TRANSPORTATION ENGINEERING-II

Lecture-9
Rigid Pavement Design

Muhammad Usman Haider

Lecturer
Email:
[email protected]
 MODES OF TRANSPORTATION

• Basic mode of transportation are

 Land
• Roadway
• railway
 Water
 Air
 MODES OF TRANSPORTATION
• Highways
Car, Bus, Truck, non- motorized ..etc
• Railways
Passenger and Goods
• Airways
Aircraft and Helicopters
• Waterways
Ships, boats…
• Continuous Flow systems
Pipelines,belts,elevetor,ropeway…etc.
• Merits and Demerits: Based on accessibility, mobility, cost, tonnage..
 Highways
• It gives the maximum service to one and all
• It gives maximum flexibility for travel with reference
to route, direction, time and speed of travel
• It provide door to door service
• Other modes are depend on it
• It requires small investment for the government
• Motor vehicles are cheaper than other carriers like
rail locomotive and wagons
• It saves the time for short distance
• High degree of accident due to flexibility
of movement
 Characteristics of road transport
• Roads are used by various types of road vehicles,
like passenger cars, buses, trucks, pedal cycle and
animal drawn vehicle.
• It requires a relatively small investment for the
government.
• It offers a complete freedom to road users to
transfer the vehicle from one lane to another and
from one road to another according to need and
convenience.
• Speed and movement is directly related with the
severity of accident.
• Road transport is the only means of transport that
offers itself to the whole community alike.
 HISTORICAL DEVELOPMENT OF ROAD
CONSTRUCTION
• Oldest mode
 Foot paths- animal ways, cart path……..
• As civilization evolved the need for transportation
increased
ROMAN ROAD-(500 B.C.)
 They were built straight regardless of gradient
 They were built after the soft soil was removed and
a hard stratum was reached.
 Thickness varies from 0.75 m to 1.2m
Roman Road Construction
Basic cross section
 Modern Highway
Roman Roads
 Other oldest road transport are

• Tresaguet construction

• Metcalf construction

• Telford construction

• Mecadam construction
 Classification of Highways
Depending on weather
 All weather roads
 Fair weather roads

Depending the type of Carriage way

 Paved roads(WBM)
 Unpaved roads(earth road or gravel road)

Depending upon the pavement surface

 Surfaced roads(bituminous or cement
concrete road)
 Un surfaced roads
 Classification of Highways
Based on the Traffic Volume
 Heavy
 Medium
 Light

Based on Load or Tonnage

Class 1 or Class 2 etc or Class A , B etc Tonnes
per day

Based on location and function ( Nagpur road plan )

 National highway (NH)
 State highway (SH)
 Major district road (MDR)
 Other district road (ODR)
 Village road (VR)
 Based on modified system of
Highways classification
• Primary
 Expressways
 National Highways

• Secondary
 SH
 MDR

• Tertiary
 ODR
 VR
 Urban Road Classification

• Arterial Roads
• Sub Arterial
• Collector
• Local Street
• Cul-de-sac
• Pathway
• Driveway
 ARTERIAL

• No frontage access, no standing vehicle,

very little cross traffic.
• Design Speed : 80km/hr
• Land width : 50 – 60m
• Divided roads with full or partial parking
• Pedestrian allowed to walk only at
intersection
 SUB ARTERIAL ROAD
• Bus stops but no standing vehicle.
• Less mobility than arterial.
• Spacing for CBD : 0.5km
• Design speed : 60 km/hr
• Land width : 30 – 40 m
 Collector Street
• Collects and distributes traffic from local
streets
• Provides access to arterial roads
• Located in residential, business
and industrial areas.
• Full access allowed.
• Parking permitted.
• Design speed : 50km/hr
• Land Width : 20-30m
 Local Street

• Design Speed : 30km/hr.

• Land Width : 10 – 20m.
• Primary access to residence, business or
other abutting property
• Less volume of traffic at slow speed
• Unrestricted parking, pedestrian
movements. (with frontage access, parked
vehicle, bus stops and no waiting
restrictions)
 CUL–DE- SAC
• Dead End Street with only one entry
access for entry and exit.
• Recommended in Residential areas
 Driveway

