Scribd
Upload
154 views

Casting

Uploaded by

Farhan Khan
Copyright
© © All Rights Reserved
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
154 views

Casting

Uploaded by

Farhan Khan
Copyright
© © All Rights Reserved
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
You are on page 1/ 12

General Defects: Misrun

A casting that has solidified before completely


filling mold cavity

Causes:
1.Insufficient fluidity
2.Low pouring Temp
3.Pouring done too slowly
4.Cross section area of cavity is
too small

Figure 11.22 Some common defects in castings: (a) misrun


©2007 John Wiley & Sons, Inc. M P Groover, Fundamentals of Modern Manufacturing 3/e
General Defects: Cold Shot
Metal splatters during pouring and solid globules
form and become entrapped in casting

Causes:

1.Inadequate pouring procedures


and gating systems design.

Figure 11.22 Some common defects in castings: (c) cold shot

©2007 John Wiley & Sons, Inc. M P Groover, Fundamentals of Modern Manufacturing 3/e
Nonferrous Casting Alloys: Aluminum
 Generally considered to be very castable
 Pouring temperatures low due to low melting
temperature of aluminum
 Tm = 660C (1220F)
 Properties:
 Light weight
 Range of strength properties by heat treatment
 Easy to machine

©2007 John Wiley & Sons, Inc. M P Groover, Fundamentals of Modern Manufacturing 3/e
Nonferrous Casting Alloys: Copper
Alloys
 Includes bronze, brass, and aluminum bronze
 Properties:
 Corrosion resistance
 Attractive appearance
 Good bearing qualities
 Applications: pipe fittings, marine propeller
blades, pump components, ornamental jewelry

©2007 John Wiley & Sons, Inc. M P Groover, Fundamentals of Modern Manufacturing 3/e
Nonferrous Casting Alloys: Zinc Alloys
 Highly castable, commonly used in die casting
 Low melting point – melting point of zinc Tm =
419C (786F)
 Good fluidity for ease of casting
 Properties:
 Low creep strength, so castings cannot be
subjected to prolonged high stresses

©2007 John Wiley & Sons, Inc. M P Groover, Fundamentals of Modern Manufacturing 3/e
Metal Casting Processes
1. Sand Casting
2. Other Expendable Mold Casting Processes
3. Permanent Mold Casting Processes
4. Foundry Practice
5. Casting Quality
6. Metals for Casting
7. Product Design Considerations

©2007 John Wiley & Sons, Inc. M P Groover, Fundamentals of Modern Manufacturing 3/e
Product Design Considerations
 Geometric simplicity:
 Although casting can be used to produce
complex part geometries, simplifying the
part design usually improves castability
 Avoiding unnecessary complexities:
 Simplifies mold‑making
 Reduces the need for cores
 Improves the strength of the casting

©2007 John Wiley & Sons, Inc. M P Groover, Fundamentals of Modern Manufacturing 3/e
Product Design Considerations
 Corners on the casting:
 Sharp corners and angles should be
avoided, since they are sources of stress
concentrations and may cause cracks
 Generous fillets should be designed on
inside corners and sharp edges should be
blended

©2007 John Wiley & Sons, Inc. M P Groover, Fundamentals of Modern Manufacturing 3/e
Product Design Considerations
 Draft Guidelines:
 In expendable mold casting, draft facilitates
removal of pattern from mold
 Draft = 1 for sand casting
 In permanent mold casting, purpose is to aid
in removal of the part from the mold
 Draft = 2 to 3 for permanent mold
processes
 Similar tapers should be allowed if solid cores
are used

©2007 John Wiley & Sons, Inc. M P Groover, Fundamentals of Modern Manufacturing 3/e
Draft
 Minor changes in part design can reduce need
for coring

Figure 11.25 Design change to eliminate the need for using


a core: (a) original design, and (b) redesign

©2007 John Wiley & Sons, Inc. M P Groover, Fundamentals of Modern Manufacturing 3/e
Product Design Considerations
 Dimensional Tolerances and Surface Finish:
 Significant differences in dimensional
accuracies and finishes can be achieved in
castings, depending on process:
 Poor dimensional accuracies and finish for
sand casting
 Good dimensional accuracies and finish for
die casting and investment casting

©2007 John Wiley & Sons, Inc. M P Groover, Fundamentals of Modern Manufacturing 3/e
Product Design Considerations
 Machining Allowances:
 Almost all sand castings must be machined
to achieve the required dimensions and part
features
 Additional material, called the machining
allowance, is left on the casting in those
surfaces where machining is necessary
 Typical machining allowances for sand
castings are around 1.5 and 3 mm (1/16 and
1/4 in)

©2007 John Wiley & Sons, Inc. M P Groover, Fundamentals of Modern Manufacturing 3/e

You might also like