Global Positioning System (GPS)

Joe Montana
IT 488 - Fall 2003

Source Material:
http://www.trimble.com/gps
Leila Z. Ribeiro Class Handouts

GPS Creation
The U.S. Department of Defense
decided that the military had to
have a very precise form of
worldwide positioning.
And fortunately they had the kind
of money ($12 Billion!) it took to
build it.
3

What is GPS
Worldwide radio-navigation system formed
from a constellation of 24 satellites and their
ground stations.
Uses satellites as reference points to
calculate positions accurate to a matter of
meters (advanced forms of GPS can achieve
centimeter accuracy).
GPS receivers miniaturized and becoming
very economical and accessible to the end
users.
Applications in cars, boats, planes,
construction equipment, movie making gear,
farm machinery, etc.
4

GPS Satellites
Name: NAVSTAR Manufacturer: Rockwell
International
Altitude: 10,900 nautical miles
Weight:1900 lbs (in orbit)
Size:17 ft with solar panels extended
Orbital Period: 12 hours
Orbital Plane: 55 degrees to equitorial plane
Planned Lifespan: 7.5 years
Current constellation: 24 Block II
production satellites
Future satellites: 21 Block IIrs developed by
Martin Marietta.
5

Ground Control Stations

Also known as the "Control Segment.
Monitor the GPS satellites, checking both their
operational health and their exact position in
space.
The master ground station transmits corrections
for the satellite's ephemeris constants and clock
offsets back to the satellites themselves.
The satellites can then incorporate these updates
in the signals they send to GPS receivers.
There are five monitor stations: Hawaii, Ascension
Island, Diego Garcia, Kwajalein, and Colorado
Springs.
6

How GPS works

1.
2.
3.
4.

5.

The basis of GPS is "triangulation" from

satellites (formally speaking, trilateration).
To "triangulate," a GPS receiver measures
distance using the travel time of radio signals.
To measure travel time, GPS needs very
accurate timing which it achieves with some
specific techniques.
Along with distance, the receiver needs to know
exactly where the satellites are in space.
High orbits and careful monitoring contribute to
this accuracy.
Finally the receiver must correct for any
delays the signal experiences as it travels
through the atmosphere.
7

1 - Triangulation from Satellites

Use satellites in space as reference

points for location on earth.
How does the knowledge of distance
from three (or more) satellites allow
the position determination?
8

Triangulation - Basics
1. Position is calculated from distance
measurements (ranges) to satellites.
2. Mathematically we need four satellite
ranges to determine exact position.
3. Three ranges are enough if we reject
ridiculous answers or use other auxiliary.
4. Another range is required for technical
reasons to be discussed later.
9

Distance to one satellite

Suppose we measure our distance from a satellite and find
it to be 11,000 miles. (How we measure that distance is
the subject of further discussion)
Knowing that we're 11,000 miles from a particular satellite
narrows down all the possible locations we could be in the
whole universe to the surface of a sphere that is centered
on this satellite and has a radius of 11,000 miles.

10

Distance to two satellites

Next, suppose we measure our distance to a second
satellite and find out that it's 12,000 miles away.
That tells us that we're not only on the first sphere but
we're also on a sphere that's 12,000 miles from the
second satellite. Or in other words, we're somewhere on
the circle where these two spheres intersect.

11,000
miles sphere

12,000
miles sphere

11

Distance to three satellites

If we then make a measurement from a third satellite
and find that we're 13,000 miles from that one, that
narrows our position down even farther, to the two
points where the 13,000 mile sphere cuts through the
circle that's the intersection of the
two spheres.
Threefirst
measurements
put us at
one of these two points

11,000
miles sphere

13,000
miles sphere
12,000
miles sphere

12

Triangulation - Summary
By ranging from three satellites we can narrow
our position to just two points in space.
To decide which one is our true location we could
make a fourth measurement. But usually one of
the two points is a ridiculous answer (either too
far from Earth or an impossible velocity) and can
be rejected without a measurement.
A fourth measurement does come in very handy
for another reason however, but we will see that
later.
Next we'll see how the system measures
distances to satellites.
13

2 - Measuring distance from a satellite

From last section: position is calculated from
distance measurements to at least three satellites.
But how to measure the distance?
Solution: By timing how long it takes for a
signal sent from the satellite to arrive at the
receiver.