• A driveway is a type of private road for local

access to one or a small group of structures, and
is owned and maintained by an individual or
group.
• Driveways are commonly used as paths to
private garages, fuel stations, or houses
 PAVEME
• pavement isNT
the durable surface material
laid down on an area intended to sustain
vehicular load or foot traffic, such as a road or
walkway.
• It is of two types
Flexible pavement or bituminous pavement
or black top pavement
Rigid pavement or cement concrete
pavement or white surface pavement
 COMPARISON OF FLEXIBLE PAVEMENT & RIGID PAVEMENT
FLEXIBLE PAVEMENT RIGID
1. HavePAVEMENT
low flexural strength 1. Have more flexural strength
2. Load is transferred by grain to 2. No such phenomenon of grain
grain contact to grain load transfer exists
3. Surfacing cannot be laid directly 3. Surfacing can be directly laid
on the sub grade but a sub on
base is needed the sub grade
4. No thermal stresses are induced 4. Thermal stresses are induced
5. expansion joints are not needed 5. expansion joints are needed
6. Design life 10-15 years 6. Design life 20-30 years
7. Initial cost of construction is low 7. Initial cost of construction is
8. Maintenance cost is high high
9. Road can be used for traffic 8. Less maintenance cost
within 24 hours 9. Road cannot be used until 14
10. Damaged by Oils and Certain days
10. No of curing
Damage by Oils and other
Chemicals chemicals
Rigid Pavement
 Flexible
pavement Rigid
pavement
 Requirements of a
• Sufficientpavement
thickness to distribute the wheel load stresses to
a safe value on the sub-grade soil.
• Structurally strong to withstand all types of stresses
imposed upon it.
• Adequate coefficient of friction to prevent skidding of
vehicles.
• Smooth surface to provide comfort to road users even at
high speed.
• Produce least noise from moving vehicles.
• Dust proof surface so that traffic safety is not impaired by
reducing visibility.
• Impervious surface, so that sub-grade soil is well
protected.
• Long design life with low maintenance cost.
Distribution of pressure
 Types of flexible
• pavements
Conventional layered flexible pavement
• Full - depth asphalt pavement
• Contained rock asphalt mat (CRAM).
• Conventional flexible pavements are layered systems
with high quality expensive materials are placed in the top
where stresses are high, and low quality cheap materials
are placed in lower layers.
• Full - depth asphalt pavements are constructed by
placing bituminous layers directly on the soil sub-grade.
This is more suitable when there is high traffic and local
materials are not available.
• Contained rock asphalt mats are constructed by
placing dense/open graded aggregate layers in between
two asphalt layers.
c/s of flexible
pavement

c/s of rigid
c/s of flexible pavement

Load is transferred by grain to grain contact

 Typical layers of a flexible
pavement
Seal Coat: Seal coat is a thin surface treatment used to water-
proof the surface and to provide skid resistance and to seal the
surfacing against the ingress of water.
Tack Coat: Tack coat is a very light application of asphalt, usually
asphalt emulsion diluted with water. It provides proper bonding
between two layer of binder course.it is generally applied on
impervious surface.
Prime Coat: Prime coat is an application of low viscous liquide
bituminous material over an existing porous or absorbent
pavement surface like WBM.
• Prime objective is to plug the capillary voids of the porous
surface and to bond the loose materials on the existing surface
like granular bases on which binder layer is placed. It provides
bonding between two layers.
Prime
coat
Seal coat
 Typical layers of a flexible
pavement
Surface course:
• Surface course is the layer directly in contact with traffic
loads and generally contains superior quality materials.
They are usually constructed with dense graded asphalt
concrete(AC).
• It provides characteristics such as friction, smoothness,
drainage, etc. Also it will prevent the entrance of
excessive quantities of surface water into the underlying
base, sub-base and sub-grade,
• It provide a smooth and skid- resistant riding surface,
• It must be water proof to protect the entire base and
sub-grade from the weakening effect of water.
 Typical layers of a flexible
pavement
Binder course:
• This layer provides the bulk of the asphalt concrete structure.
It's chief purpose is to distribute load to the base course.
• The binder course generally consists of aggregates having
less asphalt and doesn't require quality as high as the surface
course, so replacing a part of the surface course by the binder
course results in more economical design.
Base course:
• The base course is the layer of material immediately beneath
the surface of binder course and it provides additional load
distribution and contributes to the sub-surface drainage It may
be composed of crushed stone and other untreated or
stabilized materials.
 Typical layers of a flexible
• pavement
Sub-Base course: The sub-base course is the layer
of material beneath the base course and the
primary functions are to provide structural support,
improve drainage.
• It may WBM or WMM
• A sub-base course is not always needed or used. For
example, a pavement constructed over a high quality.
• Sub-grade: The top soil or sub-grade is a layer of natural
soil prepared to receive the stresses from the layers above.
It is essential that at no time soil sub-grade is
overstressed.
• It should be compacted to the desirable density, near
the optimum moisture content.
 Types of Rigid
Pavements
• Jointed plain concrete pavement (JPCP),
• Jointed reinforced concrete pavement (JRCP),
• Continuous reinforced concrete pavement
(CRCP)
• Pre-stressed concrete pavement (PCP).
 Types of Rigid
• JointedPavements
Plain Concrete Pavement: constructed with
closely spaced contraction joints. Dowel bars or aggregate
interlocks are normally used for load transfer across joints.
They normally has a joint spacing of 5 to 10m.
• Jointed Reinforced Concrete Pavement: reinforcements
do not improve the structural capacity significantly but
they can drastically increase the joint spacing to 10 to
30m. Dowel bars are required for load transfer.
Reinforcements help to keep the slab together even after
cracks.
• Continuous Reinforced Concrete Pavement: Complete
elimination of joints are achieved by reinforcement.
 Rigid
pavement

Transver
se
joint
Granular
materials
FLEXIBLE PAVEMENT RIGID PAVEMENT
Types of Pavements
Wheel Load Distribution
Flexible Rigid
• Jointed Plain Concrete Pavement
(JPCP)
LOAD DISTRIBUTION
Components of Flexible Pavement