Chapter 6:

Mechanical Properties
ISSUES TO ADDRESS...

• Stress and strain

• Elastic behavior

• Plastic behavior

• Toughness, hardness and ductility

Chapter 6 - 1
 Elastic Deformation
1. Initial 2. Small load 3. Unload

bonds
stretch

return to
initial
d
F
F Linear-
elastic
Elastic means reversible! Non-Linear-
elastic
d
Chapter 6 - 2
 Plastic Deformation
1. Initial 2. Load 3. Unload
bonds
stretch planes
& planes still
shear sheared

dplastic
delastic + plastic

F
F
Plastic means permanent! linear linear
elastic elastic
d
dplastic
Chapter 6 - 3
 Engineering Stress
• Tensile stress, s: • Shear stress, t:
Ft Ft F

Area, A Area, A Fs

Fs
Ft
Fs Ft
Ft lb f N t= F
s= = 2 or 2
Ao
Ao in m
original area
before loading
 Stress has units:
N/m2 or lbf/in2
Chapter 6 - 4
Principal Ways to Apply Load

Chapter 6 - 5
 Engineering Strain
• Tensile strain: • Lateral strain:
d/2
-dL
e = d eL =
Lo Lo wo
wo

dL /2
• Shear strain:
q
x g = x/y = tan q

y 90º - q
Strain is always
90º dimensionless.
Adapted from Fig. 6.1 (a) and (c), Callister 7e. Chapter 6 - 6
 Stress-Strain Testing
• Typical tensile test • Typical tensile
machine specimen

Adapted from
extensometer specimen Fig. 6.2,
Callister 7e.

gauge
length

Adapted from Fig. 6.3, Callister 7e. (Fig. 6.3 is taken from H.W.
Hayden, W.G. Moffatt, and J. Wulff, The Structure and Properties of
Materials, Vol. III, Mechanical Behavior, p. 2, John Wiley and Sons,
New York, 1965.) Chapter 6 - 7
 Linear Elastic Properties
• Modulus of Elasticity, E:
(also known as Young's modulus)

• Hooke's Law:
s=Ee s F
E

e
Linear-
elastic F
simple
tension
test

Chapter 6 - 8
 Problem 1
• A cylindrical rod of Aluminum (E = 70
GPa) is to be subjected to a load of 9000
N. If the deformation is entirely elastic,
what must the diameter be to allow an
elongation of 1.50mm in a length of
500mm? (in mm)

Chapter 6 - 9
 Poisson's ratio, n
• Poisson's ratio, n:

eL
n=- e

metals: n ~ 0.33
ceramics: n ~ 0.25
polymers: n ~ 0.40

Units:
E: [GPa] or [psi]
n: dimensionless

Chapter 6 - 10
 Problem 2
• A cylindrical rod of steel (E = 207 GPa),
4mm in diameter is to be deformed by a
tensile force. Determine the force (in N)
that will produce an elastic reduction of
2.5 x 10-3mm in diameter if Poisson’s
ratio is 0.30.

Chapter 6 - 11
 Young’s Moduli: Comparison
Graphite
Metals Composites
Ceramics Polymers
Alloys /fibers
Semicond
1200
1000 Diamond
800
600
Si carbide
400 Tungsten Al oxide Carbon fibers only
Molybdenum Si nitride
E(GPa) 200
Steel, Ni
Tantalum <111>
CFRE(|| fibers)*
Platinum Si crystal
Cu alloys <100> Aramid fibers only
100 Zinc, Ti
80 Silver, Gold
Glass -soda AFRE(|| fibers)* Based on data in Table B2,
Aluminum Glass fibers only
60
40
Magnesium,
Tin GFRE(|| fibers)* Callister 7e.
Concrete Composite data based on
109 Pa 20 GFRE*
CFRE*
reinforced epoxy with 60 vol%
of aligned
Graphite GFRE( fibers)*
10 carbon (CFRE),
8 CFRE( fibers) *
6 AFRE( fibers) *
aramid (AFRE), or
Polyester glass (GFRE)
4 PET
PS fibers.
PC Epoxy only
2
PP
1 HDPE
0.8
0.6 Wood( grain)
PTFE
0.4

0.2 LDPE Chapter 6 - 12

 Useful Linear Elastic Relationships
• Simple tension:
d = FL o d = -n Fw o
L
EA o EA o
F
d/2
Ao
Lo
wo

dL /2
• Material, geometric, and loading parameters all
contribute to deflection.
• Larger elastic moduli minimize elastic deflection.
Chapter 6 - 13
 Plastic (Permanent) Deformation

• Simple tension test:

Elastic+Plastic
engineering stress, s at larger stress

Elastic
initially
permanent (plastic)
after load is removed

ep engineering strain, e

plastic strain Adapted from Fig. 6.10 (a),

Callister 7e.

Chapter 6 - 14
 Yield Strength, sy
• Stress at which noticeable plastic deformation has
occurred.
when ep = 0.002
tensile stress, s
sy

engineering strain, e
ep = 0.002 Adapted from Fig. 6.10 (a),
Callister 7e.
Chapter 6 - 15
 Yield Strength : Comparison
Graphite/
Metals/ Composites/
Ceramics/ Polymers
Alloys fibers
Semicond
2000
Steel (4140) qt

1000
Yield strength, sy (MPa)

Ti (5Al-2.5Sn) a

in ceramic matrix and epoxy matrix composites, since

700 W (pure)

since in tension, fracture usually occurs before yield.

in tension, fracture usually occurs before yield.

