ACP Solution Step by

Step Training Slides

www.huawei.com

Copyright © 2012 Huawei Technologies Co., Ltd. All rights reserved.

Background and Benefits
 In dense urban or urban scenarios, such as complex network scenarios, how to balance coverage and interference
and other optimization objectives on RF optimization process , so that the best coverage and performance can
achieve.
 Compared to the traditional network Optimization method, ACP could improve the efficiency on the RF
optimization process, and reduce the cost on the manpower and its skill requirement.

HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential 2

ACP Introduction

HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential 3

Multi Target Optimization
 Multi targets optimization
Weak coverage area identification Result configuration and validation
Coverage
Based site B Coverage enhance site B
Parameter Weak coverage
Planning &
Optimization site A site A
site C site C

Quality Interference area identification Result configuration and validation

Based Interference Interference
detection site B site B
Parameter control
Planning &
Optimization site A
site A
site C site C

MR based high traffic cell identification Result configuration and validation

Load Based High traffic
High traffic area site B site B
Parameter area
Planning &
Optimization
site A site A
site C site C

HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential 4

 Analysis Steps

HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential 5

Step-1-Logging In to Genex Cloud
https://genexcloud-sahic.sd.huawei.com:8080/genexcloud/portal/login.do

User name &

password

HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential 6

Step-2
Once you logged in, Open the Network optimization Tab

Open Network
Optimization

HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential 7

Step-3
After Network optimization ,Open the ACP Tab

Open ACP

HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential 8

Step-4-Logging In to Genex Cloud
Open the new Task Tab

Open New
Task TAB

HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential 9

Step-5

Assign Task
Name and
Check the
UMTS,LTE-
FDD,LTE-TDD
Boxes,
Click next

Assign Task Name and Check the UMTS,LTE-FDD,LTE-TDD Boxes and Click NEXT

HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential 10

Step-6

Upload all
required
tabs data
and Draw
polygon

Load the all required data as shown below including DT data for each technology and the click next.
It will ask you to select DATA Check option select yes and then click next

HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential 11

Step-7

Open New
Task TAB

Select Virtual Layer Settings and add UMTS,FDD and TDD (if technologies have multiple carrier
frequencies) into Virtual setting and then click on advance settings on right top corner.

HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential 12

Step-8

Select the Antenna

port definition

Select Save

Select Antenna Port Definition and then select the appropriate Frequency band for that antenna port correspondence to technology.i.e
for UMTS select the port (2001-2200).Click Save

HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential 13

Step-9

Select
close
Select the Automatic
Combination and then
select the option
“By Physical
Antenna "Click Save

Select the Automatic Combination and then select the option “By Physical Antenna “ (We have been using same
antennae for all tech) click Save then close this TAB.

HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential 14

Step-10

Select Manual 1st and

click on Generate
Tuning cells

Select this option and

click Next

Select Manual 1st and click on Generate Tuning cells. It will generate two tuning files as shown below, Save these two
files into your system and define the ranges for E-Tilt, Mtilt( Min & Max)), and azimuth(min, max).Now upload these
two file again here.

HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential 15

Step-11 1st Select Coverage
first

Once its load all the data as

shown on left side, Delete
the one that has Overlapping
layers (It depends upon
carriers you have on each
Tech

2nd Select Overshooting

Coverage Optimization
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential 16
Step-12 Select Network Evaluation and new tab
will open's shown below select DT
Analysis and select RUN for all three
technologies.

HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential 17

Step-13 select Overshooting
Audit and new window
will pop up as shown
below.

select Each
Technology one
by one and
select Audit

HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential 18

Step-14
Select Highest Cell Gain and Click RUN. Now your task has been submitted
and it will be analyzed to give you recommendations.

