Introduction to Reliefs

Chapter 9
Introduction
• Despite many safety precautions within chemical plants,
equipment failures or operator errors can cause
increases in process pressures beyond safe levels.
• If pressures rise too high, they may exceed the
maximum strength of pipelines and vessels.
• This can result in rupturing of process equipment,
causing major releases of toxic or flammable chemicals.
• The defence against this type of accident is to prevent
the accident in the first place.
• Inherent safety, is the first line of defence.
• The second line of defence is better process control.
• A major effort is always directed toward controlling the
process within safe operating regions.
• Dangerous high-pressure excursions must be prevented
or minimized.
• The third line of defence against excessive pressures is
to install relief systems
• Relieve liquids or gases before excessive pressures are
developed.
• The relief system is composed of the relief device and
the associated downstream process equipment to safely
handle the material ejected.
The method used for the safe installation of
pressure relief devices
• The first step in the procedure is to specify where relief devices
must be installed.
Second, the appropriate relief device type must be selected
• The type depends mostly on the nature of the material relieved
and the relief characteristics required.
• Third, scenarios are developed that describe the various ways
in which a relief can occur.
• The motivation is to determine the material mass flow rate
through the relief and the physical state of the material
(liquid, vapor, or two phases).
• Next, data are collected on the relief process, including physical
properties of the ejected material, and the relief is sized.
• Finally, the worst-case scenario is selected and the final
relief design is achieved
Relief method

In this chapter we introduce relief

fundamentals and the steps in the
relief design procedure.
 Relief Concepts
• To protect personnel from the dangers of over
pressurizing equipment
• To minimize chemical losses during pressure
upsets
• To prevent damage to equipment
• To prevent damage to adjoining property
• To reduce insurance premiums
• To comply with governmental regulations
 Pressure versus time for runaway reactions
Assume that an exothermic reaction is occurring within a reactor.
If cooling is lost because of a loss of cooling water supply,
failure of a valve, or other scenario,
then the reactor temperature will rise.

• As the temperature rises,

• Reaction rate increases,
• Leading to an increase in heat
production.

(A) Relieving vapor,

(B) Relieving froth (two-phase flow)
(C) Closed reaction vessel
• Reaction runaways for large commercial reactors can occur in
minutes,
• Temperature and pressure increases of several hundred
degrees per minute
• Several hundred psi per minute, respectively
• If the reactor has no relief system, the pressure and
temperature continue to rise until the reactants are
completely consumed, as shown by curve C
• If the reactor has a relief device, the pressure response
depends on the relief device (curve A)
 Definitions that are commonly used
within the chemical industry
• Set pressure: The pressure at which the relief device
begins to activate

• Maximum allowable working pressure (MAWP):

• This is sometimes called the design pressure.
• Gauge pressure permissible at the top of a vessel for a
designated temperature
• Operating temperature increases, the MAWP decreases
• Operating temperature decreases, the MAWP decreases
• Vessel failure typically occurs at 4 or 5 times the MAWP
• Deformation may occur at as low as twice the MAWP
 Description of overpressure and
accumulation
• Operating pressure: The gauge pressure during normal
service, usually 10% below the MAWP
 Definitions

• Accumulation: The pressure increase over the MAWP

of a vessel during the relief process.
It is expressed as a percentage of the MAWP.
• Overpressure: The pressure increase in the vessel over
the set pressure during the
• Relieving process. Overpressure is equivalent to the
accumulation when the set pressure is at the MAWP. It is
expressed as a percentage of the set pressure.
• Backpressure: The pressure at the outlet of the relief
device during the relief process resulting from pressure
in the discharge system.
 Definitions

• Blowdown: The pressure difference between the relief

set pressure and the relief reseating pressure. It is
expressed as a percentage of the set pressure.
• Maximum allowable accumulated pressure: The sum
of the MAWP and the allowable accumulation.
• Relief system: The network of components around a
relief device, including the pipe to the relief, the relief
device, discharge pipelines, knockout drum, scrubber,
flare, or other types of equipment that assist in the safe
relief process.
 Guidelines for relief pressures. Adapted
from API RP 521,

Pressure-Relieving
and Depressuring
Systems
 Relief Types and Characteristics
Specific types of relief devices are chosen for specific
applications.
There are two general categories of relief devices
(spring-operated and rupture discs)
two major types of spring-operated valves
(conventional and balanced-bellows)
 On spring-operated valves the adjustable
spring tension offsets the inlet pressure
The relief set pressure is usually specified at 10% above
the normal operating pressure.

