Scribd
Upload
163 views

SHO Overhead Optimization - v2

1) The document provides guidelines for optimizing 3G cell sites with high SHO overhead through parameter modification. 2) It identifies candidate cells based on SHO overhead, neighbor overshooting, antenna tilting and azimuth differences. 3) The guidelines aim to optimize SHO parameters to still meet OSS KPI targets for CCSR PS and CS while reducing SHO overhead.

Uploaded by

ahdanizar
Copyright
© © All Rights Reserved
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
163 views

SHO Overhead Optimization - v2

1) The document provides guidelines for optimizing 3G cell sites with high SHO overhead through parameter modification. 2) It identifies candidate cells based on SHO overhead, neighbor overshooting, antenna tilting and azimuth differences. 3) The guidelines aim to optimize SHO parameters to still meet OSS KPI targets for CCSR PS and CS while reducing SHO overhead.

Uploaded by

ahdanizar
Copyright
© © All Rights Reserved
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
You are on page 1/ 2

3G Roll-out Optimization

SHO Overhead Optimization


1. Cells with SHO OH Guideline
>50%
2. Cells with TP >
START ISD > 20%
3. Check cells DT RET tilt <
Y Perform RET until
optimum not
(1) Maximum mechanical tilt based on height and
ISD
coverage max exceeding ISD vs.
Tilting table
Check Y
Overshooti N
ng cells MOD
Candidate Cells for (3) 1BPS Y INTRARELTHDFOR1BP
parameter modification >8 OR S =8 (2) Rule 1,2 and 3 can have exemption for case
N 1APS >4 INTRARELTHDFOR1AP where target coverage is in conflict with the rules.
Rule1 1.Source cell with high SHOOH S=4
Antenna Re-azimuth N (3) Modifying SHO parameters should make CCSR
face to Y >10 2. Top 3 target sectors
with highest SHO attempts PS and CCSR CS still pass the OSS KPI target.
face with difference (3) Y MOD
neighbor with based on cell to cell counter TRIGTIME1
neighbor VS.SHO.AttASU.Ncel B>D320
TRIGTIME1B=320 (4) This guideline applies for SHO overhead
optimization, bad spot coverage optimization
N N (specially due to pilot pollution) will have to be
Rule2 fixed first or in parallel.
Re-azimuth
Overlap Y >10 (1)M or E (5) 3G new sites with site level SHO OH pass
tilt < max Y Perform mechanical target, but with at least 1 sector having
opposite difference
neighbor with based or electrical down tilt
ISD/height
neighbor Target SHO OH < Actual SHO OH <60%
N 43% < 55% < 60%
N Neighbor
Rule3
overshooti Y Perform neighbor AND already applied SHO OH guideline above, will
Azimuth Y ng
between
Re-azimuth optimization be considered for acceptance.
~TP
> 90
antenna >20%
difference
<=90 N
Best Effort
N Optimization done * For non-RET(new site), E tilt and M tilt should go
together.
3G Multi-Sector
Re-Azimuth guideline

More than 10 Rule 1: Opposite Antenna can


not face to face, the minimum
angle of them should more than
10 degrees;

Overlap no opposite More than 10 Rule 2: The overlap can not


opposite, the minimum angle of
them should more than 10
degrees;

Angle between Antennas larger than 90 Rule 3: The angle between 65


antenna and split antenna should be
Less than 90
more than 90 more than 90 degrees between the
split antenna should be more than 100
degree

You might also like