600 Cu (71500) cw
500 Mo (pure)
400 Steel (4140) a
Steel (1020) cd
300
Room T values
Hard to measure ,

Hard to measure,
Al (6061) ag
200 Steel (1020) hr ¨
Ti (pure) a
Ta (pure)
Cu (71500) hr Based on data in Table B4,
Callister 7e.
100 a = annealed
dry
70 PC
hr = hot rolled
60 Al (6061) a Nylon 6,6 ag = aged
50 PET
cd = cold drawn
40 PVC humid
cw = cold worked
PP
30 HDPE qt = quenched & tempered

20

LDPE
Tin (pure) Chapter 6 - 16
10
 Tensile Strength, TS
• Maximum stress on engineering stress-strain curve.
Adapted from Fig. 6.11,
Callister 7e.
TS
F = fracture or
sy
ultimate
engineering

strength
stress

Typical response of a metal

Neck – acts
as stress
concentrator
strain
engineering strain
• Metals: occurs when noticeable necking starts.
• Polymers: occurs when polymer backbone chains are
aligned and about to break.
Chapter 6 - 17
 Tensile Strength : Comparison
Graphite/
Metals/ Composites/
Ceramics/ Polymers
Alloys fibers
Semicond
5000 C fibers
Aramid fib
3000 E-glass fib
Tensile strength, TS (MPa)

2000 Steel (4140) qt

AFRE(|| fiber)
1000 W (pure) Diamond GFRE(|| fiber)
Ti (5Al-2.5Sn)aa CFRE(|| fiber)
Steel (4140)
Cu (71500) cw Si nitride
Cu (71500) hr Al oxide
Steel (1020)
300 ag
Al (6061) a
Ti (pure)
200 Ta (pure) Room Temp. values
Al (6061) a
100 Si crystal wood(|| fiber) Based on data in Table B4,
<100> Nylon 6,6
Glass-soda PC PET Callister 7e.
40 Concrete PVC GFRE( fiber) a = annealed
PP CFRE( fiber)
30 hr = hot rolled
AFRE( fiber)
HDPE ag = aged
20 Graphite
LDPE cd = cold drawn
cw = cold worked
10 qt = quenched & tempered
AFRE, GFRE, & CFRE =
aramid, glass, & carbon
fiber-reinforced epoxy
wood ( fiber)
composites, with 60 vol%
fibers.
1 Chapter 6 - 18
 Ductility
Lf - Lo
• Plastic tensile strain at failure: %EL = x 100
Lo
smaller %EL
Engineering
tensile
stress, s larger %EL Ao
Lo Af Lf
Adapted from Fig. 6.13,
Callister 7e.

Engineering tensile strain, e

• Another ductility measure: Ao - Af

%RA = x 100
Ao

Chapter 6 - 19
 Toughness
• Energy to break a unit volume of material
• Approximate by the area under the stress-strain
curve.
Engineering small toughness (ceramics)
tensile large toughness (metals)
stress, s
Adapted from Fig. 6.13, very small toughness
Callister 7e. (unreinforced polymers)

Engineering tensile strain, e

Brittle fracture: elastic energy

Ductile fracture: elastic + plastic energy
Chapter 6 - 20
 Resilience, Ur
• Ability of a material to store energy
– Energy stored best in elastic region

1
Ur @ sy e y
2

Adapted from Fig. 6.15,

Callister 7e.
Chapter 6 - 21
 Problem 3
• Steel springs must have a modulus of
resilience of at least 2.0 MPa. What
should be the minimum yield strength (in
MPa) of a 10mm diameter spring used to
support a load of 10,000 N if elongation is
1mm for every 100mm length?

Chapter 6 - 22
 Hardness
• Resistance to permanently indenting the surface.
• Large hardness means:
--resistance to plastic deformation or cracking in
compression.
--better wear properties.
apply known force measure size
e.g., of indent after
10 mm sphere removing load

Smaller indents
D d mean larger
hardness.

most brasses easy to machine cutting nitrided

plastics Al alloys steels file hard tools steels diamond

increasing hardness
Chapter 6 - 23
 Hardness: Measurement
Table 6.5

Chapter 6 - 24
 True Stress & Strain
Note: S.A. changes when sample stretched

• True stress sT = F Ai sT = s1  e 

• True Strain eT = ln i  o  eT = ln1  e 

Adapted from Fig. 6.16,

Callister 7e.

Chapter 6 - 25
 Design or Safety Factors
• Design uncertainties mean we do not push the limit.
• Factor of safety, N Often N is
sy between
sworking = 1.2 and 4
N
• Example: Calculate a diameter, d, to ensure that yield does
not occur in the 1045 carbon steel rod below. Use a
factor of safety of 5.
d
sy
sworking = 1045 plain
carbon steel:
N sy = 310 MPa Lo
220,000N 5 TS = 565 MPa

 d2 / 4
F = 220,000N
d = 0.067 m = 6.7 cm
Chapter 6 - 26
 Summary
• Stress and strain: These are size-independent
measures of load and displacement, respectively.
• Elastic behavior: This reversible behavior often
shows a linear relation between stress and strain.
To minimize deformation, select a material with a
large elastic modulus (E or G).
• Plastic behavior: This permanent deformation
behavior occurs when the tensile (or compressive)
uniaxial stress reaches sy.
• Toughness: The energy needed to break a unit
volume of material.
• Ductility: The plastic strain at failure.

Chapter 6 - 27
 ANNOUNCEMENTS
Reading:

Core Problems:

Self-help Problems:

Chapter 6 - 28