Speed of light: c = 300,000 km/sec

Distance to satellite is d = c x Td
The problem is measuring the
travel time.
14

Measuring Travel Time

A Pseudo Random Code (PRC) is transmitted from each satellite.
Physically it's a pseudo-random sequence of "on" and "off"
pulses.
Receiver knows the time of transmission of the satellite sequence.
By synchronizing the received sequence with a locally generated
sequence, the receiver can identify the relative delay between the
satellite and its location.

Transmission
from satellite
Reception at
GPS receiver
Td = Time elapsed between
satellite and receiver

15

Reasons for using pseudo random sequences

Avoid accidental synchronism with other interfering signal.
The patterns are so complex that it's highly unlikely that a
stray signal will have exactly the same shape.
Since each satellite has its own unique Pseudo-Random
Code they allow satellite identification. So all the satellites
can use the same frequency.
Pseudo-random sequences also make it more difficult for a
hostile force to jam the system. In fact the Pseudo
Random Code gives the DoD a way to control access to
the system.
Most importantly, the spread-spectrum effect gives
spreading gain, which allows the receiver to amplify the
signal at de-spreading. This enhances the link budget and
allows economical GPS receiver (portable units with low
gain antennas).

16

GPS Signals
The GPS satellites transmit signals on two
carrier frequencies.
The L1 carrier is 1575.42 MHz and carries both
the status message and a pseudo-random code
for timing.
The L2 carrier is 1227.60 MHz and is used for
the more precise military pseudo-random code.

Navigation Message: low frequency signal

added to the L1 codes that gives
information about the satellite's orbits, their
clock corrections and other system status.
17

Pseudo-Random Codes
There are two types of pseudo-random code.
The first pseudo-random code is called the C/A (Coarse
Acquisition) code. It modulates the L1 carrier. It repeats
every 1023 bits and modulates at a 1MHz rate. Each
satellite has a unique pseudo-random code. The C/A code
is the basis for civilian GPS use. CA code is at 1.024 Mbps.
The second pseudo-random code is called the P (Precise)
code. It repeats on a seven day cycle and modulates both
the L1 and L2 carriers at a 10MHz rate. This code is
intended for military users and can be encrypted. When
it's encrypted it's called "Y" code. Since P code is more
complicated than C/A it's more difficult for receivers to
acquire. That's why many military receivers start by
acquiring the C/A code first and then move on to P code. P
code is at 10.24 Mbps.

18

Summary Measuring Distances

1.
2.

3.

4.

Distance to a satellite is determined by

measuring how long a radio signal takes to
reach the user from that satellite.
To make the measurement we assume that
both the satellite and the users receiver are
generating the same pseudo-random codes at
exactly the same time.
By comparing how late the satellite's pseudorandom code appears compared to the
receiver's code, the receiver determines how
long the signal took to reach it.
Multiply that travel time by the speed of light
and you've got distance.
19

Summary Measuring Distances

1.
2.

3.

4.

Distance to a satellite is determined by measuring

how long a radio signal takes to reach the user
from that satellite.
To make the measurement we assume that both
the satellite and the users receiver are
generating the same pseudo-random codes at
exactly the same time.
By comparing how late the satellite's pseudorandom code appears compared to the receiver's
code, the receiver determines how long the signal
took to reach it.
Multiply that travel time by the speed of light and
you've got distance.

But to measure the time a perfect synchronism would be required!!

20

3 - Timing
Timing is critical: 1ms means a 200 mile error!
Remember that both the satellite and the receiver
need to be able to precisely synchronize their
pseudo-random codes to make the system work.
On the satellite side, timing is almost perfect
because they have incredibly precise atomic
clocks on board.
But what about receivers on the ground?

