Scribd
Upload
254 views

Common Network Cables

This document summarizes different types of common network cables, including twisted pair, coaxial, and fiber optic cables. It describes key characteristics of each type such as bandwidth, size, connectors used, and factors that influence cable category ratings for twisted pair cables. The two basic types of twisted pair cables are UTP and STP, with STP providing better shielding from electrical noise. Coaxial cables like Thicknet and Thinnet were used for older 10 Mbps networks. Fiber optic cables can be multimode or single-mode, with single-mode capable of transmitting signals over greater distances.

Uploaded by

marlon felizardo
Copyright
© © All Rights Reserved
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
254 views

Common Network Cables

This document summarizes different types of common network cables, including twisted pair, coaxial, and fiber optic cables. It describes key characteristics of each type such as bandwidth, size, connectors used, and factors that influence cable category ratings for twisted pair cables. The two basic types of twisted pair cables are UTP and STP, with STP providing better shielding from electrical noise. Coaxial cables like Thicknet and Thinnet were used for older 10 Mbps networks. Fiber optic cables can be multimode or single-mode, with single-mode capable of transmitting signals over greater distances.

Uploaded by

marlon felizardo
Copyright
© © All Rights Reserved
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
You are on page 1/ 14

COMMON NETWORK

CABLES
Until recently, cables were the only
medium used to connect devices on
networks. A wide variety of networking
cables are available. These cables differ
in bandwidth, size, and cost. You need
to know what type of cable to use based
on the job requirements.
Twisted pair is a type of copper cabling
that is used for telephone
communications and most Ethernet
networks. A pair of wires forms a circuit
that transmits data. The pair is twisted
to provide protection against crosstalk,
the noise generated by adjacent pairs of
wires in the cable. Pairs of copper wires
are encased in color-coded plastic
insulation and are twisted together.

TWISTED PAIR
1. Unshielded twisted pair (UTP) is the
cable that has two or four pairs of wires.
This type of cable relies solely on the
cancellation effect produced by the twisted-
wire pairs that limits signal degradation
caused by electromagnetic interface (EMI)
and radio frequency interference (RFI).

THE TWO BASIC TYPES OF


TWISTED-PAIR CABLES ARE AS
FOLLOWS:
2. Shielded twisted pair (STP), each
pair of wire is wrapped in metallic foil to
better shield the wires from noise. Four
pairs of wires are then wrapped in an
overall metallic braid or foil. STP
reduces electrical noise from within the
cable. It also reduces EMI and RFI from
outside the cable.
Category Rating
UTP comes in several categories that are
based on two factors:
 The number of wires in the cable
 The number of twists in those wires
1. Category 3 is the wiring used for
telephone systems and Ethernet LAN at 10
Mega byte per second (Mbps).
2. Category 3 has four pairs of wires.
3. Category 5 and Category 5e have four pairs
of wires with a transmission rate of 100 Mbps.
4. Category 5 and Category 5e is the most
common network cables used.
5. Category 5e has more twists per foot than
Category 5 wiring.
6. Category 6 cables use a plastic divider to
separate the pairs of wires, which prevents
interference. The pairs also have more twists
than Category 5e cable.
Coaxial cable is a copper-cored cable
surrounded by a heavy shielding.
Coaxial cable is used to connect the
computers to the rest of the network.
Coaxial cable uses “British Naval
Connectors (BNC)” or “Bayonet Neill-
Concelman” connectors, at the ends of
the cables to make the connection.

COAXIAL CABLE
TYPES OF COAXIAL CABLE
a) Thicknet (10BASE5) is a coaxial cable used in
networks operating at 10 Mbps, with a maximum
length of 500 meters.
b)Thinnet (10BASE2) is a coaxial cable used in
networks operating at 10 Mbps, with a maximum
length of 185 meters.
c) RG-59 is most commonly used for cable television
in the U.S.
d)RG-6is higher-quality cable than RG-59, with more
bandwidth and less susceptibility to interference.
An optical fiber is a glass or plastic
conductor that transmits information
using light. Fiber optic cable has one
or more optical fibers enclosed in a
sheath or jacket. Because it is made of
glass, fiber-optic cable is not affected by
EMI or RFI. All signals are converted to
light pulses to enter the cable and are
converted back into electrical signals
when they leave it.
FIBER-OPTIC CABLE
TWO TYPES OF GLASS FIBER-OPTIC
CABLE:

a) Multimode is the cable that has a thicker core


than single-mode cable. It is easier to make, can
use simpler light sources such as Light Emitting
Diodes (LEDs), and works well over distances of a
few kilometers or less.
b) Single-mode is the cable that has a very thin
core. It is harder to make, uses lasers as a light
source, and can transmit signals dozens of
kilometers with ease.

You might also like