EEE4227: POWER SYSTEM

PROTECTION
TERM: MID-TERM
 Lecture 02
Part 01- High voltage circuit breaker
(HVCB)
Part 02- Low voltage circuit
breaker(LVCB)
 Part 01-High voltage circuit breaker (HVCB)

 What is a circuit breaker(CB)??

 A circuit breaker is an automatically operated electrical
switch designed to protect an electrical circuit from
damage caused by overload or short circuit.
 Depending on the voltage level CB can be classified into
two categories
 High voltage CB
 Low voltage CB
Working principle of a HV CB
(incorporated with relay):
When fault occurs in the
protective circuit, relay
connected to CT and PT actuate
and close its contacts. Current
flows from battery and closes the
trip circuit. As the trip coil is
energized, the circuit operating
mechanism is actuated, and it
operates for opening mechanism.
 Sequence of fault clearing process using CB

Fault occurs

Relay senses the fault and closes the trip

circuit Arc is extinguished at the instant when the
fault AC current is zero

Energizes the trip coil and unlatch the spring

Fault interruption is completed i.e. fault is
cleared

Contact starts to apart and arc is drawn

between the contact of CB
 Arc flash in CB
 What is arc flash??
 Arc flash in CB
 Available arc quenching methods: (i) High resistance interruption (ii) Low
•  resistance or zero point interruption:

 High resistance interruption:

 The resistance of arc is increased by lengthening and cooling it to such an
extent that the system can't maintain the arc and thus extinguishes

 Low resistance or zero point interruption:

 The arc gets extinguished at the natural current zero of the alternating
current wave
 Classification of CB (based on voltage
level and arc quenching method)

Miniature Circuit Air Blast Circuit

Breaker, Breaker, Air
break CB
Air break CB
 High voltage circuit breakers
 Air break circuit breaker (ACB)
 Air blast circuit breaker (ABCB)
 Oil circuit breaker
Minimum oil circuit breaker (MOCB)
Bulk oil circuit breaker (BOCB)
 SF6 circuit breaker
 Vacuum circuit breaker
Air break circuit breaker (ACB)
Air blast circuit breaker
Minimum oil circuit breaker
Bulk oil circuit breaker
SF6 circuit breaker
Vacuum circuit breaker
 Summary
HV CB Voltage level VA level

Air break CB up to 600 V 5-35 MVA

Vacuum CB 11 KV 500 MVA
Bulk Oil CB up to 12 KV 500 MVA
Minimum oil CB 33-245 KV 30000 MVA
Air blast CB 245-400 KV 35000 MVA

SF6 CB 245-700 KV 35000-50000 MVA

 Time and speed of circuit breaker
 CB time :  Speed of CB and Relay:
 Fault clearing time= [Relay time] + [Circuit  Before 1930: CB interrupting time: 15-30
breaker time] cycles; Relay interrupting time: 6-120
 Relay time= [Instant to fault] to [Closure of cycles
trip circuit]
 1930: CB interrupting time: 8 cycles
 Circuit breaker time= [Closure of trip
circuit] to [Final arc extinction] =[Opening  1935: CB interrupting time: 3 cycles
time + Arcing time]  Present days relay time becomes as small
 i.e. Fault clearing time= [Instant to fault] as 1-3 cycles
to [Arcing time]
 Review of short circuit fault
 Short circuit fault:
 Whenever a fault occurs on a network such that a large current flows in one or
more phases, a short-circuit is said to have occurred.
 Causes of short circuit fault:
 Internal effects: Aging of insulation ,inadequate design or improper installation
 External effect: Lighting surges, over loading of equipment causing excessive
heating, mechanical damage by public
 Effects of short circuit fault:
 Excessive heating due to heavy current that may damage equipment.
 Low voltage created by fault has a very harmful effect on the service rendered
by the power system.
 Review of short circuit fault
 Types of short circuit fault:
 Symmetrical fault
L-L-L fault
L-L-L-G fault
 Asymmetrical fault
Single L-G fault
L-L or double line fault
L-L-G or double line to ground fault
 Review of short circuit fault
 Transients in RL circuits: Symmetrical ac
component
Consider the following R-L circuit

Summation of ac
and dc component
 Review of short circuit fault
 Transients of short circuit fault current if the fault is at the terminal of a synchronous
generator
 Ratings of a CB

