Ultrasonic Testing

Part 2

Copyright 2004 WI Ltd Name

 Ultrasonic Testing techniques
Pulse Echo
Through Transmission
Transmission with Reflection

Copyright 2004 WI Ltd Name

 Pulse Echo Technique
Single probe sends
and receives sound
Gives an indication of
defect depth and
dimensions
Not fail safe

Copyright 2004 WI Ltd Name

 Defect Position

B
A

No indication from defect A (wrong orientation)

Copyright 2004 WI Ltd Name
 Through Transmission Technique
Tx Rx
Transmitting and
receiving probes
on opposite sides
of the specimen

Presence of defect
indicated by
reduction in
transmission signal

No indication of
defect location

Fail safe method

Copyright 2004 WI Ltd Name

Copyright 2004 WI Ltd Name
 Through Transmission Technique

Advantages Disadvantages
Less attenuation Defect not located
No probe ringing Defect cant be
No dead zone identified
Orientation does not Vertical defects
matter dont show
Must be automated
Need access to both
surfaces
Copyright 2004 WI Ltd Name
 Transmission with Reflection
T R

Also known as:

Tandem Technique or
Pitch and Catch Technique
Copyright 2004 WI Ltd Name
 Ultrasonic Pulse
A short pulse of electricity is applied to a
piezo-electric crystal
The crystal begins to vibration increases
to maximum amplitude and then decays
Maximum

10% of
Maximum

Pulse length
Copyright 2004 WI Ltd Name
 Pulse Length
The longer the pulse, the more
penetrating the sound
The shorter the pulse the better the
sensitivity and resolution

Short pulse, 1 or 2 cycles Long pulse 12 cycles

Copyright 2004 WI Ltd Name
 Ideal Pulse Length

5 cycles for weld testing

Copyright 2004 WI Ltd Name

 The Sound Beam
Dead Zone
Near Zone or Fresnel Zone
Far Zone or Fraunhofer Zone

Copyright 2004 WI Ltd Name

 The Sound Beam

NZ FZ Main
Beam

Intensity
varies

Exponential Decay

Copyright 2004 WI Ltd Distance Name

 The side lobes has multi
minute main beams
Two identical defects may
give different amplitudes of
signals

Near
Side Lobes
Zone
The main beam or the centre
beam has the highest
intensity of sound energy

Main Lobe Any reflector hit by the main

beam will reflect the high
amount of energy
Main Beam

Copyright 2004 WI Ltd Name

 Sound Beam
Near Zone Far Zone
Thickness Thickness
measurement measurement
Detection of defects Defect detection
Sizing of large Sizing of all defects
defects only

Near zone length as small as possible

Copyright 2004 WI Ltd Name

 Near Zone

2
D
Near Zone
4
V

f
2
D f
Near Zone
4V
Copyright 2004 WI Ltd Name
 Near Zone
What is the near zone length of a 5MHz
compression probe with a crystal diameter
of 10mm in steel?
2
D f
Near Zone
4V
10 5,000,000
2

4 5,920,000
21.1mm
Copyright 2004 WI Ltd Name
 Near Zone
2 2
D D f
Near Zone
4 4V
The bigger the diameter the bigger the
near zone
The higher the frequency the bigger the
near zone
The lower the velocity the bigger the near
zone
Should large diameter crystal probes have a high
or low frequency?
Copyright 2004 WI Ltd Name
 Which of the above probes has the longest Near Zone ?

1 M Hz
5 M Hz
1 M Hz 5 M Hz

Copyright 2004 WI Ltd Name

 Near Zone
2 2
D D f
Near Zone
4 4V
The bigger the diameter the bigger the
near zone
The higher the frequency the bigger the
near zone
The lower the velocity the bigger the near
zone
Should large diameter crystal probes have a high
or low frequency?
Copyright 2004 WI Ltd Name
 Beam Spread
In the far zone sound pulses spread out
as they move away from the crystal

/2

K KV
Sine or
2 D Df
Copyright 2004 WI Ltd Name
 Beam Spread
K KV
Sine or
2 D Df
Edge,K=1.22
20dB,K=1.08
6dB,K=0.56
Beam axis
or Main Beam

Copyright 2004 WI Ltd Name

 Beam Spread
K KV
Sine or
2 D Df
The bigger the diameter the smaller the
beam spread
The higher the frequency the smaller
the beam spread

Which has the larger beam spread, a compression

or a shear wave probe?
Copyright 2004 WI Ltd Name
 Beam Spread
What is the beam spread of a 10mm,5MHz
compression wave probe in steel?

KV
Sine
2 Df
1.08 5920

5000 10
0.1278 7.35 o

Copyright 2004 WI Ltd Name

 Which of the above probes has the Largest Beam
Spread ?

