Scribd
Upload
644 views

RSO Testing

RSO TEST

Uploaded by

Antonio Dsfvsdc
Copyright
© © All Rights Reserved
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
644 views

RSO Testing

RSO TEST

Uploaded by

Antonio Dsfvsdc
Copyright
© © All Rights Reserved
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
You are on page 1/ 19

TESTING GENERATOR ROTOR WINDINGS

USING THE RSO TEST METHOD

ROWTEST LTD.

Large high-speed electrical generators use a rotating magnetic field


produced by a cylindrical rotor in the form of a electromagnet having either
2 or 4 magnetic poles. The rotor body is a solid steel forging containing
radial slots for the coils which make up the electromagnets (rotor windings).
The turns of the coils are rectangular copper bars, insulated with an epoxy
material and in a 2-pole rotor, there are typically 8 pairs of slots for each
pole of the electromagnet.

Each winding slot contains up to 20


conductor turns. The figure shows a
cross-section of a typical radial slot (in
this case, containing 15 turns of
insulated copper bar).
At the ends of the rotor body, the turns
pass from the end of one slot to its
equivalent slot on the other side of the
magnetic pole and are held in place in
the end regions by steel end rings. A
direct current of around 3000 amps
flows through the rotor winding to
produce the magnetic field, which is at
right-angles to the axis of rotation, with
clearly-defined north and south poles.

A 2-pole rotor rotates at 3000/3600 rpm to


produce a 50Hz or 60Hz alternating
voltage in the (3-phase) stator windings.
The rotor windings experience large
centrifugal forces, which can damage the
insulation, leading to either shorts
between the rotor winding and ground or
between adjacent turns as shown in the
figure.
As the DC current is large and the short
circuits will have finite resistance, large
quantities of heat can be generated at the
fault location and this can cause damage
to the remaining insulation, resulting in
severe damage to the rotor windings.
Short circuits can also cause magnetic
imbalance, giving rise to increased
vibration levels.

Generator rotors are routinely tested to detect these types of fault, usually
during construction and also before routine generator maintenance.
One standard test method used is based on the use of time-domain
reflectometry (TDR), and is based on the methods used by
telecommunications engineers to locate faults on telephone and data
network transmission lines.
However, unlike the technique used for testing transmission lines, the rotor
winding is a very imperfect transmission line and produces a large number
of reflections at each change in impedance between the sections of
conductors inside the radial slots and the sections in the cross-over end
regions. This makes it virtually impossible to identify rotor winding faults by
simply observing the TDR waveforms.
Consequently, a modified version of the TDR method must be used with
rotor windings. A custom test instrument (Rotor Reflectometer) is used to
carry out this test, which is known as the Recurrent Surge Oscilloscope
(RSO) method by Power Engineers.

The RSO test method overcomes the problem of multiple reflections within
the rotor winding. It can detect and locate earth faults or shorted turns in
rotor windings and relies on the fact that the rotor winding is symmetrical.
For example, a 2-pole rotor contains two nominally-identical half-windings,
one for the North pole and the other for the South pole, both of which are
connected in series as shown above. A four pole rotor is similarly
symmetrical.

This symmetry property is used to compare the response of the 2 halves of


the rotor winding to a voltage pulse applied between each slip-ring and the
rotor body. The pulses and any reflected signals are monitored at each end of
the rotor winding using an oscilloscope. If the rotor winding is fault-free, two
identical waveforms will be observed at each slip ring. However, if one halfwinding contains a fault, the two waveforms will differ.

A (typically) square wave pulse (12V) is applied between one of the rotor slip
rings and ground and the transmitted pulse received at the remote end of the
rotor and the reflected pulse at the sending end are monitored.
The pulse takes a finite time (the transit time) to travel from one end of the
winding to the other and emerges at the far end as a slowly rising ramp
because of distortion effects in the winding.
Simplified (and idealised) versions of these waveforms are shown above.

Input ends

Output ends

The RSO test is carried out by applying pulses from each end of the rotor
winding in turn and the oscilloscope traces at each end of the winding are
recorded and compared. If the rotor is fault-free, the oscilloscope traces will be
identical.
Examples of real waveforms for a fault-free rotor at the input and output ends of
the rotor winding are shown in the figures above

In practice, the TDR100 test instrument has a switching circuit which applies
pulses alternately from each end of the rotor winding so that the waveforms
are automatically superimposed when viewed on a single channel
oscilloscope.

Short circuit to rotor body at end of 5th coil slot


(16 coils in winding)

When an earth fault occurs part


way along the winding, the traces
that occur are as shown above,

If there is an interturn fault, the


waveform at the slip ring nearest the
fault is characterised by a slight
increase in voltage followed by a
decrease down to a minimum,
followed by a slow voltage rise, as
shown above

A typical measurement arrangement is shown above and in the next slide and
assumes the use of a basic two channel analogue oscilloscope, although a
single channel instrument will suffice if a 2-channel oscilloscope is not
available.

TDR100 RSO Measurement system

The photo shows the controls on the front panel of a Rowtest TDR100
Reflectometer. This is an analogue instrument which displays the rotor
waveforms on an oscilloscope screen.

The operation of the Reflectometer can be demonstrated and checked


using a delay line module, which simulates (approximately) the electrical
characteristics of the rotor winding.

The delay line contains 10 sections of series inductance and parallel


capacitance and is designed to produce a characteristic impedance of 100
and a propagation delay of 11S.
The junctions between each section of the delay line are connected to a
series of 2mm sockets, enabling external connection to these points. The
input and output ends of the unit are connected to 4mm sockets.

The effect of a simulated earth fault can be demonstrated by shorting one


of the delay line junctions to earth using the 2mm plug leads. Fig. (a)
shows the result of shorting junction 4 to earth.
Similarly the effect of a shorted turn can be demonstrated by shorting out
one or more delay line sections as shown in Fig. (b).

When the test method was first introduced, waveforms were often recorded
using Polaroid photography. Currently, digital cameras are used with either
analogue or digital oscilloscopes, as shown above.
When a digital oscilloscope is used, the waveform can also be captured to the
oscilloscopes internal memory and then transferred to a PC.

CONCLUSIONS

The RSO test is a safe (low voltage), sensitive and reliable method for detecting
and locating faults in the windings of large generator rotors. It is in regular use
for checking the integrity of rotor windings at Power Utilities, Manufacturers and
Repair Companies throughout the world.

For further information, please contact us at [email protected]

Copyright PTL. 2013.

You might also like