Chapter 2

Diode Applications
 Objectives

 Explain and analyze the operation of both half and

full wave rectifiers
 Explain and analyze filters and regulators and
their characteristics
 Explain and analyze the operation of diode limiting
and clamping circuits
 Explain and analyze the operation of diode voltage
multipliers
 Interpret and use a diode data sheet
 Troubleshoot simple diode circuits
 Introduction

The basic function of a DC power supply is to

convert an AC voltage to a smooth DC voltage.
 Half Wave Rectifier

A half wave rectifier

(ideal) allows
conduction for only
180° or half of a
complete cycle.

The output
frequency is the
same as the
input.
The average VDC or Vavg = Vp/
VAVG = Vp/
Average Value of Half-Wave Voltage

Vavg = Vp/p See Ex.2-1 pg.52

 Effect of the Barrier Potential

Vp(out) = Vp(in) – 0.7 Volts

Note:
Vin must overcome the barrier potential (0.7V) before
the diode becomes forward biased.
 Half Wave Rectifier – Barrier Potential

• Approx. 0.7V is “dropped” across the forward-biased diode junction.

• This voltage is removed at the broad base of the waveform.

Vp(in) – 0.7V. = Vp(out)

See Ex. 2-2 Pg.53 1207Chap2Fig2_5].ms8

 Half Wave Rectifier - Peak Inverse Voltage

Peak inverse
voltage is the
maximum voltage
across the diode
when it is in
reverse bias.
(blocking mode)

The diode must be

capable of
withstanding this
amount of voltage.
(-Vp(in)).
 Peak Inverse Voltage (PIV)

PIV

• Diode must be able to withstand PIV (Peak Inverse) voltage

 PIV calculations

PIV = ((Vpsec/2) – 0.7V) – (-Vpsec/2) =

((Vpsec/2) + (Vpsec/2)) – 0.7V =
Vpsec – 0.7V
Ex. 2-5 pg. 59 1207Chap2Ex2_5.ms8
 Transformer-Coupled Half-Wave Rectifier

Vsec = N Vpri
Vp(out) = Vp(sec) – 0.7V

• Transformers are often used for voltage change and isolation.

• The turns ratio determines the output voltage.
• Islolation between the primary and secondary windings.
prevents shock hazards in the secondary circuit
See Ex.2-3 pg.55
 Full-Wave Rectifiers
A full-wave rectifier allows current to flow during both the
positive and negative half cycles or the full 360º. Note that
the output frequency is twice the input frequency.
Most power supplies use full-wave rectifiers. Half-wave
rectifiers see lesser applications like lo-cost power supplies.

The average VDC or VAVG = 2Vp/.

 Full-Wave Rectifier
Center-Tapped

This method of rectification employs two diodes connected to a

center-tapped transformer.
The peak output is only half of the transformer’s peak
secondary voltage.

Center-tap
 Full-Wave Center Tapped
Note the current flow
direction during both
alternations. Being that it
is center tapped, the peak
output is about half of the
secondary windings total
voltage.

Each diode is subjected to a

PIV of the full secondary
winding output minus one
diode voltage drop.

PIV=2Vp(out) +0.7V
 Transformer Turns Ratio

Non-center-tapped transformer:
• For a turns ratio (output/input) = 1, Output Vp = Input Vp.
• For a turns ratio = 2, Output Vp = Input Vp/2

Center-tapped transformer:
• For a turns ratio (output/input) = 1, Output Vp = Input Vp/2.
• For a turns ratio = 2, Output Vp = Input Vp
 The Full-Wave Bridge Rectifier
The full-wave
bridge rectifier
takes advantage of
the full output of
the secondary
winding.

It employs four
diodes arranged
such that current
flows in the same
direction through
the load during
each half of the
cycle.
 The Full-Wave Bridge Rectifier

The PIV for a bridge rectifier is approximately half the PIV

for a center-tapped rectifier. PIV=Vp(out) +0.7V

Note: In most cases we take the diode drop into account.

Ex. 2-6 Pg.62 1207Chap2Ex2_6.ms8

 Power Supply Filters And Regulators
As we have seen, the output of a rectifier is a pulsating DC.
With filtration and regulation this pulsating voltage can be
smoothed out and kept to a steady value.
 Power Supply Filters And Regulators

A capacitor-input
filter will charge
and discharge
such that it fills in
the “gaps”
between each
peak. This
reduces variations
of voltage. The
remaining voltage
variation is called
ripple voltage.
 Power Supply Filters And Regulators
The advantage of a full-wave rectifier over a half-wave is quite clear.
The capacitor can more effectively reduce the ripple when the time
between peaks is shorter.

Ripple is
approx. ½
with full-wave
rectification.
 Ripple Voltage Calculations

Vr(pp) = (1/fRLC)Vprect

VDC = (1 – 1/2fRLC)Vp(rect)
Ripple Calc. cont’d.

Ex. 2-7 pg.66

 Power Supply Filters And Regulators

Being that the

capacitor appears
as a short during
the initial charging,
the current through
the diodes can
momentarily be
quite high. To
reduce risk of
damaging the
diodes, a surge
current limiting
resistor is placed in
series with the filter
and load.
 Power Supply Filters And Regulators
Regulation is the last step in eliminating the remaining ripple and
maintaining the output voltage to a specific value. Typically this
regulation is performed by an integrated circuit regulator. There are
many different types used based on the voltage and current
requirements.
 Power Supply Filters And Regulators

How well the regulation is performed by a regulator is

measured by it’s regulation percentage.

There are two types of regulation, line and load.

