Public Switched

Telephone Network (PSTN II/II)

2
Topics today in PSTN

A: Switching types
Connectionless/ connection oriented
Packet/circuit
B: PSNT exchanges and interfaces
interface Q.512
using access and trunk networks
signaling
network management
internetworking (telecommunications between networks)

Node 1 Node 2
Node 3
Access
Trunk Network
Terminals Terminals
Access
3
Switching in public networks
CSPDN: Circuit switched public data net*
PSPDN: Packet switched public data net**
DQDB: Distributed queue dual bus
* Used by European Telecoms that use X.21 in circuit switched nets
**Used by British Telecoms Packet-switched Service (PSS), Data Pac (Canada) ...
(fixed
length)
Cell switching
- resembles packet switching
- difference: cells (packets) have a fixed size :
offers bounded delay guarantees
(QoS compatible, long packets wont stuck cells)
4
Circuit switching
Time switch
- Makes switching between time slots
- In the figure incoming slot 3 is moved to
outgoing slot 3 for one voice direction
- Each coming timeslot stored in Speech Store (SS)
- Control store (CS) determines the order the slot
are read from SS
- The info in CS is determined during setup
phase of the call
Space switch
- makes switching between PCM lines
- works with electronic gates controlled by CS Cross-point
controlled
by CS
Circuit switching
- dedicated path
- constant delay/bandwidth
- voice/data
- paid by time
- examples: PSTN, VPN
TDMA
5
Packet switching
Node structure
Packet structure
Seq: sequence number
Op code: message/control
identifier
CRC: Cyclic Redundancy
Code
Note:
- source address
required for retransmission
in ARQ
- byte count could be also an
end flag
6
Connection-oriented and connectionless
switching
Connection oriented
- Applies same route
- QoS well defined
- Phases
- Connection setup
- Data transmission
- Release
- Packets received in same order
- Example: ATM, frame relay, PCM
Connectionless
- Use of different routes for
each packet possible
- Each packet have address fields
- QoS not guaranteed
- Packets may come in different order
- Example: IP (Internet Protocol),
TCP takes care of cleaning the mess
7
Transfer modes & connections summarized
Circuit switching
Packet switching
Connection oriented
Connectionless
- hand-shaking
- strict error requirements
- for fast data transfer
- broadcasting
- modest error rates
often accepted
- fast data in good channels
Transfer modes Connection types
- developed for data
- nowadays also for voice
- Statistical multiplexing
- variable delays
- developed for voice
- nowadays also for data
- well-specified delays
- echo problems
PSTN
ISDN
PCM
IP, Frame-relay
ATM
X.25
ATM
Frame-relay
IP, UDP*
*User Datagram Protocol
8
Example of cell switching:
Distributed queue dual buss (DQDB)
LAN
access
unit
access
unit
access
unit
LAN
access
unit
Function
- transport units constant length
- access units access
info in the ring:
- know subscribers in access units
subnets and route packets for them
- access protocol applies token ring
Properties
- distributed switching (Compare
to FDDI*)
- ATM compatible
- rates: 64 kb/s ... 45 Mb/s
- geographical limit up to 200 km

*FDDI: Fiber Distributed Data Interface
see: http://www.iol.unh.edu/training/fddi/htmls/
Transport Unit (same as in ATM)
9
Connecting into PSTN exchange:
Equipment in the access network
ISDN connection
example: 30B+D
(2.048 Mb/s)
Twisted pair - connection
Private Branch Exchange
Multiplexer
On-line subscriber
with several telephones
Business
subscriber
Wireless
access
(or radio access
point)
Distribution point
Cross connection point
ISDN 2B+D
144 kb/s
Q.512 specifies
exchange interfaces
10
S
w
i
t
c
h

Local exchange
Subscriber
stage
Group
switch
ETC
Announcement
equipment
Signaling
equipment
Test/measure-
ment equipment
Control system
to other exchanges
Third-party
equipment
PBX
ETC: Exchange terminal circuit
IN: Intelligent network
conference calls, call waiting,
broadcasting ...
Signaling (SS7) with users and
other exchanges
Traffic concentration
- Operation & maintenance support (Q.513)
- Charging
- Supplementary (IN) services
- Subscriber data, switch control
C
o
n
t
r
o
l