Select Highest Cell

Gain and Click RUN
the task

HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential 19

ACP Solution Checklist
No. Progress/Steps Check Points Details
1 Verify emap that can cover your target optimization cluster
2 Update Cell load(TCP/PRB Utilization(decimal 0.0~1.0)) to matching with DT period, and it should greater than CIPICHPower （ w)/MaxPower(w) in engg. parameters
3 Check engg. Parameter intergrity, update EP with the latest CFG
4 Data Preparation Check whether Co-sector the same Lon/Lat/Azimuth/M-tilt/Height/Ant type, Co-Freq band and co-sector same E-tilt(same port)
5
Running the macro with exported DT data from assistant and check the process result, each value should in the corresponding column delete ARFCN+PSC/EARFCN+PCI blank
result to faster the calculating
6 Can draw the polygons after import EPT and DT data on the GIS, the optimization polygon should include all DT route, the buffer polygon should at least two more tiers sites
7 Click "Next" in Data Upload page to validate the data, check the validate result after it finish, should correct the errors and upload data again
Data Validate and Check
8 Click Data Check the check area should be the buffer polygon to check the result "Cells only in DT“ or missing sites in engg. parameters, or the cells is beyond the emap
9 Setting Virtual layer, rule: each RAT should take the participate freq into the virtual layer
10 Go to Advance setting on the right-up ， setting antenna port for each Ant based on the antenna freq ， and mapping each RAT to the corresponding port
11 Antenna Combination——By Physical Antenna (if same antennae being used for each tech)
12 Back to General, select the tuning parameter accordingly then click GenerateTuningCell
General setting download the Power configuration/ antenna configuration file, setting power tune(true/false) and range(3,-3) according the current load(TCP<=30% or TCP>=80%),and setting
13 the ranges for E-tilt, M-tilt(min, max), and azimuth(-30~30), for the cells which already know can not be adjusted(lampost/BB/Abseilling...) should be set the parameter tune to
false.
14 upload the power configuration/ antenna configuration file
15 tick the "LTE UE DT indicator" if the DT data is UE data, if it is scanner data, not tick it.
16 the Click the "Next" to "Optimization Objectives"
17 Click "Coverage first" and overshooting "Automatically Generate Threshold", to calculate the thresholds
Optimization Objectives Setting
18 select "Highest Cell gain" under "Implementation Strategy"
19 During the threshold calculating, can click "Network Evaluation", go to "DT Analysis" and "Overshooting Audit"
20 Network Evaluation (Optional) Click "DT Analysis", and click "GEO Analysis" for each participated RAT
21 Click "Overshooting Audit", set the target layer and tick the corresponding DT data then click "Audit", do the same for other layer.
22 Submit task Go back to "Optimization Objectives", then click "RUN" to submit the task.
23 Back to the task when you receive a process end email
24 Review the result Go to "Online Analysis", and export "Tuning Result" and "Cell Optimize Result"
25 Then vlookup all cell level improvements to the Tuning result, and review the result with the improvements, remark the remaining changes
26 Back to ACP Planning->General, go to Advance setting on the right-up ， set antenna combination with "None"
27 Back to General->RF Parameters, select "Manual", then click "GenerateTuninngCell"
Setting Prediction task with
reviewed solution Download the Power configuration/ antenna configuration file, and vlookup the remaining changes to the correponding cells and corresponding parameter in manual
28
column,then upload the configuration file, especially for E-tilt ， need fulfill Initial column for E-tilt for the changes cells as well.
29 Then submit the task
30 Prepare Report
Prepare the report by taking capture from "Online Analysis" after modify the legends. Can modify the Grid Width on the URL to the 1/25 of the zoom plotting scale, if the grid
can not see clear on the map.

HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential 20

 Thank you
www.huawei.com

Copyright©2011 Huawei Technologies Co., Ltd. All Rights Reserved.

The information in this document may contain predictive statements including, without limitation, statements
regarding the future financial and operating results, future product portfolio, new technology, etc. There are a number
of factors that could cause actual results and developments to differ materially from those expressed or implied in the
predictive statements. Therefore, such information is provided for reference purpose only and constitutes neither an
offer nor an acceptance. Huawei may change the information at any time without notice.