Spread Spectrum

UNIT – 5
Presented by
Mrs. M.P.Sasirekha
 Spread Spectrum
• Spread spectrum communication systems are widely used
today in a variety of applications for different purposes such
as access of same radio spectrum by multiple users (multiple
access), anti-jamming capability (so that signal transmission
can not be interrupted or blocked by spurious transmission
from enemy), interference rejection, secure
communications, multi-path protection, etc.
 Spread Spectrum
• However, irrespective of the application, all spread spectrum
communication systems satisfy the following criteria-
• (i) As the name suggests, bandwidth of the transmitted signal is much
greater than that of the message that modulates a carrier.
• (ii) The transmission bandwidth is determined by a factor
independent of the message bandwidth.
• The power spectral density of the modulated signal is very low and
usually comparable to background noise and interference at the
receiver.
 Spread Spectrum
• A random spreading code sequence c(t) of chosen length is used to
‘spread’(multiply) the modulating signal m(t).
• Sometimes a high rate pseudo-noise code is used for the purpose of
spreading.
• Each bit of the spreading code is called a ‘chip’. Duration of a chip ( Tc)
is much smaller compared to the duration of an information bit ( T).
• Let us consider binary phase shift keying (BPSK) for modulating a
carrier by this spread signal.
• If m(t) represents a binary information bit sequence and c(t)
represents a binary spreading sequence, the ‘spreading’ or
multiplication operation reduces to modulo-2 or ex-or addition.
 Spread Spectrum
• For example, if the modulating signal m(t) is available at the rate of 10
Kbits per second and the spreading code c(t) is generated at the rate
of 1 Mbits per second, the spread signal d(t) is generated at the rate
of 1 Mega Chips per second.
• So, the null-to-null main lobe bandwidth of the spread signal is now 2
MHz.
• We say that bandwidth has been ‘spread’ by this operation by a factor
of hundred.
• This factor is known as the spreading gain or process gain (PG). The
process gain in a practical system is chosen based on the application
• On BPSK modulation, the spread signal becomes, s(t) = d(t).coswt.
Fig.7.38.1 (b) shows the baseband processing operations necessary
after carrier demodulation.
• Note that, at the receiver, the operation of despreading requires the
generation of the same spreading code incorrect phase with the
incoming code.
• The pseudo noise (PN) code synchronizing module detects the phase
of the incoming code sequence, mixed with the information sequence
and aligns the locally generated code sequence appropriately.
• After this important operation of code alignment (i.e. synchronization)
the received signal is ‘despread’ with the locally constructed
spreading code sequence.
• The dispreading operation results in a narrowband signal, modulated
by the information bits only.
• So, a conventional demodulator may be used to obtain the message
signal estimate.
 Advantages of spread spectrum
• Cross-talk elimination
• Better output with data integrity
• Reduced effect of multipath fading
• Better security
• Reduction in noise
• Co-existence with other systems
• Longer operative distances
• Hard to detect
• Not easy to demodulate/decode
• Difficult to jam the signals
 Types of SS
• Based on the kind of spreading modulation, spread spectrum systems
are broadly classified as-
• (i) Direct sequence spread spectrum (DS-SS) systems
• (ii) Frequency hopping spread spectrum (FH-SS) systems
• (iii) Time hopping spread spectrum (TH-SS) systems.
• (iv) Hybrid systems
 Direct Sequence (DS) Spread Spectrum
System (DSSS)
• The information signal in DSSS transmission is spread at baseband and
then the spread signal is modulated by a carrier in a second stage.
Following this approach, the process of modulation is separate from
the spreading operation.
• An important feature of DSSS system is its ability to operate in
presence of strong co-channel interference. A popular definition of
the processing gain (PG) of a DSSS system is the ratio of the signal
bandwidth to the message bandwidth.
 Direct Sequence (DS) Spread Spectrum
System (DSSS)
• A DSSS system can reduce the effects of interference on the
transmitted information.
• An interfering signal may be reduced by a factor which may be as high
as the processing gain.
• That is, a DSSS transmitter can withstand more interference if the
length of the PN sequence is increased.
• The output signal to noise ratio of a DSSS receiver may be expressed
as: (SNR)o = PG. (SNR)I, where (SNR)I is the signal to noise ratio
before the dispreading operation is carried out.
 Direct Sequence (DS) Spread Spectrum
System (DSSS)
• A major disadvantage of a DSSS system is the ‘Near-Far effect’,
illustrated in Fig.
 Direct Sequence (DS) Spread Spectrum
System (DSSS)
• This effect is prominent when an interfering transmitter is close to the
receiver than the intended transmitter.
• Although the cross-correlation between codes A and B is low, the
correlation between the received signal from the interfering
transmitter and code A can be higher than the correlation between
the received signal from the intended transmitter and code A.
• So, detection of proper data becomes difficult.
 Frequency Hopping Spread Spectrum
• Another basic spread spectrum technique is frequency hopping. In a
frequency hopping (FH) system, the frequency is constant in each
time chip; instead it changes from chip to chip. An example FH signal
is shown in Fig.7.38.3.
Frequency Hopping Spread Spectrum
 Frequency Hopping Spread Spectrum
• Frequency hopping systems can be divided into fast-hop or slow-hop.
• A fast-hop FH system is the kind in which hopping rate is greater than
the message bit rate and in the slow-hop system the hopping rate is
smaller than the message bit rate.
• This differentiation is due to the fact that there is a considerable
difference between these two FH types.
• The FH receiver is usually non-coherent.
• A typical non-coherent receiver architecture is represented in
Fig.7.38.4.
 Frequency Hopping Spread Spectrum
• The incoming signal is multiplied by the signal from the PN generator
identical to the one at the transmitter.
• Resulting signal from the mixer is a binary FSK, which is then
demodulated in a "regular" way.
• Error correction is then applied in order to recover the original signal.
• The timing synchronization is accomplished through the use of early-
late gates, which control the clock frequency
• https://www.youtube.com/watch?v=6qNWQxRKoss
 Time Hopping
• A typical time hopping signal is illustrated in the figure below. It is
divided into frames, which in turn are subdivided into M time slots. As
the message is transmitted only one time slot in the frame is
modulated with information (any modulation).
• This time slot is chosen using PN generator.
• All of the message bits gathered in the previous frame are then
transmitted in a burst during the time slot selected by the PN
generator.
• The transmitted signal bandwidth is 2M times the message
bandwidth.
 Time Hopping
• A typical time hopping receiver is shown in Fig.7.38.5. The PN code
generator drives an on-off switch in order to accomplish switching at
a given time in the frame.
• The output of this switch is then demodulated appropriately. Each
message burst is stored and re-timed to the original message rate in
order to recover the information.
• Time hopping is at times used in conjunction with other spread
spectrum modulations such as DS or FH. Table 7.38.1 presents a brief
comparison of major features of various SS schemes.
THANK YOU