Scribd
Upload
92 views

CRT Working

The document summarizes the key components and operation of a cathode ray tube (CRT) display. It describes how CRTs work by using an electron gun to produce a focused electron beam that is deflected to strike phosphors on the screen, causing them to glow. The screen image is refreshed rapidly as the beam scans back over the same points to maintain the picture. It then provides details on the electron gun, focusing and deflection systems, control electrodes, and screen phosphors used in CRTs.

Uploaded by

Comedy Mashup
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
92 views

CRT Working

The document summarizes the key components and operation of a cathode ray tube (CRT) display. It describes how CRTs work by using an electron gun to produce a focused electron beam that is deflected to strike phosphors on the screen, causing them to glow. The screen image is refreshed rapidly as the beam scans back over the same points to maintain the picture. It then provides details on the electron gun, focusing and deflection systems, control electrodes, and screen phosphors used in CRTs.

Uploaded by

Comedy Mashup
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
You are on page 1/ 7

CRT

CRT

A cathode ray tube (CRT) is a specialized vacuum tube in which images are produced
when an electron beam strikes a phosphorescent surface. Most desktop computer
displays make use of CRTs. The CRT in a computer display is similar to the "picture
tube" in a television receiver.

All CRT's have three main elements: an electron gun, a deflection system, and a screen.
The electron gun provides an electron beam, which is a highly concentrated stream of
electrons. The deflection system positions the electron beam on the screen, and the
screen displays a small spot of light at the point where the electron beam strikes it.

Refresh CRT

A beam of electrons (cathode rays), emitted by an electron gun, passes through focusing
and deflection systems that direct the beam towards specified position on the phosphor-
coated screen. The phosphor then emits a small spot of light at each position contacted
by the electron beam. Because the light emitted by the phosphor fades very rapidly, some
method is needed for maintaining the screen picture. One way to keep the phosphor
glowing is to redraw the picture repeatedly by quickly directing the electron beam back
over the same points. This type of display is called a refresh CRT.
Basic Operation of a CRT

The basic operation of CRT is shown in figure below:


Electron Gun

The primary components of an electron gun in a CRT are the heated metal cathode and
a control grid. The cathod is heated by an electric current passed through a coil of wire
called the filament. This causes electrons to be boiled off the hot cathode surface. In the
vacuum inside the CRT envelope, negatively charged electrons are then accelerated
toward the phosphor coating by a high positive voltage. The accelerating voltage can be
generated with a positively charged metal coating on the in side of the CRT envelope
near the phosphor screen, or an accelerating anode can be used. Sometimes the
electron gun is built to contain the accelerating anode and focusing system within the
same unit.

Focusing System

The focusing system is ised to create a clear picture by focusing the electrons into a
narrow beam. Otherwise, electrons would repel each other and beam would spread out
as it reaches the screen. Focusing is acomplished with either electric or magnetic fields.
Deflection System

Deflection of the electron beam can be controlled by either electric fields or magnetic
fields. In case of magnetic field, two pairs of coils are used, one for horizontal deflection
and other for vertical deflection. In case of electric field, two pairs of parallel plates are
used, one for horizontal deflection and second for vertical deflection as shown in figure
above.

Control Electrode

It is used to turn the electron beam on and off

CRT Screen

The inside of the large end of a CRT is coated with a fluorescent material that gives off
light when struck by electrons. When the electrons in the beam is collides with phosphor
coating screen, they stopped and their kinetic energy is absorbed by the phosphor. Then
a part of beam energy is converted into heat energy and the remainder part causes the
electrons in the phospor atom to move up to higher energy levels. After a short time the
excited electrons come back to their ground state. During this period, we see a glowing
spot that quickly fades after all excited electrons are returned to their ground state.
Persistence

It is defined as the time they continue to emit light after the CRT beam is removed.
Persistence is defined as the time it take the emitted light from the screen to decay to
one-tenth of its original intensity. Lower-persistence phosphors require higher refresh
rates to maintain a picture on the screen without flicker. A phosphor with low
persistence is useful for animation ; a high-persistence phosphor is useful for displaying
highly complex, static pictures. Although some phosphor have a persistence greater than
1 second, graphics monitor are usually constructed with a persistence in the range from
10 to 60 microseconds.

Resolution

The number of points per centimeter that can be used be plotted horizontlly and
vertically. Or Total number of points in each direction.

The resolution of a CRT is depend on type of phosphor

intensity to be displayed

focusing and deflection system


Aspect Ratio

It is ratio of horozontal to vertical points.

Example: An aspect ratio of 3/4 means that a verticle line plotted with three points has
same lenght as horizontal line plotted with four points.

You might also like