbon monoxide and iodine pentoxide at 135 to 150C to yield carbon dioxide and iodine vapour. The concentration of carbon monoxide in the air sample may be determined by analysis of the amount of either carbon dioxide or iodine produced. 5CO + I 2 O 5 = 5 CO 2 + I 2
It is necessary to pass the air sample through an elaborate purification train consisting of activated carbon, an efficient drying agent, a chromic acid wash tower and some solid absorbent to remove carbon dioxide. The dry air is then passed through a U-tube containing iodine pentoxide. Free iodine is liberated according to above reaction if carbon monoxide is present. The iodine liberated in the reaction is absorbed in potassium iodide solution and titrated with standard sodium thiosulphate solution.
(ii)Indicator Tube Method. Carbon monoxide reduces yellow silicomolybdate to lower oxides. The colour changes from yellowish green to green and finally deep blue depending on the extent reduction which again under identical conditions depends on concentration of carbon monoxide in air. Hydrogen sulphide, unsaturated hydrocarbons, moisture,etc, interfere but they may be removed by passing the sample through various absorbents provided with the indicator tubes.
(iii)Non-Dispersive Infrared Absorption Method Samples containing carbon monoxide in the range of 0 to 100 ppm are analysed on a non-dispersive infrared absorption gas analyser, namely, an electro-optical spectrophotometer with no spectral dispersion component. It may consist of a single or double source of infrared energy and one or more infrared detectors separated by an optical cell or cells through one or more which the sample flows, whereby the specific spectral absorption of the component of interest is determined.
(iv)Gas Chromatography Method A sample of air containing carbon monoxide is injected into the gas chromatography where it is carried from one end of the column to the other. During its movement, the constituents of the sample undergo distribution at different rates and ultimately get separated from one another. The separated constituents emerge from the end of the column one after the other and are detected by suitable means whose response is related to the amount of a specific component leaving the column.
POLLUTION IN FOUNDRIES
Molten metals are cast into objects of desired shapes in foundries. The main production steps include: (i) Preparation of raw materials, (ii) Metal melting, (iii) Preparation of molds, (iv) Casting and (v) Finishing (which includes fettling and tumbling)
Castings of iron, steel, light metals, and heavy metals are made in units that may be independent or part of a production line. Auto manufacturing facilities usually have foundries within their production facilities or as ancillaries. Emissions of particulate matter (PM) from the melting and treatment of molten metal, as well as from mold manufacture, shakeout, cleaning and after-treatment, is generally of greatest concern. Particulate matter may contain metals that may be toxic. Major pollutants present in the air emissions include particulates of the order of 1,000 mg/Nm 3 . Generally, foundries produce 10 kg of dust per ton of molten metal, with a range of 5 30 kg/t, depending on scrap quality and other related factors. However, induction furnaces (with emissions of 3 kg/t of molten metal) and flame ovens tend to have lower air emissions than cupolas and electric arc furnaces (EAF). Oil mists are released from the lubrication of metals. Oil and suspended solids are released into process effluents, and treatment is warranted before their discharge. Wet scrubbers release wastewaters that may contain metals. Wastewater from tumbling may contain metals and surfactants. Odor and alcohol vapor (from surface treatment of alcohol-based blacking) and emissions of other volatile organic compounds (VOCs) are also of concern. Sand molding creates large quantities of waste sand. Other wastes include slag (300500 kg/t of metal), collected particulate matter, sludge from separators used in wastewater treatment, and spent oils and chemicals. Discarded refractory lining is another waste produced. The primary hazardous components of collected dust are zinc, lead, and cadmium, but its composition can vary greatly depending on scrap composition and furnace additives. (Nickel and chromium are present when stainless steel scrap is used.) Cooling waters (upto 20 m 3 /t), may contain oil and some chemicals for the control of algae and corrosion. Foundries can generate up to 20 m 3 of wastewater per metric ton of molten metal when cooling water, scrubber water, and process water are not regulated. Untreated wastewaters may contain high levels of total suspended solids, copper (0.9 mg/l), lead (2.5 mg/l), total chromium (2.5 mg/l), hexavalent chromium, nickel (0.25 mg/l), and oil and grease. The characteristics of the wastewater will depend on the type of metal and the quality of scrap used as feed to the process. Solid wastes (excluding dust) are generated at a rate of 300500 kg/t of molten metal. Sludge and scale may contain heavy metals such as chromium, lead, and nickel. Air Pollution control Systems (APCS) Different air pollution control systems, which may be adopted in foundries are: (1) Furnace Fume Extraction & Filtration System (FES) (2) Scrubber (Wet Type) & Bag Filter (Dry Type) (3) Dust Collection system for Knock Out Plant (4) Dust Collection system for Sand Reclamation Plant (5) Dust Collection system for Shot Blasting & Sand Blasting (6) Dust Collection System for Thermal Sand Reclamation Plants with air to air heat exchangers (7) Sand Unloading Stations with Dust Collection System (8) Dust Collection Systems for Material Handling Points viz., Bucket Elevator, Belt Conveyer, Screens, Mixing Plants (9) FD Centrifugal Blowers for Cupola Furnaces (10) Pneumatic Sand Transporters, Wear Resistance Bend (11) Vent Dust Collectors for Storage Silo (12) Welding Fume Extractors / Central Fume Extraction for Weld Shop (13) Fettling Booth with Dust Collector