11
Subscriber stage
T
o


E
T
C

ETC: Exchange terminal circuit
Speech store: shift registers storing bits for time switching
Control store: gates guiding speech store switches
Connects to: digit receivers, info
tones, test equipment
Control System: subscriber
authentication, routing, billing, O & M, ...
Concentrator
internet access
(DSLAM)
centrex service
MUX
12
Exchange control functions
Maintenance functions
supervision of subscriber lines and trunk circuits
Operational functions
administrative data as
subscriber database
routing database
statistical data as
from where and whom subscribers call
holding times for different equipment types
utilization of IN services
User services
Sample of IN services
13
Exchange user services (examples)

Absent-subscriber services as the answering
machine
Call booking: connection at the desired time
Person-to-person call: ensures that call goes to a
right person
Serial call: setting up several calls
Telephone conferencing: several persons
participate to call in real-time (compare: tele-
conferencing)
Directory inquiries: also speech recognition,
recorded messages

(many of these nowadays available in terminals)
14
The space-switch (used as a cross-switch and concentrator)
Number of cross-connections reduced compared if a simple space
division matrix of NxM (input x output) would be used
Usually performs concentration: Blocking possible
Same signal can be routed via different paths: increased reliability
15
The time-switch
One of the time slots of any full-duplex lines is connected to
some other line (at a time)
Thus two switches / time slot connect a line
For 100 full-duplex lines at 19.6 kbps a 1.92 Mbps bus is thus
required for no blocking
If no fixed assignment of input lines to time slot but on demand
allocation -> blocking switch that reduces number of switches
and switch clock frequency. For instance 200 lines of 19.6 kbps
with bus of 1.92 Mbps
-> about half of the devices can connect at any time, eg
concentration is 2:1
16
The time-space-time (TST) switch
Works in local exchange and subscriber stage
Performs PCM concentration, usually 10:1 3:1
Connects subscribers also to information tones
and test equipment
Time switch contains one bus for incoming and outgoing
calls (full-duplex)
Question: Why time or
space switch is not always enough?
S
u
b
s
c
r
i
b
e
r

s
t
a
g
e
Space switch
Time switch
Time switch
17
CN
CN:Concentrator
ET:Exchange T.
LT:Line T.
AN:Access Net.
LT
NT ET
X
ET
ET
ET
LT
LT LT
ET LT
ET LT ISDN PABX
ET LT AN
V1
V2
V3
V5
A
B
NT:Network
T. (in ISDN)
T:Terminal
PSTN ISDN exchange
interfaces (Q.512)
Peek to Q-recommendations
V4
18
Exchange interfaces and tasks, V1
Purpose of exchange is to organizes connection between
exchange terminators!
V1: Access to basic ISDN (This is users ISDN-u interface
that can be used to connect small PBX also)
Basic ISDN V1-functions:
2 B + D (2x64 kbps + 16 kbps) channeling structure
timing and frame synchronization
activate and deactivate terminator
operation and maintenance
feeding power supply
ISDN basic access parameters defined in G.961
19
Exchange interfaces and tasks, V2-V4
V2: Interface serves typically concentrators
2048 kbit/s eg
30 B + D
Electrical standard G.704
V3: Resembles V2 but intended for interface other
exchanges (PABX)
Electrical standard G.703
30 B + D at 2048 kb/s
also 23 B +D at 1544 kb/s (I.431)
V4:Interface to private networks (not ITU-T specified), for
instance DSLAM (ADSL-interface)

20
Exchange interfaces and tasks, V5
Between access network and exchange
2048 kbit/s
Specifies basic interfaces for
Analog access
ISDN-access
Electrical interface G.703
Channel control and signaling
V5 supports interface rates 2048 kbit/s 8448 kbit/s

21
Connecting the local loop:
Line interface circuit (LIC)
Used for signaling in certain
coin-operated pay-phones and PBX
22
Line interface circuit components
Over-voltage protection
Test equipment to connect to monitor the line condition
faults
Voltage feed
ringing
telephone current supply
Detection of
hook stage, pulse generated, or dual-tone receiver
The hybrid junction (2 wire - 4 wire interface)
An A/D converter (uses PCM techniques at 64 kbps)

