Chapter(7)

LTE(Long Term Evolution)

Radio Access
 Introduction
• LTE was initiated in late 2004 with the overall aim of providing a new radio
access technology focusing on packet-switched data only.
• The first phase of the 3GPP(Generation Partnership Project) work on LTE was
to define a set of performance and capability targets for LTE.
• This included targets on peak data rates, user/system throughput, spectral
efficiency, and control/user-plane latency.
• Requirements were also set on spectrum flexibility, as well as on
interaction/compatibility with other 3GPP radio-access technologies
(GSM(Global System for Mobile Communications), WCDMA(Wideband Code
Division Multiple Access)/HSPA(high speed packet access), and TD-
SCDMA(Time Division Synchronous Code Division Multiple Access)).
• 3GPP studies on the feasibility of different technical solutions considered for
LTE were followed by development of detailed specifications.
 Con't d
• In parallel to the development of LTE, there has also been an evolution of
the overall 3GPP network architecture, termed System Architecture
Evolution (SAE), including both the radio access network and the core
network.
• Requirements were also set on the architecture evolution, leading to a
new flat radio-access-network architecture with a single type of node, the
eNodeB(Evolved Node B) as well as a new core-network architecture.
• An excellent description of the LTE-associated core-network architecture,
the Evolved Packet Core (EPC).
 7.1.1 Transmission scheme
• The LTE downlink transmission scheme is based on conventional OFDM.
• OFDM(Orthogonal frequency-division multiplexing) provides a high degree
of robustness against channel frequency selectivity.
• Although signal corruption due to a frequency-selective channel can, in
principle, be handled by equalization at the receiver side, the complexity of
such equalization starts to become unattractively high for implementation
in a terminal at larger bandwidths and especially in combination with
advanced multi-antenna transmission schemes such as spatial
multiplexing.
• Therefore, OFDM is an attractive choice for LTE for which a wide
bandwidth and support for advanced multi-antenna transmission were key
requirements.
 Con't d
• OFDM also provides some additional benefits relevant for LTE:
• OFDM provides access to the frequency domain, thereby enabling an
additional degree of freedom to the channel-dependent scheduler
compared to time-domain-only scheduling used in major 3G systems.
• Flexible transmission bandwidth to support operation in spectrum
allocations of different sizes is straightforward with OFDM, at least from a
baseband perspective, by varying the number of OFDM subcarriers used for
transmission.
• Broadcast/multicast transmission, where the same information is
transmitted from multiple base stations, is straightforward with OFDM.
• The LTE uplink is also based on OFDM transmission.
• However, different means are taken to reduce the cubic metric of uplink
transmissions, thereby enabling higher power-amplifier efficiency on the
terminal side.
 Con’t d
• The LTE uplink transmission scheme should be described as OFDM with
different techniques, including DFT precoding for data transmission, being
used to reduce the cubic metric of the transmitted signal.
• The use of OFDM transmission for the LTE uplink allows for orthogonal
separation of uplink transmissions also in the frequency domain.
• Orthogonal separation is in many cases beneficial as it avoids interference
between uplink transmissions from different terminals within the cell
(intra-cell interference).
• The LTE uplink transmission scheme allows for both time division multiple
access (TDMA) and frequency division multiple access (FDMA) between
users.
 7.1.2 Channel-dependent scheduling and
rate adaptation
• At the core of the LTE transmission scheme is the use of shared-channel
transmission with the overall time–frequency resource dynamically shared
between users.
• The use of shared channel transmission is well matched to the rapidly
varying resource requirements posed by packet-data communication and
also enables several of the other key technologies on which LTE is based.
• The scheduler controls, for each time instant, to which users the different
parts of the shared resource should be assigned.
• The scheduler also determines the data rate to be used for each
transmission.
• Thus, rate adaptation can be seen as a part of the scheduling functionality.
• The scheduler is a key element and to a large extent determines the
overall system performance, especially in a highly loaded network.
• Both downlink and uplink transmissions are subject to tight scheduling in
LTE.