•  

Rated voltage: corresponds to the higher system voltage for which the circuit breaker is intended.
Rated current: r.m.s. value of the current which the circuit breaker can carry continuously.
 Rated short circuit breaking current: r.m.s value of the fault current under transient period.
 Rated symmetrical breaking current=
 Rated short circuit breaking capacity (Rupturing Capacity) of a CB= √3 X kV (Rated Voltage) X kA
(symmetrical breaking current)
 Rated short circuit making current: peak value of the fault current is called the making current of the CB.
 Rated short circuit making current= 1.8 X √2 X rated short circuit breaking current (symmetrical)
= 2.55 X rated short circuit breaking current (symmetrical)
 Making Capacity = 2.55 X symmetrical breaking capacity
 Rated duration of short circuit (rated short time current)(short time rating): r.m.s value of current that
the CB can carry in a fully closed position during a specified time under prescribed conditions of use and
behavior.
 Mathematical problem

• Problem
  1: A three phase CB is rated 1250 A, 2000 MVA (breaking
capacity), 33kV, 4 sec. Find the symmetrical breaking current, making
current and short time rating.
 Solution:
 Rated symmetrical rms breaking current ==34.99 kA
 Rated making current = 2.55 X 34.99kA = 89.23kA
 Short time rating = 34.99kA for 4 sec.
 Difference between CB and Fuse

  Fuse Circuit breaker

It performs both detection and It performs interruption function
Function only. The detection of fault is
interruption functions
made by relay system
Operatio Requires elaborate equipment
Inherently completely automatic (i.e. relays) for automatic action
n
Breaking
Small Very large
capacity
Operatin Comparatively large (0·1 to 0·2
Very small (0·002 sec or so) sec)
g time
Replacem Requires replacement after every
No replacement after operation
ent operation
End of part 01
 Part 02-Low voltage circuit breaker (LVCB)

 Low voltage circuit breaker can be of two categories-

Miniature circuit breaker (MCB)
Moulded case circuit breaker (MCCB)
 Features of LVCB
 In these circuit breakers arc extinction is carried under normal
air.
 Rating of MCB is up to 100A.
 Rating of MCCB is up to 100A to 1000A.
 there are 1 pole/2 pole/3 pole MCB for single phase or three
phase.
 But MCCB can only be 3 pole for 3 phase.
 In HVAC CB, there is a trip relay.
 In MCB and MCCB, there is trip release rather than trip relay.
 Difference between trip relay and trip
release

Trip relay Trip release

Used in high voltage system Used in low voltage system
A relay initiates the closure of the trip No separate relay is required to open
circuit for opening the contact of a CB the contact of MCB/MCCB under
under fault or abnormal operating abnormal operating condition. A
condition. bimetallic element for thermal overload
sensing and a magnetic coil for fault
current sensing are connected in series
with the circuit. This trip release is a
mechanism which directly helps to open
the contacts of MCB/MCCB
Components of a MCB
 Components of a MCB
Direction of current flow Internal construction of Internal construction of
during operation magnetic trip unit thermal trip unit
 Working principle of MCB
Thermal trip unit operation Magnetic trip unit operation
 Difference between MCCB/MCB and CB

MCB/MCCB CB
Used as switch under normal Used as switch under normal
operating conditions operating conditions

Tripping mechanism is Tripping mechanism is actuated

actuated by trip release by trip relay

Used in LV system Used in HV system

Low rupturing capacity High rupturing capacity
Coordination between CB and fuse

For faults on outgoing

feeders, Fuse2 of that feeder
should operate first.Fuse1
would provide backup. For
any fault on LT bus, Fuse1
should operate first and HV
circuit breaker should
provide backup.
Coordination between CB and fuse

It is the normal practice

not to use any CB on the
HT side of the distribution
transformer below
500kVA. In this case, fuses
are used on the both sides
of the transformer.
 Mathematical problem
 Suggest a guide line for the protection of HT and LT
side of a transformer rated as 250 KVA, 450 V/11KV
and Impedance 4.75%. The blow out time for the
corresponding fault current is given in the following
TCC curve. Also justify your answer on the selection
of protective components.
 Mathematical problem
•  
Solution:
Transformer rating= 250 kVA
Transformer voltage ratio= 0.415/11 kV
Zpu= 4.75%= 0.0475 pu

Now,
 Mathematical problem
•  

So, for LT side, fuse of 355 Amp should be chosen and for HT side fuse of 20 Amp should be
chosen.
End of part 02
• Reference-
• Chapter 19/ Principles of power systems/
V.K.Mehta & Rohit Mehta.
Prepared by
Susmita Ghosh
Assistant Professor
American International University-Bangladesh(AIUB)
Dept-EEE/Faculty of Engineering