1 M Hz
5 M Hz
1 M Hz 5 M Hz

Copyright 2004 WI Ltd Name

 Beam Spread
K KV
Sine or
2 D Df
The bigger the diameter the smaller the
beam spread
The higher the frequency the smaller
the beam spread

Which has the larger beam spread, a compression

or a shear wave probe?
Copyright 2004 WI Ltd Name
 Testing close to side walls

Copyright 2004 WI Ltd Name

 Sound at an Interface
Sound will be either transmitted across
or reflected back
Reflected

How much is reflected and

Interface transmitted depends upon the
relative acoustic impedance of
the 2 materials

Transmitted
Copyright 2004 WI Ltd Name
 The Phenomenon of Sound

REFLECTION
REFRACTION
DIFFRACTION

Copyright 2004 WI Ltd Name

 The Phenomenon of Sound

REFLECTION
REFRACTION
DIFFRACTION

Copyright 2004 WI Ltd Name

 Law of Reflection
Angle of Incidence = Angle of Reflection

60o 60o

Copyright 2004 WI Ltd Name

 Inclined incidence(not at o
90 )
Incident

Transmitted

The sound is refracted due to differences in

sound velocity in the 2 DIFFERENT materials
Copyright 2004 WI Ltd Name
 REFRACTION
Only occurs when:
The incident angle is other than 0

30

Water Steel Water

Steel Steel Steel

Refracted

Copyright 2004 WI Ltd Name

 REFRACTION
Only occurs when:
The incident angle is other than 0
The Two Materials has different
VELOCITIES

30
30

Steel Water

Steel Steel
65
30

No Refraction Refracted

Copyright 2004 WI Ltd Name

 Snells Law
Normal

Incident I
Material 1

Material 2 Refracted
R

Sine I Vel in Material 1

Sine R Vel in Material 2
Copyright 2004 WI Ltd Name
 Snells Law
C
20 Sine I Vel in Material 1

Sine R Vel in Material 2
Perspex
Sine 20 2730

Steel Sine 48.3 5960
48.3 0.4580 0.4580
C

Copyright 2004 WI Ltd Name

 Snells Law
Sine I Vel in Material 1
C
15
Sine R Vel in Material 2
Sine 15 2730
Perspex
Sine R 5960
Steel
5960
34.4 SinR Sin15
2730
C
SinR 0.565
R 34.4
Copyright 2004 WI Ltd Name
 Snells Law
C
20

Perspex

Steel
48.3

C
24
S

Copyright 2004 WI Ltd Name

 Snells Law
C
C When an incident beam of sound
approaches an interface of two
different materials:
REFRACTION occurs

Perspex
There may be more than one waveform
Steel transmitted into the second material,
example: Compression and Shear

When a waveform changes

into another waveform:
C MODE CHANGE
C
SS

Copyright 2004 WI Ltd Name

 Snells Law
If the angle of Incident is
C increased the angle of
refraction also increases

Up to a point where the

Compression Wave is at
Perspex 90 from the Normal

Steel 90 This happens at the

FIRST CRITICAL ANGLE

C
S

Copyright 2004 WI Ltd Name

 1st Critical Angle
C 27.4 Compression wave refracted
at 90 degrees

33

Copyright 2004 WI Ltd Name

 2nd Critical Angle
C
C
57

S (Surface Wave)
90

Shear wave refracted at 90 degrees

Shear wave becomes a surface wave

Copyright 2004 WI Ltd Name
 1st Critical Angle Calculation
C 27.2 Sine I 2730

Sine 90 5960
Perspex
Sin90 1
C
Steel 2730
SinI
5960
S SinI 0.458
I 27.26
Copyright 2004 WI Ltd Name
 2nd Critical Angle Calculation
C C Sine I 2730
57.4
Sine 90 3240
Perspex
Sin90 1
S
Steel 2730
SinI
3240
SinI 0.8425
I 57.4
Copyright 2004 WI Ltd Name
 Before the 1st. Critical Angle: There
1st. are both Compression and Shear
wave in the second material
C
At the FIRST CRITICAL ANGLE
2nd. Compression wave refracted at 90
Shear wave at 33 degrees in the
material

90 Between the 1st. And 2nd.

Beyond the 2nd. Critical Angle: Only SHEAR
Critical Angle: All wave in the material.
waves are reflected Compression is reflected out
out of the material. NO of the material.
wave in the material.
S C At the 2nd. Critical Angle: Shear
is refracted to 90 and become
33 SURFACE wave

Copyright 2004 WI Ltd Name

Copyright 2004 WI Ltd Name
 Summary
Standard angle probes between 1st and
2nd critical angles (45,60,70)
Stated angle is refracted angle in steel
No angle probe under 35, and more
than 80: to avoid being 2 waves in the
same material. One Defect Two Echoes

C S

Copyright 2004 WI Ltd Name

 Snells Law
Calculate the 1st critical angle for a
perspex/copper interface
V Comp perspex : 2730m/sec
V Comp copper : 4700m/sec

2730
SinI 0.5808 35.5
4700

Copyright 2004 WI Ltd Name