Scribd
Upload
63 views

227 Questions - General

This document contains a recitation on general materials science topics including: 1) Questions about the properties of different materials like aluminum alloys and polymers under various conditions like cold working. 2) Questions about ordering materials from strongest to weakest and identifying properties like whether a material is a composite. 3) Questions about matching materials to their applications and identifying materials based on properties like density and degree of crystallization. 4) Additional questions about concepts like the effect of cross-linking and molecular weight on melting point of polymers, methods for measuring ductility, and determining yield stress.

Uploaded by

Berke Bayrı
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
63 views

227 Questions - General

This document contains a recitation on general materials science topics including: 1) Questions about the properties of different materials like aluminum alloys and polymers under various conditions like cold working. 2) Questions about ordering materials from strongest to weakest and identifying properties like whether a material is a composite. 3) Questions about matching materials to their applications and identifying materials based on properties like density and degree of crystallization. 4) Additional questions about concepts like the effect of cross-linking and molecular weight on melting point of polymers, methods for measuring ductility, and determining yield stress.

Uploaded by

Berke Bayrı
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
You are on page 1/ 6

RECITATION GENERAL I

Prof.Dr. Bilgehan Ögel


 Which material below has the highest UTS?
a. Pure Al
b. Al-4%Mg Alloy 20%Cold Worked
c. Polyethylene string 30%CW.

 You are given two different Al Alloys:


a. Al-4%Mg alloy 40%Cold worked
b. Al-4%Mg alloy 40%Cold worked and then heated to 470C
If a tensile test is done, which alloy would yield a higher UTS?

 Which alloy given below has the highest charpy impact toughness?
a) Al-4%Mg alloy (in as-cast condition)
b) Al-4%Mg alloy (in hot rolled condition)
c) Al-4%Mg alloy (The hot rolled plate is taken and then 40%CW by
cold rolling)

Prof.Dr. Bilgehan Ögel 2


 Put the following materials in the order of increasing strength
a) Al alloy having a hardness of 125HB
b) Al alloy having a hardness of 110HB
c) Al alloy having a hardness of 80HB

 Put the following materials in the order of increasing strength


a) Pure Al
b) Polyethylene 20% recrystallized
c) Polyethylene 40% recrystallized
d) Steel

 Which of the following are made of composite? (Write Y or N)


a) Helical spring of a car _____
b) Concrete drilling bits (cutting tools) ____
c) Sea Shell ____
d) Polyester sailing boat main body ____
e) Al can for soft drinks ____

Prof.Dr. Bilgehan Ögel 3


 You are given two different type of PET polymer. Their densities are
measured and the following data is found:
PET (marked as A) 1.30gm/cc
PET (marked as B) 1.50gm/cc
One of them is amorphous, whereas one of them is 35% crystallized.
The PET marked as ____ is 35% crystallized. Because ________
_______________________________________________________
_________________________________________________________
_______________

 Al-5%Cu alloy is a composite? T F

Prof.Dr. Bilgehan Ögel 4


 In one column there are several materials and in the other column
applications are given. Find the best match (An example is given).

Material Application
A HDPE The gray waste water pipes in houses
A steel having very high hardness: The steel will be used as an elevator
B
650HV cable
A steel with σY=250MPa,
C Plastic shopping bags
UTS=400MPa and %el=32%
The material will be used to drill the
D Kevlar
steel sheets.
A steel with σY =1600MPa,
E Parachute ropes
UTS=1800MPa and %el=8%
F PVC Car tyre
G Polyethylene

H Butadiene-styrene copolymer

Prof.Dr. Bilgehan Ögel 5


 Which of the following have a higher melting point?
a) Polymer A which has a molecular weight of 100.000gm/mole and
10% of the available sites are cross-linked
b) Polymer B which has a molecular weight of 100.000gm/mole and
20% of the available sites are cross-linked

 A square cross-section bar will be bend to an angle of 90°. The


ductility of the alloy is of prime importance for this application. In
order to select the most ductile metal among many alloys present in
the stock, I would apply a _____________________ testing method
to measure ductility. Because _______________________
___________________________________________
 Several alloys show a well-defined yield point, i.e. the slope of -
changes suddenly. However, several others dont. For these alloys,
we use __________________ method, in order to find the yield
stress.

Prof.Dr. Bilgehan Ögel 6

You might also like