 Con’t d
• A substantial gain in system capacity can be achieved if the channel
conditions are taken into account in the scheduling decision, so-called
channel-dependent scheduling.
• Due to the use of OFDM in both the downlink and uplink transmission
directions, the scheduler has access to both the time and frequency
domains.
• In other words, the scheduler can, for each time instant and frequency
region, select the user with the best channel conditions.
• For LTE, scheduling decisions can be taken as often as once every 1 ms and
the granularity in the frequency domain is 180 kHz.
• This allows for relatively rapid channel variations in both the time and
frequency domains to be tracked and utilized by the scheduler.
 Con’t d
• Based on the channel-state reports, also referred to as channel-state
information(CSI), the downlink scheduler can assign resources for
downlink transmission to different terminals, taking the channel quality
into account in the scheduling decision.
• In principle, a scheduled terminal can be assigned an arbitrary
combination of 180 kHz wide resource blocks in each 1 ms scheduling
interval.
 7.1.3 Inter-cell interference coordination
• LTE is designed to operate with a one-cell frequency reuse, implying that
the same carrier frequency can be used at neighboring transmission
points.
• In particular, the basic control channels of LTE are designed to operate
properly with the relatively low signal-to interference ratio that may be
experienced in a reuse-one deployment.
• More specifically, the release-8 specifications defined a set of messages
that can be exchanged between eNodeBs using the so-called X2 interface.
• These messages provide information about the interference situation
experienced by the eNodeB issuing the message and can be used by a
neighboring eNodeB receiving the message as input to its scheduling
process, thereby providing a means for at least partly coordinating the
transmissions and controlling the interference between cells of different
eNodeBs.
 Con’td
• Especially severe interference situations may occur in so-called
heterogeneous network deployments consisting of overlapping layers of
base stations with large differences in the downlink transmission power.
 7.1.4 Hybrid ARQ with soft combining
• allows the terminal to rapidly request retransmissions of erroneously received transport
blocks
• provides a tool for implicit rate adaptation
• minimizes the impact on end-user performance from erroneously received packets
• uses Incremental redundancy
• buffers the soft bits at the receiver to be able to perform soft combining between
transmission attempts
• Chase combining:
– consist of the same set of coded bits as the original transmission
– maximum-ratio combination to combine each received channel bit with any previous
transmissions of the same bit, and the combined signal is fed to the decoder
• Incremental redundancy:
– each retransmission does not have to be identical to the original transmission
– uses a different set of coded bits than the previous transmission
– combines the retransmission with previous transmission attempts of the same packet at the
receiver
 7.1.5 Multi-antenna transmission
• 3 techniques: have different objectives, and are implemented in different ways
– Diversity processing:
• increases the received signal power and reduces the amount of fading by
using multiple antennas at the transmitter, the receiver or both
– Spatial multiplexing:  
• the transmitter and receiver both use multiple antennas so as to increase
the data rate
• described as the use of multiple input multiple output (MIMO) antennas
– Beamforming:
•  a base station uses the multiple antennas in a completely different way,
to improve the received SINR and to increase its coverage
 7.1.5 Multi-antenna transmission
• For uplink transmissions
– they have been used in many cellular systems for several years
• For downlink transmissions
• as dual receive antennas are the baseline for all LTE terminals, the
downlink performance is also improved
• receive diversity to collect additional energy and suppress fading
• additional gains can be achieved in interference-limited scenarios if the
antennas are used not only to provide diversity, but also to suppress
interference
 Spatial Multiplexing (MIMO)
• uses multiple antennas at both the transmitter and receiver
• results in an increased data rate, channel conditions permitting, in bandwidth-
limited scenarios by creating several parallel “channels,”.
• referred to as multi-user MIMO in 3GPP
• under control of the base station, which therefore can select a suitable scheme
for each transmission
• minimize errors and optimize data speed
• enable a variety of signal paths to carry the data, choosing separate paths for
each antenna to enable multiple signal paths to be used
Spatial Multiplexing (MIMO): Cont’d
 7.1.6 Spectrum flexibility
• A high degree of spectrum flexibility is one of the main characteristics of
the LTE radio access technology.
