Scribd
Upload
255 views

CPU Organization / Main Memory

The document discusses the components and organization of the CPU and main memory. It describes the control unit, ALU, and registers that are part of the CPU, including the program counter, memory address, and data registers. It explains that main memory stores programs and data needed for processing and is faster than secondary storage. A bus connects the CPU and main memory, carrying data, addresses, and control signals to facilitate frequent interaction during program execution.

Uploaded by

Vijay Kumar
Copyright
© © All Rights Reserved
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
255 views

CPU Organization / Main Memory

The document discusses the components and organization of the CPU and main memory. It describes the control unit, ALU, and registers that are part of the CPU, including the program counter, memory address, and data registers. It explains that main memory stores programs and data needed for processing and is faster than secondary storage. A bus connects the CPU and main memory, carrying data, addresses, and control signals to facilitate frequent interaction during program execution.

Uploaded by

Vijay Kumar
Copyright
© © All Rights Reserved
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
You are on page 1/ 15

CPU organization / Main Memory

Components of CPU
Control Unit:
Manages and coordinates the operations of all
components of the computer.
Reads instructions, interprets them and generates signals
for appropriate actions.

Arithmetic Logical Unit (ALU):


All calculations and comparison operations are performed
in ALU.
Thus the actual processing of data takes place in ALU.

During the processing of a job, data may move back and forth
several times between primary storage (for intermediate
results and other data) and ALU before processing of the job is
over.
Almost all ALUs are designed to perform four basic arithmetic
operations (add, subtract, multiply, and divide) and logical
operations such as less than, greater than and equal to.

Storage unit
Program
and data

Input
Data

Primary
Storage

Output
Data

Result

Secondary
Storage

Control
Unit

ALU
Central processing unit

Basic functional units of a computer

Data Flow
CPU Control

CPU Registers
As a CPU interprets and executes instructions, there is a
movement of information between various units of the
computer.
To handle this process, and to speed up the information
transfer rate, the CPU uses some special memory units, called
registers.
Registers hold information on a temporary basis and are part
of CPU (not the main memory).
The length of a register is the number of bits it can store.
Length of a register is sometimes also called its word-size.
Most CPUs these days have 32-bit or 64-bit registers.

The number of registers varies from computer to computer.


However, there are some registers common to all computers.
These are described below:

1. Memory Address Register (MAR)


It holds the address of the active memory location.
It is loaded from the program control/counter register when
the system reads an instruction from the memory.
2. Memory Buffer/Data Register (MBR) (or MDR)
It holds the contents of the accessed memory word.
The system transfers an instruction word placed in this
register to instruction register.

A data word placed in this register is accessible for


operation with accumulator register or for transfer to I/O
register.
3. Program Control/Counter Register (PCR)
It holds the contents of the next instruction for execution.
Normally the instructions are executed in a sequential
manner.
4. Accumulator Register (AC)
It holds the data on which the system has to operate,
intermediate results, and results of operations performed.
The system returns the result of an arithmetic operation
to accumulator register for transfer to main memory
through MBR.

5. Instruction Register (IR)


It holds the current instruction under execution.
As soon as the instruction is put in this register, its address
and execution parts are separated. The address part is
sent to MAR and the instruction part is sent to the control
unit for getting decoded.
6. Input/Output Register (I/O)
It is used to communicate with the input/output devices.
All input/output information is transferred through this
register.

Memory
A computers CPU has necessary circuitry for data processing
and controlling other components of the computer.
But is does not have place to store programs and data needed
during data processing.
CPU has several registers for storing data and instructions, but
they can store only a few bytes at a time, sufficient only to
hold one or two instructions.
If the data is stored in the secondary storage, CPU will be idle
most of the time, as there is a great mismatch between the
CPU speed and the rate of transfer of data from the disk to
the computer.
Therefore, every computer has a memory storage, called
primary storage or main memory which reduces this
mismatch significantly.

Instructions and data of a program reside mainly in the main


memory when CPU is executing the program.
Main memory of a computer consists of several small storage
areas called locations or cells.
Each location can store a fixed number of bits called the word
length (or word size) of the memory (usually 16, 32, or 64 bits).
Each location has a built in unique number assigned to it, called
the address of the location.
0
1

N-1

bits

System Bus
A computer stores in the memory the data and instructions of a
program in execution, and fetches and loads them into CPU
registers as the program execution proceeds.
Thus CPU and memory interact frequently. This interaction is
facilitated by a bus.
A bus is a communication pathway connecting two or more
devices of a computer.
Multiple devices connect to the bus, and a signal transmitted by
any device is available for reception by all other devices attached
to the bus.
Only one device at a time can successfully transmit a signal.

A bus contains several separate lines, each is assigned a


particular meaning or function.
The data lines provide a path for moving data between system
modules. Collectively, these lines are called the data bus.
When people refer to the bus of a computer, they usually mean
the data bus.
A data bus typically consists 8, 16, 32 or 64 separate lines. The
number of such lines is called the width of the data bus.
The width of the data bus determines the how many bits can be
transferred at a time, and it is a key factor in determining the
system performance.
The address lines are used to designate the source or destination
of the data on the data bus. Together, the address lines are
called the address bus.

The control lines are used to control use of the data and
address lines. The control lines together are called the control
bus. The control bus carries the signals to read or write the
data to a specified address location.
Thus in a memory access by the CPU, control bus carries
memory access command, address bus carries memory
address, and data bus carries the data.

Data Bus

CPU

Address Bus

Main
Memory

Control Bus

Buses between CPU and Memory

Instruction Decoder
IR

Internal Bus

MEMORY

PC
Address
Lines

MAR
MDR

Data
Lines

R0

R(n-1)

Y
ALU
Control
Lines

Add
Sub

B
ALU
Z

Single-bus organization of the Data paths inside the CPU

You might also like