Line and load regulation percentage is simply a ratio of
change in voltage (line) or current (load) stated as a
percentage.
Line Regulation = (VOUT/VIN)100%

Load Regulation = (VNL – VFL)/VFL)100%

 Diode Limiters (Clippers)
Diode Limiters “clip” the positive portion (a) of the sinewave and
in (b), (diode reversed), clip the negative portion (less the diode
conduction voltage of 0.7V.)
 Diode Limiters (Clippers)

Biased “clippers” limit the positive or negative amount of an

input voltage to a specific adjustable value (VBIAS +0.7V).

This positive limiter will limit the output to VBIAS + .7V

 Diode Limiters
The desired amount of limitation can be attained by a power supply
or voltage divider. The amount clipped can be adjusted with different
levels of VBIAS.

This positive limiter will limit The voltage divider provides the VBIAS .
the output to VBIAS + .7V VBIAS =(R3/R2+R3)VSUPPLY

See Ex. 2-11 pg.74

 Diode Clampers (DC Restorers)
A diode clamper adds a DC level to an AC voltage. The capacitor charges
to the peak of the supply minus the diode drop. Once charged, the
capacitor acts like a battery in series with the input voltage. The AC
voltage will “ride” along with the DC voltage. The polarity arrangement of
the diode determines whether the DC voltage is negative or positive.

0V.
 Diode Clampers (DC Restorers)
Applications:
Amplifiers of all types use capacitive coupling between stages. Why?
To simplify the DC biasing; allows stage by stage independent biasing.
This capacitive coupling “loses” the DC component, stage to stage. To
“restore” DC, the Diode Clamper can be used.
Here is a –DC Restorer circuit
 Voltage Multipliers

Clamping action can be used to increase peak rectified voltage.

Once C1 and C2 charges to the peak voltage they act like two
batteries in series, effectively doubling the voltage output. The
current capacity for voltage multipliers is low.

Voltage Doubler
 Voltage Multipliers
The full-wave voltage doubler arrangement of diodes and
capacitors takes advantage of both positive and negative
peaks to charge the capacitors giving it more current
capacity. Voltage triplers and quadruplers utilize three and
four diode-capacitor arrangements respectively.
 Voltage Multipliers - Triplers
The voltage tripler arrangement adds another diode/capacitor
set. + half-cycle: C1 charges to Vp through D1,
- half-cycle: C2 charges to 2Vp through C2,
Next + half-cycle: C3 charges to 2Vp through C3.
Output is across C1 & C3.
 Voltage Multipliers - Quadruplers
The voltage tripler arrangement adds another diode/capacitor
set. + half-cycle: C1 charges to Vp through D1,
- half-cycle: C2 charges to 2Vp through C2,
Next + half-cycle: C3 charges to 2Vp through C3.
Next - half-cycle: C4 charges to 2Vp through C4
Quadruple Output is across C2 & C4.
 The Diode Data Sheet

The data sheet for diodes and other devices gives

detailed information about specific characteristics.
• maximum current
• voltage ratings,
• temperature range, and
• voltage versus current curves.
It is sometimes a very valuable piece of information,
even for a technician. There are cases when you might
have to select a replacement diode when the type of
diode needed may no longer be available.
 The Diode Data Sheet

Acrobat Document Acrobat Document

1N914 1N4001
 Troubleshooting

Our study of these devices and how they work

leads more effective troubleshooting. Efficient
troubleshooting requires us to take logical
steps in sequence. Knowing how a device,
circuit, or system works when operating
properly must be known before any attempts
are made to troubleshoot. The symptoms
shown by a defective device often point
directly to the point of failure. There are many
different methods for troubleshooting. We will
discuss a few.
 Troubleshooting

Here are some helpful troubleshooting techniques:

 Power Check: Sometimes the obvious eludes the

most proficient troubleshooters. Check for fuses
blown, power cords plugged in, and correct battery
placement.
 Sensory Check: What you see or smell may lead
you directly to the failure or to a symptom of a
failure.
 Component Replacement: Educated guesswork in
replacing components is sometimes effective.
 Troubleshooting

Signal tracing is the most popular and most accurate. We

look at signals or voltages through a complete circuit or
system to identify the point of failure. This method requires
more thorough knowledge of the circuit and what things
should look like at the different points throughout.
 Troubleshooting

This is just one example of troubleshooting that illustrates

the effect of an open diode in this half-wave rectifier circuit.
Imagine what the effect would be if the diode were shorted.
 Troubleshooting

This gives us an
idea of what
would be seen in
the case of an
open diode in a
full-wave rectifier.
Note the ripple
frequency is now
half of what it was
normally. Imagine
the effects of a
shorted diode.
 Summary

 The basic function of a power supply is to give us a

smooth ripple free DC voltage from an AC voltage.
 Half-wave rectifiers only utilize half of the cycle to
produce a DC voltage.
 Transformer Coupling allows voltage manipulation
through its windings ratio.
 Full-Wave rectifiers efficiently make use of the
whole cycle. This makes it easier to filter.
 The full-wave bridge rectifier allows use of the full
secondary winding output whereas the center-tapped
full wave uses only half.
 Summary

 Filtering and Regulating the output of a rectifier helps

keep the DC voltage smooth and accurate.
 Limiters are used to set the output peak(s) to a given
value.
 Clampers are used to add a DC voltage to an AC
voltage.
 Voltage Multipliers allow a doubling, tripling, or
quadrupling of rectified DC voltage for low current
applications.
 Summary

 The Data Sheet gives us useful information and

characteristics of device for use in replacement or
designing circuits.
 Troubleshooting requires use of common sense along with
proper troubleshooting techniques to effectively determine the
point of failure in a defective circuit or system.