Scribd
Upload
325 views

555 Timer As Multivibrator

The document discusses different types of multivibrators including bistable, monostable, and astable. It then describes how the 555 timer integrated circuit can be used to create monostable and astable multivibrator circuits. Circuit diagrams and explanations are provided for 555 timer circuits in astable and monostable configurations. Design considerations like component values and their effect on output waveform are also covered.

Uploaded by

ShrutJain
Copyright
© © All Rights Reserved
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
325 views

555 Timer As Multivibrator

The document discusses different types of multivibrators including bistable, monostable, and astable. It then describes how the 555 timer integrated circuit can be used to create monostable and astable multivibrator circuits. Circuit diagrams and explanations are provided for 555 timer circuits in astable and monostable configurations. Design considerations like component values and their effect on output waveform are also covered.

Uploaded by

ShrutJain
Copyright
© © All Rights Reserved
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
You are on page 1/ 25

555 TIMER

AS
MULTIVIBRATOR
INTRODUCTION
A multivibrator is a circuit whose
output changes between two digital
levels.
Three types:
Bistable Multivibrator: When placed in either
state, it will stay there indefinitely; wont
spontaneously switch to the other state.
Bistable Multivibrators
can produce a very short output pulse or a much longer
rectangular shaped output
leading edge of pulse rises in time with the externally
applied trigger pulse and
trailing edge is dependent upon a second trigger pulse.
Bistable Multivibrator Waveform

Monostable (One-shot): Will stay in its


stable state indefinitely, but if forced into the
other state it will spontaneously switch back after
a certain time.
Monostable Multivibrators
can produce a very short pulse or a much longer
rectangular shaped waveform
leading edge rises in time with the externally applied
trigger pulse
trailing edge is dependent upon thetime constant
(RC) of the feedback components used.
Monostable Multivibrator Waveforms
Astable (Oscillator): From either state
it will spontaneously switch to the other
state after a certain time.
Astable Multivibrators
Can produce TWO very short square wave
output waveforms from each transistor or
A much longer rectangular shaped output
either symmetrical or non-symmetrical
depending upon the time constant of theRC
network.
Astable Multivibrator Waveforms
555 Timer

The 555 is a popular, versatile chip used in many


timing applications.
Dedicated IC especially designed to accurately
produce the required output waveform with the
addition of just a few extra timing components
By itself, its neither a one-shot nor an astable
multivibrator, but it can be hooked up to perform
as either of these.
The 555 timer chip is extremely robust and stable 8-pin
device
Can be operated either as a very accurate
Monostable,BistableorAstableMultivibrator or to produce a
variety of applications such as
one-shot or delay timers,
pulse generation,
LED and lamp flashers,
alarms and tone generation,
logic clocks,
frequency division,
power supplies and converters etc,
in fact any circuit that requires some form of time control as the list is
endless.
555 Timer Block Diagram
555 Input and Output
Pins
Aside from its power and ground pins,
the 555 has five input pins and one
output pin.

Pin diagram
from datasheet Logic symbol
The 555 timer as a monostable multivibrator

The 555 timer can be configured in various ways, including as


a one-shot. A basic one shot is shown. The pulse width is
determined by RAC and is approximately tW = 1.1RAC.

The trigger is a
negative-going
pulse.
The 555 timer as an astable multivibrator

The 555 can be configured as a basic astable multivibrator


with the circuit shown. In this circuit C charges through RA
and RB. It discharges through only RB. The time high, time
low, and frequency are given by:


The 555 timer as a bistable multivibrator
Circuit with Internal Block
Diagram
Astable Multivibrator using
555 Circuit

Above figure shows the circuit diagram of a 555 Timer wired in Astable
Mode. 8th pin and 1st pin of the IC are used to give power, Vcc and GND
respectively.
The 4th pin is RESET pin which is active low and is connected to Vcc to
avoid accidental resets. 5th pin is the Control Voltage pin which is not
used.
So to avoid high frequency noises it is connected to a capacitor C
whose other end is connected to ground. Usually C = 0.01F.
The Trigger (pin 2) and Threshold (pin 6) inputs are connected to the
capacitor which determines the output of the timer. Discharge pin (pin
7) is connected to the resistor Rb such that the capacitor can discharge
through Rb.
Diode D connected in parallel to Rb is only used when an output of duty
cycle less than or equal to 50% is required.
For the sake of explaing the working Circuit Diagram with Internal Block
diagram is shown below.
Astable Multivibrator using 555 Timer Block Diagram
Since the Control Voltage (pin 5) is not
used the comparator reference voltages
will be 2/3 Vcc and 1/3 Vcc respectively.
So the output of the 555 will set (goes
high) when the capacitor voltage goes
below 1/3 Vcc and output will reset (goes
low) when the capacitor voltage goes
above 2/3 Vcc.
Working
When the circuit is switched ON, the capacitor (C) voltage
will be less than 1/3 Vcc.
So the output of the lower comparator will be HIGH and of
the higher comparator will be LOW. This SETs the output of
the SRFlip-flop.
Thus the discharging transistor will be OFF and the capacitor
C starts charging from Vcc through resistor Ra & Rb.
When the capacitor voltage will become greater than 1/3
Vcc ( less than 2/3 Vcc ), the output of both comparators will
be LOW and the output of SR Flip-flop will be same as the
previous condition. Thus the capacitor continuous to charge.
When the capacitor voltage will becomes slightly greater than 2/3
Vcc the output of the higher comparator will be HIGH and of lower
comparator will be LOW. This resets the SR Flip-flop.
Thus the discharging transistor turns ON and the capacitor starts
discharging through resistor Rb.
Soon the capacitor voltage will be less than 2/3 Vcc and output of
both comparators will be LOW. So the output of the SR Flip-flop will
be the previous state.
So the discharging of capacitor continuous.
When the capacitor voltage will become less than 1/3 Vcc, the
output SETs since the output of lower comparator is HIGH and of
higher comparator is LOW and the capacitor starts charging again.
This process continuous and a rectangular wave will be obtained at
the output.
Design
Capacitor Charges throughRaandRb.
Thigh = 0.693(Ra + Rb)C
Capacitor Discharges throughRb
Tlow = 0.693RbC
Duty Cycle = Thigh/(Thigh + Tlow)
Where Thigh and Tlow are the time period of HIGH and
LOW of the output of 555.
From this we can find that Duty Cycle less than or equal to
50% cannot be obtained. There are two ways to obtain this.
1.Inverting the output
2.Using a Diode Parallel to resistor Rb
1.Inverting the Output
In this method, just compliment the output. Thus theDuty
Cycle = Tlow/(Tlow + Thigh). Where Tlow and Thigh are the
time period of LOW and HIGH of output of 555. In this method
the duty cycle of the output of 555 will be greater than 50%
and that of inverter will be less than 50%.
Duty Cycle of 555 = 1 Duty Cycle of Inverter
2.Using a Diode Parallel to resistor Rb
In this method we will connect a diode parallel to resistor Rb as
shown dotted in the first circuit diagram above. Thus the
charging current of capacitor will bypass the resistor Rb.
ThusThigh = 0.693RaC
Thus a Duty Cycle less than or equal to 50% can easily
obtained.

You might also like