Scribd
Upload
31 views

Eng 313 Instructions

This document provides assembly instructions for a mini helicopter rescue set in 5 phases. It includes a parts list, images of parts used and not used, and step-by-step instructions for assembling the base, main body, rotor, tail, and putting all parts together. The full assembly requires 18 different LEGO elements and takes the builder through attaching and positioning the various components to create a miniature helicopter model.

Uploaded by

api-341481240
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
31 views

Eng 313 Instructions

This document provides assembly instructions for a mini helicopter rescue set in 5 phases. It includes a parts list, images of parts used and not used, and step-by-step instructions for assembling the base, main body, rotor, tail, and putting all parts together. The full assembly requires 18 different LEGO elements and takes the builder through attaching and positioning the various components to create a miniature helicopter model.

Uploaded by

api-341481240
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
You are on page 1/ 32

Mini Helicopter Rescue 6911

Instruction Manual
By:
Eleanor Chambers, Sharon Svetov, Chad Goss,
Tre Hawkins, Vincent Tong, and Matthew Gardner

Intended for ages 6-12


Not for children under 3
Small pieces are a choking hazard.

Table of Contents
Parts Lists:

Slides 4-7

Phase 1:

Slides 8-11

Phase 2:

Slides 12-17

Phase 3:

Slides 18-21

Phase 4:

Slides 22-26

Phase 5:

Slides 27-32

Parts Used
1. 1x6
Dark
Grey
(2)
2. 2x6
Red (1)
3. 2x4
Red (2)
4. 2x4
White
(1)
5. 1x2
Smooth
Yellow

13. 1x2 Grey


Vent (4)
14. 1x1 Clear
Yellow
Wedge (1)
15. 1x1 Clear
Red Wedge
(2)
16. 1x1 Grey
Wedge (2)
17. 1x1 Clear
Blue Wege
(2)
18. 2x3 Red

Image of Parts Used

Parts Not Used


1. 2x2 Red
2. 1x1
Brick (2)
3. 1x2
Clear
Brick (3)
4. 2x1
grey
handle
(2)
5. 1x2
black
claw (2)
6. 2x2

13. Red
Flat Corner
14. White
two sided L
15. Red
two sided
16. Grey
Hammer
17. 1x1
Black Circle
(1)

Image of Parts Not Used

Phase 1: Base
3 steps total

Parts Needed For Phase 1:


1. (2) 1x4 Red
2. (1) 2x4 White
3. (1) 2x4 Red
4. (1) 1x2 Dark Grey Brick
5. (1) White Two-Sided L
6. (1) 1x2 Red

Phase 1: Step 1
Attach 1 2x4 White to the top of two 1x4 Red pieces as seen below.

Phase 1: Step 2
Attach 1 1x2 Dark Grey Brick to the top of a 2x4 Red piece. This is then
attached to the top of what was made in step 1 as seen below.

Phase 1: Step 3
Attach 2 1x1 Clear Red Wedge to the bottom of the 1 White Two-Sided L.
Above the wedges attach 1 1x2 Red and on top of the 1x2 Red attach a 1x2
Grey Vent.
This part is then attached to the 1x2 Dark Grey Brick as seen below.

Phase 2: Main Body


5 Step Tutorial

Parts Needed for Phase 2


1. (1) 2x4 Red
2. (1) 2x3 Red
3. (2) 1x1 Grey Wedge
4. (2) 1x1 Clear Blue Wedge
5. (1) 1x2 Clear Brick

Phase 2: Step 1
Attach 2 1x1 Grey Wedge to the front of the top of the 1 2x4 Red.

Phase 2: Step 2
Behind the 1x1 Grey Wedges attach 1 2x3 Red to the top of the 2x4 Red.

Phase 2: Step 3
Attach 1 1x2 Red to the front of the 2x3 Red.
On top of the 1 1x2 attach 2 1x1 Clear Blue Wedge.

Phase 2: Step 4
Behind the 2 1x1 Clear Blue Wedges attach 1 1x2 Clear Brick to the 2x3 Red.
Behind the 1x2 Clear Brick, attach 1 1x2 Red to the 2x3 Red.

Phase 2: Step 5
Attach 1 1x2 Red to the top of the 1x2 Red placed in previous step.
Attach 2 1x1 Grey with Cylinder to the top of the 1x2 Red.
Attach 2 1x1 Black Circle to the Cylinder portion of the 1x1 Grey with Cylinder.

Phase 3: The Rotor


3 Steps Total
Parts Needed for Phase 3
1. (1)2x2 White & Grey Spinner
2. (2) 1x2 Smooth Yellow
3. (2) 1x6 Dark Grey
4. (2) 1x2 Grey Vents

Phase 3: Step 1
Attach 1x2 Smooth Yellow to the end of 1x6 Dark Grey
Attach other 1x2 Smooth Yellow to the end of 1x6 Dark Grey

Phase 3: Step 2
Attach one 1x6 Grey Piece to 2x2 White Grey Spinner with yellow piece farthest
from the Spinner
Attach the other 1x6 Grey Piece to 2x2 White Grey Spinner with end facing in
opposite direction

Phase 3: Step 3
Attach both 1x2 Grey Vents perpendicular to both 1x6 pieces, parallel to one
another

Phase 4: The Tail


4 Steps Total

Parts Needed for Phase 4


1. (1) 1x1 Clear Yellow Wedge
2. (1) Red Flat Corner
3. (1) 1x2 Grey Claws
4. (2) 1x2 Grey Hinge
5. (1) 1x2 Grey Vent
6. (1) 2x2 Grey Axel

Phase 4: Step 1
Attach 2 of the 1x1 black circles to the second row of the 2x3 Red next to one
another
Attach the 2x2 Grey Axel to one end of the 2x3 Red piece (one side of the 2x2
Grey Axel will hang off the red piece)

Phase 4: Step 2
Attach the 2x3 Red underneath the 2x6 Red at the end with one row of
connectors unused
On the fourth row from the side attached to the 2x3 Red, attach the 1x2 Grey
Vent to the 2x6 Red
Attach two 1x2 Grey hinges to the opposite end of the underneath 2x3 Red
piece

Phase 4: Step 3
Attach the grey claws to the end of the 1x2 Grey hinges
Attach the Red Flat corner to the Grey claws with one circle hanging off on the
side farther away from the 2x3 Red
Attach the 1x1 Clear Yellow Wedge to the top left corner of the farthest 1x2
Hinge so that the wedge points towards the vent

Phase 4: Step 4
Take what you produced in Phase 4 Step 1 and what you produced in Phase 4
Step 3
Attach Step 1s result to Step 3s result by connecting the 2x2 Grey Axel to the
2x6 Red Piece, overlapping the 2x3 Red Piece

Phase 5: Putting it all Together


4 Steps Total

Parts Needed for Phase 4


1. Phase 1 Final Product
2. Phase 2 Final Product
3. Phase 3 Final Product
4. Phase 4 Final Product

Phase 5: Putting everything together


Phase 1

Phase 3

Phase 4
Phase 2

Phase 5: Step 1
Attach Phase 2 on top of Phase 1 so the flat surfaces are against one another

Phase 5: Step 2
Attach Phase 4 directly on top of the result of Step 1 so that the 1x2 Clear Brick
and the front of Phase 4 are aligned

Phase 5: Step 3
Attach Phase 5 directly on top of the result of Step 2 so that the 2x2 White and
Grey Spinner is on top of the two 1x1 Black Circle and the front of the 2x2
Grey Axel

Final Product

You might also like