Scribd
Upload
942 views

Function of Steering System

The steering system controls the direction of front wheels to steer the vehicle. It transmits road feedback and maintains the correct steering effort. Common types are linkage and rack-and-pinion systems. Linkage uses a gearbox to convert rotational motion to linear motion for the wheels. Rack-and-pinion uses a pinion gear that engages a rack for direct steering actuation. Power steering uses hydraulic assistance from an engine-driven pump. Diagnosing issues like play, effort, or noise can identify problems like low fluid, worn parts, or air in the system.

Uploaded by

Teju Love
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
942 views

Function of Steering System

The steering system controls the direction of front wheels to steer the vehicle. It transmits road feedback and maintains the correct steering effort. Common types are linkage and rack-and-pinion systems. Linkage uses a gearbox to convert rotational motion to linear motion for the wheels. Rack-and-pinion uses a pinion gear that engages a rack for direct steering actuation. Power steering uses hydraulic assistance from an engine-driven pump. Diagnosing issues like play, effort, or noise can identify problems like low fluid, worn parts, or air in the system.

Uploaded by

Teju Love
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
You are on page 1/ 19

Steering System

Function of Steering System

•Control of front wheel (sometimes


rear wheel) direction.

•Transmit road feel (slight steering


wheel pull caused by the road surface)
to the drivers hand.

•Maintain correct amount of effort


needed to turn the wheels.

•Absorb most of the shock going to the


steering wheel as the tire hits holes
and bumps in the road.

•Allow for suspension action.


Steering System
Turning the Car (when turning, front wheels don’t point the same direction)

•Inside wheel turns at a smaller radius, hence the inside wheel turns at a
steeper angle then the outside wheel.
Steering System
Linkage Steering System (Worm Gear)
Steering System
Linkage Steering System (Worm Gear) Parts

•Steering Wheel – used by the driver to rotate a


steering shaft that passes through the steering
column.

•Steering Shaft – transfers turning motion from


the steering wheel to the steering gearbox.

•Steering Column – supports the steering column


and steering shaft.
Steering System
Linkage Steering System (Worm Gear) Parts

•Steering Gearbox) – changes turning motion


into a straight-line motion to the left or right.

•Steering gear box ratios range from 15:1 to


24:1 (with 15:1, the worm gear turns 15 times
to turn the selector shaft once).

•Steering linkage – connects the steering


gearbox to the steering knuckles and wheels.
Steering System
Basic Rack-and-Pinion Steering
Steering System
Basic Rack-and-Pinion Steering

•Pinion Gear- rotated by the steering wheel and steering shaft; it’s teeth mesh
with the teeth on the rack.
•Rack- long steel bar with teeth along one section; slides sideways as the pinion
gear turns.
Steering System
Basic Rack-and-Pinion Steering

•Gear Housing- holds the pinion


gear and rack.

•Tie-rods- connects the rack with


steering knuckles.
Steering System
Basic Rack-and-Pinion Steering

•Part of rack contains a piston


•Two fluid ports, one on each side.
•The side with high pressure pushes the piston to the
opposite side (turning the wheel).
Steering Linkage

Pitman Arm transfers gearbox motion to the steering linkage.

•Pitman arm is splined to the gearbox.


Steering Linkage

Center Link (Relay Rod) steel bar connects the right and
left side of the steering linkage.

•Connects to Pitman arm, Tie rod ends, and Idler arm.


Steering Linkage

Idler Arm supports the end of the center link on


the passenger side of the vehicle.
•Bolts to the vehicle’s frame.
•If worn, will cause excessive steering play.
Steering Linkage

Tie-Rod Assemblies: Two tie-rod assemblies are used


to fasten the center link to steering knuckles.
•Assembly is consist of inner tie-rod end, outer tie-rod end,
and a toe adjustment sleeve.
•Be sure to check the toe setting after replacing the
tie-rod ends.
Steering Linkage

Rack-and-pinion outer tie-rod end is similar to


the regular tie-rod end, but the inner tie-rod end
sits inside the rack assembly.
Steering System
Power Steering normally use an engine driven pump and a hydraulic
system to assist steering action.

Three major types of power steering systems:

•Integral-piston linkage system.

•External power steering system.

•Rack-and-pinion system

•Integral power piston.


•External power piston.

Integral Rack-and-pinion system


is the most common.
Steering System
Power steering pump is driven by the engine produces the hydraulic
pressure for steering system operation.

Four basic pumps:

•Roller pump.

•Vane pump.

•Slipper pump.

•Gear pump.
Steering System Diagnosis
Steering Wheel Play is the most common problem.

Should not be able to turn the steering wheel


more than 1 ½’’ (33mm) without causing
movement of the front wheels.

Move the wheel side-to-side,


should have no play.
Steering System Diagnosis
Hard Steering (steering wheel requires excessive turning effort)

•Low power steering fluid.

•Pump belt broken or slipping.

Steering System Noise


•Belt squeal is a loud screeching sound produced by a worn belt.

•Power steering pump noise is usually a loud whine that only occurs when
the steering wheel is turned.
•Low fluid level and air in the system.

Check fluid with engine turned off.


Steering System
Credits:
Google search engine

You might also like