Scribd
Upload
2K views

Unit 1 Solid Mechanics

This document covers key points about solid mechanics including: - Torsion occurs when a torque is applied about the axis of a shaft, causing shear stresses that vary linearly from zero at the center to a maximum at the outer surface. The shear stress is proportional to the applied torque and polar second moment of area. - Beams can be loaded by point loads, uniform loads, or point moments which produce characteristic shear force and bending moment diagrams. Bending stresses are calculated using the beam bending equation. - Mohr's circle is used to analyze stresses at a point, determining principal stresses and maximum shear stresses. It graphically represents the transformation of stresses between planes. - Generalized Hooke's law relates direct stresses to strains

Uploaded by

Edison Chandraseelan
Copyright
© © All Rights Reserved
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
2K views

Unit 1 Solid Mechanics

This document covers key points about solid mechanics including: - Torsion occurs when a torque is applied about the axis of a shaft, causing shear stresses that vary linearly from zero at the center to a maximum at the outer surface. The shear stress is proportional to the applied torque and polar second moment of area. - Beams can be loaded by point loads, uniform loads, or point moments which produce characteristic shear force and bending moment diagrams. Bending stresses are calculated using the beam bending equation. - Mohr's circle is used to analyze stresses at a point, determining principal stresses and maximum shear stresses. It graphically represents the transformation of stresses between planes. - Generalized Hooke's law relates direct stresses to strains

Uploaded by

Edison Chandraseelan
Copyright
© © All Rights Reserved
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
You are on page 1/ 21

Solid mechanics 1.

1 key points

A force arises from the action (or reaction) of one


body on another.
Newtons third law tells us that the action and
reaction forces in this situation (and generally) are
equal and opposite.
The SI unit of force is the newton (N).
The moment of a force about a point is equal to
the product of the magnitude of the force and the
perpendicular distance from the point to the line of
action of the force.

Solid mechanics 1.1 key points

The three conditions of equilibrium are:

(i)
the sum of all the acting forces in the xdirection must be zero, i.e. Fx=0.

(ii)
The sum of all the acting forces in the ydirection must be zero, i.e. Fy=0.

(iii)
The sum of all the moments about any point
must be zero.

Solid mechanics 1.1 key points

Key points about freebody diagrams:

(i) A freebody diagram, as the name implies, is a


diagram of a freebody which shows all the external
forces acting on the body.

(ii)Where several bodies (or subcomponents) interact as


part of a more complex system, each body should be
drawn separately and interacting bodies should be
replaced at their contact points with suitable reaction
forces and/or moments.

Solid mechanics 1.1 key points

The two-force principle states that for a twoforce body (i.e. a body with forces applied at two
points only) to be in equilibrium, both forces must
act along the same line of action.

The three-force principle states that for a threeforce body (i.e. a body with forces applied at three
points only) to be in equilibrium, the lines of action
of these forces must pass through a common
point.

Solid mechanics 1.1


Learning summary
By the end of section 1.1 you will have learnt:

the basic definitions of forces, moments and couples;


how to use freebody diagrams and the basic conditions of
equilibrium to solve for unknown forces acting on or within a
structure;
how to analyse frictional forces at the contact between bodies or
structures;
general design principles including the two-force and three-force
principles which can be used to simplify the solution of specific
problems;
analytical and geometrical methods for solving for forces acting on
or within pin-jointed structures.

Solid mechanics 1.2 key points

The units of direct stress are the units of force


divided by area, i.e. N/m2, also known as pascal
(Pa).
Because strain is a ratio of lengths, it has no units
Elastic materials are fully recoverable upon
unloading.
The ratio of /, i.e. the gradient of this line, is
constant and called Youngs modulus (after the
scientist Thomas Young (17731829)).

Solid mechanics 1.2 key points

The equation = E is known as Hookes law


and, because it describes a straight line, materials
obeying it are termed linear elastic (NB: there are
some exceptions to this linear behaviour but most
engineering solids, at least at small deformations,
do obey the law).
The ratio of lateral strain to longitudinal strain
depends on the material and, like Youngs
modulus, is an important material property. It is
called Poissons ratio, denoted by the symbol
(nu), and named after the French mathematician
Simeon Denis Poisson (17811840).

Solid mechanics 1.2 key points

The yield point is the point beyond which


permanent deformations occur.
Shear stress results when a force is applied
parallel to an area.
Shear strain, denoted by the symbol (gamma),
is a measure of the angle of distortion resulting
from the applied shear stress.
Thus, shear stress is proportional to shear strain
and the constant of proportionality, G, is termed
the shear modulus.

Solid mechanics 1.2


Learning summary
By the end of this section you will have learnt:
the definitions of direct stress and strain and shear stress and
strain;

the principles of linear elasticity and Hookes law which relates


stress and strain through the material property Youngs modulus in
direct stress conditions, and Shear modulus in shear conditions,
both a measure of the stiffness of a material;

how lateral deformations are quantified by the material property,


Poissons ratio;

that there are generally two types of stressstrain problem, namely


statically determinate and statically indeterminate problems.
Statically determinate problems can be solved using the equations
of statics alone (i.e. equilibrium and the stress-strain relationship),
while statically indeterminate problems require further information
such as the compatibility of strains or deformations;
(continued...)