21

Position error due to wrong timing

22

Timing at receivers
If our receivers needed atomic clocks (which cost
upwards of $50K to $100K) GPS would be noneconomical.
Solution to this problem is to make an extra
satellite measurement.
This is one of the key elements of GPS and as an
added side benefit it means that every GPS
receiver is essentially an atomic-accuracy clock.
In other words: if three perfect measurements
can locate a point in 3-dimensional space, then
four imperfect measurements can do the same
thing.

23

How timing works at receivers

If timing was perfect (i.e. if receiver's clocks were
perfect) then all satellite ranges would intersect at a single
point (which is the receivers position). But with imperfect
clocks, a fourth measurement, done as a cross-check, will
NOT intersect with the first three.
So the receiver's computer can detect the discrepancy in
time measurements and recognize that it is out of
synchronism with universal time.
Since any offset from universal time will affect all of
receiver measurements, the receiver looks for a single
correction factor that it can subtract from all its timing
measurements that would cause them all to intersect at a
single point.
That correction brings the receiver's clock back into sync
with universal time, providing atomic accuracy time to it.

24

How timing works at receivers (cont.)

Once receiver has the timing correction it applies to all
the rest of its measurements and allows precise
positioning.
One consequence of this principle is that any GPS
receiver will need to have at least four channels so that
it can make the four measurements simultaneously .

But for the triangulation to work we not only

need to know distance, we also need to know
exactly where the satellites are.
In the next section we'll see how we
accomplish that.

25

Summary - Timing
1.
2.
3.

Accurate timing is the key to measuring

distance to satellites.
Satellites are accurate because they have
atomic clocks on board.
Receiver clocks don't have to be too accurate
because an extra satellite range measurement
can remove errors.
But for the triangulation to work we need
not only to know distance, we also need to
know exactly where the satellites are.
NEXT SECTION
26

4 - Satellite Position in Space

On the ground all GPS receivers have an
almanac programmed into their
computers that tells them where in the
sky each satellite is, moment by moment.

27

Monitoring Satellite Position

Orbits constantly monitored by the
Department of Defense.
They use very precise radar to check each
satellite's exact altitude, position and
speed.
Errors in position caused by gravitational
pulls from the moon and sun and by the
pressure of solar radiation on the satellites.
The errors are usually very slight because
of high orbit (MEO), but for accuracy they
must be taken into account.
28

Monitoring Satellite Position (cont.)

Once the DoD has measured a satellite's
exact position, they relay that information
back up to the satellite itself. The satellite
then includes this new corrected position
information in the timing signals it's
broadcasting.
That is why a GPS signal is more than just
pseudo-random code for timing purposes.
It also contains a navigation message
with ephemeris information as well.
29

Summary Satellite Position

To use the satellites as references for range
measurements we need to know exactly
where they are.
2. GPS satellites are being at high orbits (MEO),
are very predictable.
3. Minor variations in their orbits are measured
by the Department of Defense.
4. The error information is sent to the satellites,
to be transmitted along with the timing
signals.
1.

30

5 Additional Errors
Assumption distance to a satellite can be
calculated by multiplying a signal's travel time by
the speed of light was simplified so far: speed of
light is only constant in a vacuum.
As a GPS signal passes through the charged
particles of the ionosphere and then through the
water vapor in the troposphere it gets slowed
down, and this creates the same kind of error as
bad clocks.

31

Correcting delay errors

To minimize the errors described, one can predict what a
typical delay might be on a typical day. This is called
modeling and provides considerable improvement but with
limitations because atmospheric conditions are rarely typical.
Another technique to minimize on these atmosphere-induced
errors is to compare the relative speeds of two different
signals. This "dual frequency" measurement is very
sophisticated and is only possible with advanced receivers:
Physics says that as light moves through a given medium,
low-frequency signals get "refracted" or slowed more than
high-frequency signals. By comparing the delays of the
two different carrier frequencies of the GPS signal, L1 and
L2, we can deduce what the medium (i.e. atmosphere) is,
and we can correct for it.
Unfortunately this requires a very sophisticated receiver
since only the military has access to the signals on the L2
carrier.