23
The hybrid circuit
4-wire connection is used between exchanges and 2-wire
connections from exchange to subscribers
Amplifier
Amplifier
Bridge Bridge
Two-wire
Exchange A
Exhange B
Two-wire
24
The hybrid-circuit
If the impedance Z
b
equals the line impedance no
incoming voice (down right) leaks to outgoing voice (up right)
but the signal goes via the two wire connection on the left
To exchange
From exchange
Local loop
25
The hybrid circuit summarized
The hybrid circuit transforms two-wire connection into 4-
wire connection.
If the hybrid is unbalanced echo will result
Hybrid is balanced when no own voice is leaked into
own loudspeaker
Hybrid unbalance can result from line impedance
changes due to weather conditions
Unbalance results echo
Echo cancellation circuits are harmful in data
connections
Nowadays realized by operational amplifier based
circuitry that automatically monitors line impedance
changes

26
Network echo suppressor (NES)
R: transmission gate, A: attenuator, L: logic circuit
When the signal is present on the receiving line the
transmitting line is cut-off








A kind of semi-duplex approach to solve the echo problem
27
Network echo canceller (NEC)
Signal echo is extracted and subtracted from the
received signal
More effective than echo suppressor. Often NEC and NES
are however both used
28
PSTN operation and maintenance
(Q.513)
Different alarm classes
Vital functions and circuits
(as SS7 and group switch)
use secured paths and
backups
Procedures provided for:
troubleshooting
fault diagnostics
hardware faults can
be isolated
Supervision is realized also
by connecting maintenance
units to the network
Important switches have
extensive backup equipment

A supervision plan by
network levels:
29
Modern PSTN hierarchy
to international level
Regional transport level
Local transport level
Access transport level
Local exchange
Transit exchange
30
PSTN Hierarchy cont.
Local (example, within a city)
Subscriber connections
Switching within the local exchange
Switching to other exchanges
Transit (county level, say between Tampere and Helsinki)
Switching traffic between different geographical areas within one
country
International
Gateway-type traffic between
different countries
DWDM (Dense Wavelength Division Multiplexing) routes
Rates can follow SONET or SDH standard
SDH
- transport of 1.5/2/6/34/45/140 Mbps within a transmission rate of 155.52 Mbps
- carries for instance ATM and IP within rates that are integer multiples of 155.52 Mbps
31
Subscriber signaling for local calls
32
Inter-exchange signaling
Channel associated signaling (CAS) as No.5, R1, R2
analog and digital connections
Modern ISDN exchanges apply SS7(digital), that is a
common channel signaling method (CSS) that is
discussed later in its own lecture
CAS is divided into line and register signaling:
Line signaling:
line state between the trunk-links as
answer, clear-forward*, clear-back
Register signaling:
routing information as
B-number, A-category, B-status

*A-subscriber on-hook message transmitted to B exchange
33
Inter exchange signaling (cont.)
Three categories of information is transmitted:
setup, supervision clearing
service related information as
forwarding, callback, charging
status change information
transmission network congestion
neighborhood exchange congestion
34
Example of inter-exchange signaling
35
Inter-exchange signaling (cont.)
36
A case study: DX 200 Exchange
Various control units apply common busses to control the
exchange
SSU PAU CCSU LSU M MFSU DCU
CCMU CM CHU STU OMU
37
A case study: DX 200 Exchange
SSU: Subscriber Signaling Unit: controls access network
CCSU:Common Channel Signaling Unit (SS7).
CCMU: Common Channel Signaling Management Unit: (as
MTP, SCCP)
PAU: Primary Rate Access Unit: controls basic (64 kbit/s)
system interfaces
LSU: Line Signaling Unit: takes care of signaling between
transit exchanges and access networks
MFSU: MULti-frequency Service Unit: Takes care of
signaling when multiple frequency signals are used
MTP: Message transfer part of SS7
SCCP: Signaling connection control part
=SS7 bearer part: network service
part (NSP)

38
A case study: DX 200 Exchange (cont.)
BCDU:Basic Data Communication Unit: Serves various
data services to OMU as access to X.25 and LANs
M: Marker Unit: Controls concentrators / space switches
CM: Central Memory: Contains user database, charging,
signalling, routing and exchange ensemble.
STU: Statistical Unit: Collects statistical information on
traffic and charging.
CHU:Charging Unit: Maintains charging database obtained
from signalling units.
OMU:Operation and Maintenance Unit: Allows personnel
access to exchange memory, perform tests an traffic
measurements.
39