• The aim of this spectrum flexibility is to allow for the deployment of LTE
radio access in different frequency bands with various characteristics,
including different duplex arrangements and different sizes of the available
spectrum.
 7.1.6.1 Flexibility in duplex arrangements
• One important part of the LTE requirements in terms of spectrum
flexibility is the possibility to deploy LTE-based radio access in both paired
and unpaired spectrum.
• Therefore, LTE supports both frequency- and time-division-based duplex
arrangements.
• Frequency-Division Duplex (FDD), implies that downlink and uplink
transmission take place in different, sufficiently separated, frequency
bands.
• Time-Division Duplex (TDD), implies that downlink and uplink transmission
take place in different, non-overlapping time slots.
• Thus, TDD can operate in unpaired spectrum, whereas FDD requires
paired spectrum.
• The required flexibility and resulting requirements to support LTE
operation in different paired and unpaired frequency Arrangements.
 Con’t d
• Operation in both paired and unpaired spectrum has been supported by
3GPP radio-access technologies even before the introduction of LTE by
means of FDD-based WCDMA/HSPA in combination with TDD-based TD-
SCDMA radio.
• However, this was then achieved by means of, at least in the details,
relatively different radio-access technologies leading to additional effort
and complexity when developing and implementing dual-mode terminals
capable of both FDD and TDD operation.
• LTE, on the other hand, supports both FDD(frequency division duplexing)
and TDD(time division duplexing) within a single radio-access technology,
leading to a minimum of deviation between FDD and TDD for LTE-based
radio access.
• In half-duplex FDD, transmission and reception at a specific terminal are
separated in both frequency and time.
 Con’t d
• The base station still uses full-duplex FDD as it simultaneously may
schedule different terminals in uplink and downlink; this is similar to, for
example, GSM operation.
• The main benefit with half-duplex FDD is the reduced terminal complexity
as no duplex filter is needed in the terminal.
• This is especially beneficial in the case of multi-band terminals which
otherwise would need multiple sets of duplex filters.
 7.1.6.2 Bandwidth flexibility
• An important characteristic of LTE is the support for a range of different
transmission bandwidths on both downlink and uplink.
• The main reason for this is that the amount of spectrum available for LTE
deployment may vary significantly between different frequency bands and
also depending on the exact situation of the operator.
• LTE supports operation in a wide range of spectrum allocations, achieved
by a flexible transmission bandwidth being part of the LTE specifications.
• To efficiently support very high data rates when spectrum is available, a
wide transmission bandwidth is necessary.
• The maximum achievable data rates will be reduced accordingly.
• The spectrum flexibility is further improved in later releases of LTE.
 Con’t d
• The basic radio-access specification, including the physical-layer and
protocol specifications, allows for any transmission bandwidth ranging
from roughly 1 MHz up to around 20 MHz.
• At the same time, at an initial stage, radio frequency requirements are
only specified for a limited subset of transmission bandwidths,
corresponding to what is predicted to be relevant spectrum-allocation
sizes and relevant migration scenarios.
• Thus, in practice the LTE radio-access technology supports a limited set of
transmission bandwidths, but additional transmission bandwidths can
easily be introduced by updating only the RF specifications.
 7.2 LTE release 9
• After completing the first release of LTE, work continued in 3GPP with
introducing additional functionality in the second release of the LTE
specifications, release 9.
• The main new features introduced as part of release 9, completed in late
2009, were support for multicast transmission, support for network-
assisted positioning services, and enhancements to beam forming in the
downlink.
 7.2.1 Multicast and broadcast supports
• implies transmission of the same information from multiple cells
• uses signal power from multiple cell sites at the detection
• synchronizes the transmittion timing between the cells
• referred to as Multicast/Broadcast Single-Frequency Network (MBSFN)
transmission (in 3GPP)
• not only improve the received signal strength, but also eliminate the
inter-cell interference
• may eventually be limited by noise only and can then, in the case of small
cells, reach extremely high values (with OFDM)
• assumes the use of tight synchronization and time alignment of the signals
transmitted from different cell sites (with MBSFN)