Scribd
Upload
305 views16 pages

Z Source Inverter

This document describes a Z-source inverter, a new type of impedance source power converter. It presents the structure of a traditional voltage source converter for comparison. The Z-source converter employs a unique impedance network coupled to the main converter circuit, allowing it to overcome limitations of traditional voltage and current source converters. It can provide DC to AC, AC to DC, AC to AC, and DC to DC power conversion. The document discusses equivalent circuit modeling, operating principles, control methods, simulation and experimental results, and concludes the Z-source converter provides a novel power conversion concept.

Uploaded by

pradeepagrahari
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
305 views16 pages

Z Source Inverter

This document describes a Z-source inverter, a new type of impedance source power converter. It presents the structure of a traditional voltage source converter for comparison. The Z-source converter employs a unique impedance network coupled to the main converter circuit, allowing it to overcome limitations of traditional voltage and current source converters. It can provide DC to AC, AC to DC, AC to AC, and DC to DC power conversion. The document discusses equivalent circuit modeling, operating principles, control methods, simulation and experimental results, and concludes the Z-source converter provides a novel power conversion concept.

Uploaded by

pradeepagrahari
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
You are on page 1/ 16

Z-Source Inverter

Voltage source inverter

THERE EXIST two traditional converters: voltage-source


(or voltage-fed) and current-source (or current-fed) converters
(or inverters depending on power flow directions). Fig. 1
shows the traditional three-phase voltage-source converter
(abbreviated
as V-source converter) structure. A dc voltage source
supported by a relatively large capacitor feeds the main converter
circuit, a three-phase bridge. The dc voltage source can
be a battery, fuel-cell stack, diode rectifier, and/or capacitor. Six
switches are used in the main circuit; each is traditionally composed
of a power transistor

The ac output voltage has to be greater than the original


dc voltage that feeds the dc inductor or the dc voltage
produced
is always smaller than the ac input voltage. Therefore,
the I-source inverter is a boost inverter for dc-to-ac
power conversion and the I-source converter is a buck
rectifier
(or buck converter) for ac-to-dc power conversion.
For applications where a wide voltage range is desirable,
an additional dcdc buck (or boost) converter is needed.
The additional power conversion stage increases system
cost and lowers efficiency.

Z-SOURCE CONVERTER
To overcome the above problems of the traditional
V-source and I-source converters, this paper presents an
impedance-source (or impedance-fed) power converter
(abbreviated
as Z-source converter) and its control method for
implementing dc-to-ac, ac-to-dc, ac-to-ac, and dc-to-dc power
conversion. Fig. 3 shows the general Z-source converter
structure proposed. It employs a unique impedance network (or
circuit) to couple the converter main circuit to the power source,
load, or another converter, for providing unique features that
cannot be observed in the traditional V- and I-source converters
where a capacitor and inductor are used, respectively.

EQUIVALENT CIRCUIT, OPERATING


PRINCIPLE, AND
CONTROL

All the traditional pulsewidth-modulation (PWM) schemes


can be used to control the Z-source inverter and their theoretical
inputoutput relationships still hold. Fig. 11 shows the traditional
PWM switching sequence based on the triangular carrier
method. In every switching cycle, the two nonshoot-through
zero states are used along with two adjacent active states to
synthesize the desired voltage. When the dc voltage is high
enough to generate the desired ac voltage, the traditional PWM
of Fig. 11 is used. While the dc voltage is not enough to
directly generate a desired output voltage, a modified PWM
with shoot-through zero states will be used as shown in Fig. 12
to boost voltage. It should be noted that each phase leg still
switches on and off once per switching cycle. Without change
the total zero-state time interval, shoot-through zero states
are evenly allocated into each phase. That is, the active states
are unchanged. However, the equivalen

SIMULATION RESULTS, PROTOTYPE,


AND
EXPERIMENTAL RESULTS

CONCLUSIONS

This paper has presented an impedance-source power


converter for implementing dc-to-ac, ac-to-dc, ac-to-ac, and
dc-to-dc power conversion. The Z-source converter employs a
unique impedance network (or circuit) to couple the converter
main circuit to the power source, thus providing unique features
that cannot be observed in the traditional voltage-source and
current-source converters where a capacitor and inductor are
used, respectively. The Z-source converter overcomes the
conceptual and theoretical barriers and limitations of the traditional
voltage-source converter and current-source converter
and provides a novel power conversion concept.

REFERENCES
[1] K. Thorborg, Power Electronics. London, U.K.: Prentice-Hall
International
(U.K.) Ltd., 1988.
[2] M. H. Rashid, Power Electronics, 2nd ed. Englewood Cliffs, NJ: Prentice Hall, 1993.
[3] N. Mohan, W. P. Robbin, and T. Undeland, Power Electronics:
Converters,
Applications, and Design, 2nd ed. New York: Wiley, 1995.
[4] A. M. Trzynadlowski, Introduction to Modern Power Electronics.
New York: Wiley, 1998.
[5] B. K. Bose, Modern Power Electronics and AC Drives. Upper Saddle
River, NJ: Prentice-Hall PTR, 2002.
[6] P. T. Krein, Elements of Power Electronics. London, U.K.: Oxford
Univ. Press, 1998.

Thank
you

You might also like