32

Other sources of error

Multipath error: The signal may bounce off
various local obstructions before it gets to our
receiver.
Atomic clocks imperfections (small not null).
Position detection errors.
Geometric Dilution of Precision.
Intentional errors (removed in 2000) by the
DoD. The policy was called "Selective
Availability" or "SA" and the idea behind it was
to introduce inaccuracies to make sure that no
hostile force or terrorist group could use GPS to
make accurate weapons.

33

Geometric Dilution of Precision

Basic geometry itself can magnify these other errors
with a principle called "Geometric Dilution of
Precision" or GDOP.
It sounds complicated but the principle is quite simple.
There are usually more satellites available than a
receiver needs to fix a position, so the receiver picks a
few and ignores the rest.
If it picks satellites that are close together in the sky
the intersecting circles that define a position will cross
at very shallow angles. That increases the gray area or
error margin around a position.
If it picks satellites that are widely separated the
circles intersect at almost right angles and that
minimizes the error region.
Good receivers determine which satellites will give the
lowest GDOP.

34

Geometric Dilution of Precision (cont.)

35

Summary - Correcting Errors

1. The earth's ionosphere and atmosphere
cause delays in the GPS signal that
translate into position errors.
2. Some errors can be factored out using
mathematics and modeling.
3. The configuration of the satellites in the sky
can magnify other errors.
4. Differential GPS can eliminate almost all
error.

36

GPS Flavors
"Differential GPS," involves the use of two receivers.
One monitors variations in the GPS signal and
communicates those variations to the other receiver.
The second receiver can then correct its calculations for
better accuracy.
"Carrier-phase GPS" takes advantage of the GPS
signal's carrier signal to improve accuracy. The carrier
frequency is much higher than the GPS signal which
means it can be used for more precise timing
measurements.
"Augmented GPS" (aviation industry) involves the use
of a geostationary satellite as a relay station for the
transmission of differential corrections and GPS satellite
status information. These corrections are necessary if
GPS is to be used for instrument landings. The
geostationary satellite would provide corrections across
an entire continent.

37

Differential GPS
Error in position location is bias plus random
error.
Bias is same over a wide area caused by
delay in atmosphere, ephemeris error, etc.
Fixed receiver at a known location can measure
bias error.
Radio communication link to user allows
removal of bias error.
Extra receiver and data links increases cost
considerably.
Used to be more essential for civil applications
before removal of Selective Availability (2000).
38

GPS Accuracy
C/A (civil): About 10 meters

P (military): Can get down to

centimeter with the use of differential
GPS techniques.

39

GPS Applications
Civil Location - determining a basic position
Tracking - monitoring the movement of people
and things. Timing - providing atomic clock
precision.
Military: primary targeting and navigation
system for US armed forces.
Surveying: Mapping and locating land areas.
Vehicular Navigation: on-car navigation systems.
Ship navigation: Especially in coastal and inland
waters.
Aircraft navigations and landing: with
development of Augmented GPS by FAA.
40

GPS Limitations
Receiver must have line of sight to
four or more satellites.
Cannot work indoors of if sky is
blocked (by buildings or other solid
obstructions).
Accuracy in vertical dimension is
lower than in horizontal.
CA code may be vulnerable to
interference and jamming.
41

Other options of navigation systems

Landmarks: Only work in local area. Subject to
movement or destruction by environmental factors.
Dead Reckoning:Very complicated. Accuracy depends
on measurement tools which are usually relatively crude.
Errors accumulate quickly.
Celestial:Complicated. Only works at night in good
weather. Limited precision.
OMEGA:Based on relatively few radio direction beacons.
Accuracy limited and subject to radio interference.
LORAN:Limited coverage (mostly coastal). Accuracy
variable, affected by geographic situation. Easy to jam or
disturb.
SatNav:Based on low-frequency doppler measurements
so it's sensitive to small movements at receiver. Few
satellites so updates are infrequent.

42