Solid mechanics 1.2


Learning summary
By the end of this section you will have learnt:

how temperature changes can give rise to stresses and strains in


bodies or structures even in the absence of any applied loading. In
such cases, an important material property, determining the
magnitude of these thermal stresses and strains, is the coefficient
of thermal expansion of the material;
how to use the principle of superposition to solve problems
involving both mechanical and thermal loading.

Solid mechanics 1.3 key points

The knife edge simple support, Figure 1.41(a),


is modelled with a vertical reaction force which
constrains vertical movement but allows free
rotation of the beam at the support.
The built-in support, Figure 1.41(b), is modelled
with a vertical reaction force and a reaction
moment which constrain vertical movement and
rotation respectively at the support. This type of
support is also referred to as encastre.

Solid mechanics 1.3 key points

A point load has units of newtons (N) and acts


vertically at a point along the beam span. A
uniformly distributed load, shortened to UDL,
has units of Newtons per metre length of beam
(Nm-1), and acts over the full span or part of the
span. Finally, a point moment has units of Nm
and again acts at a point along the beam span.
A positive shear force results in anticlockwise
rotation of the face on which it acts.
A negative shear force results in clockwise
rotation of the face on which it acts.

Solid mechanics 1.3 key points

A positive bending moment results in sagging of


the beam.
A negative bending moment results in hogging of
the beam.
The second moment of area about the NA is a
measure of the distribution of the area within the
beam cross-section and is an important structural
term in bending.

Solid mechanics 1.3


Learning summary
By the end of this section you will have learnt:

various types of beam, their supports and loading conditions;


how to calculate and draw shear force and bending moment
distribution diagrams for beams under point loading, UDL and
concentrated moments;
beam bending theory and the derivation of the beam bending
equation relating the bending moment to bending stress and radius
of curvature;
how to calculate the second moments of area of simple and more
complex sections such as I-sections and T-sections;
the general procedure for calculating stresses within beams.

Solid mechanics 1.4 key points

An x-plane is defined as a plane whose normal


acts in the x-direction. Thus, the right hand edge
and the left hand edge of the element are both xplanes.
A y-plane is defined as a plane whose normal acts
in the y-direction. Thus, the top edge and the
bottom edge of the element are both y-planes.
A positive shear stress is trying to rotate the
element anticlockwise. xy is therefore positive on
both the right-hand and left-hand edges.

Solid mechanics 1.4 key points

A negative shear stress is trying to rotate the


element clockwise. yx is therefore negative on
both the top and bottom edges.
Mohrs circle is a graphical construction
representing the above transformation equations.

Solid mechanics 1.4


Learning summary
By the end of this section you will have learnt:

about stresses and strains acting in a single plane (twodimensional) and how we define the general state of plane stress;
the general equations for the angular transformation of stresses in
two-dimensional and how these equations may be represented by
a graphical construction called Mohrs circle for plane stress;
the use of Mohrs circle to analyse stresses at a point in a material
and determine the planes of maximum direct stress, i.e. the
Principal Planes, on which the Principal Stresses act, and the
planes of maximum shear stress;
The derivation of Generalised Hookes Law relating direct stresses
to direct strains in three dimensions and its application in solving
three-dimensional problems, including stresses in thin cylinders
and spheres and hydrostatic stress/volumetric strain problems.

Solid mechanics 1.5 key points

When a moment is applied about the axis of a


shaft or bar, as shown in Figure 1.79, it is termed
a torque and the shaft is said to be under a state
of torsion.
We now define a new geometric quantity, J, the
polar second moment of area given by

J r dA
2

Solid mechanics 1.5 key points

J is an important term in torsion and describes the


distribution of the elements of area about the axis
of the shaft. Its units are m 4.
Note that for a given T and J, the shear stress, ,
is proportional to r and is a maximum at r = outer
radius, i.e. on the surface of the shaft, and a
minimum, = 0, at the centre of the shaft. The
shear stress varies linearly with radial position.[

Solid mechanics 1.5 key points

J is an important term in torsion and describes the


distribution of the elements of area about the axis of
the shaft. Its units are m4.
Note that for a given T and J, the shear stress, , is
proportional to r and is a maximum at r = outer
radius, i.e. on the surface of the shaft, and a
minimum, = 0, at the centre of the shaft. The shear
stress varies linearly with radial position.[
When a moment is applied about the axis of a shaft
or bar, as shown in Figure 1.79, it is termed a
torque and the shaft is said to be under a state of
torsion.

Solid mechanics 1.5


Learning summary
By the end of this section you will have learnt:

the definition of torque and how it gives rise to twist and shear
stresses within a shaft;
the derivation of the torsion equation and how it is used to
calculate twist angle and shear stresses in a shaft subjected to a
known torque;
how to calculate the polar second moment of area for solid and
hollow circular cross-sections;
how to solve torsion problems including power transmission,
stepped and composite shafts.

You might also like