balanced-bellows
conventional spring-operated relief

• the valve opens based on • design the bellows on the

the pressure drop across backside of the valve seat
the valve seat; that is, the ensures that the pressure on
set pressure is proportional that side of the seat is always
to the pressure drop across atmospheric.
the seat. • Therefore the flow is reduced
as the backpressure increases
There are three subcategory types of spring-loaded pressure
reliefs:
• 1. The relief valve is primarily for liquid service. The relief
valve (liquid only) begins to open at the set pressure. This
valve reaches full capacity when the pressure reaches 25%
overpressure.
• 2. The safety valve is for gas service. Safety valves pop
open when the pressure exceeds the set pressure.
pressure, the valve reseats at approximately 4% below the
set pressure; the valve has a 4% blowdown.
• The safety relief valve is used for liquid and gas service.
 Major types of relief devices

Rupture discs are specially designed to rupture at a specified relief

set pressure. They usually consist of a calibrated sheet of metal
designed to rupture at a well-specified pressure
Buckling-Pin Reliefs
• A buckling-pin relief is similar to a rupture disc; that is,
when the pressure buckles the pin, the valve opens fully.
 Pilot-Operated Reliefs

The main valve of a pilot-operated relief valve is controlled

by a smaller pilot valve that is a spring-operated relief valve.
The pilot and main valves reseat when the inlet pressure drops
below the set pressure.
452
• Pilot-operated valves are frequently chosen when operating
pressures are within 5% of set pressures.
Chatter
• In general, relief systems must be designed appropriately to
prevent unwanted and dangerous problems.
• Included in this design are the sizing of the relief and also the
mechanical piping details
• Chattering is the rapid opening and closing of a relief valve that
can cause valve seat damage or the mechanical failure of the
internals.
• The major cause of valve chatter is an oversized relief valve.
• In this case the valve opens a short time to reduce the pressure
and the pressure then rises rapidly to open the valve again.
• This pulsating action can be very destructive.
• The major causes of chatter are excessive inlet pressure drop,
high backpressures, and oversized valves.
 Relief Scenarios
• A relief scenario is a description of one specific relief event.
• Usually each relief has more than one relief event.
• Largest relief vent area.
• Examples of relief events are
1. A pump is dead-headed; the pump relief is sized to handle the full pump
capacity at its rated pressure.
2. The same pump relief is in a line with a nitrogen regulator; the relief is
sized to
handle the nitrogen if the regulator fails.
3. The same pump is connected to a heat exchanger with live steam; the
relief is sized
• This is a list of scenarios for one specific relief.
• The worst-case scenarios are identified later by means of the
computed maximum relief area for each scenario and relief.
• Only three reliefs have multiple scenarios that require the
comparative calculations to establish the worst cases.
 Relief Installation Practices
• Regardless of how carefully the relief is sized, specified,
and tested, a poor installation can result in completely
unsatisfactory relief performance.
Some installation guidelines are illustrated
 Relief Design Considerations

• A designer of relief systems must be familiar with

governmental codes, industrial standards, and insurance
requirements.
• This is particularly important because local government
standards may vary.
• Codes of particular interest are published by the
American Society of Mechanical Engineers
American Petroleum Institute
National Board of Fire Underwriters
• API RP 5207 has some guidelines
• Reliefs are now rarely vented to the atmosphere.
• In most cases a relief is first discharged to a knockout
system to separate the liquid from the vapor.
 Relief Design Considerations

• Here the liquid is collected and the vapor is discharged

to another treatment unit.
• This subsequent vapor treatment unit depends on the
hazards of the vapor;
• it may include a condenser, scrubber, incinerator, flare,
or a combination of them.
• This type of system is called a total containment system.
• Total containment systems are commonly used, and they
are becoming an industrial standard.
 Relief containment system
with blowdown drum

Horizontal Knockout Drum Tangential inlet knockout drum

When space within a plant is limited, a tangential knockout

drum is used
 Flares
• The objective of a flare is to burn the combustible or
toxic gas to produce combustion products that are
neither toxic nor combustible.
• The diameter of the flare must be suitable to maintain a
stable flame and to prevent a blowout (when vapor
velocities are greater than 20% of the sonic velocity)
• The height of a flare is fixed on the basis of the heat
generated and the resulting potential damage to
equipment and humans.
• The usual design criterion is that the heat intensity at
the base of the stack is not to exceed 1500 Btu/hr/ft2.
• The effects of thermal radiation are shown in the following
table

Scrubbers
• If the vapors are toxic, a flare (described previously) or a
scrubber system may be required.
• Scrubber systems can be packed columns, plate columns, or
venturi-type systems.
 Condensers
• A simple condenser is another possible alternative for
treating exiting vapors.
• This alternative is particularly attractive if the vapors
have a relatively high boiling point and if the recovered
condensate is valuable.
• This alternative should always be evaluated because
it is simple and usually less expensive and because it
minimizes the volume of material that may need
additional post-treatment.