TEST 35

1. What is the lightest known metal?

A. Mercury
B. Steel
C. Chromium
D. Aluminum
2. Material having high electrical resistance and
should not be used as conductor.

A. Magnesium
B. Copper
C. Nickel
D. Iron
3. The property that characterizes a materials ability
to be drawn into a wire is known as

A. Plasticity
B. Elasticity
C. Ductility
D. Utility
4. Stress relieving is also _____ for the purpose of
reducing internal stress of steel material/metal.

A. Quenching
B. Normalizing
C. Tempering
D. Drawing
5. A carbon content in the range of ____ in steel
readily responds to heat treatment.

A. 0.35 to 0.40% C
B. 0.28 to 0.30% C
C. 0.18 to 0.25% C
D. 0.12 to 0.15% C
6. It indicates how many times a volume of material is
heavier than an equal volume of water.

A. Specific gravity
B. Specific volume
C. Specific weight
D. Specific density
7. Nickel – chromium – molybdenum steel designation
SAE ______.

A. 81xx
B. 74xx
C. 94xx
D. 64xx
8. Moment of inertia is also called

A. Modulus of elasticity
B. Weep strength
C. Radius of gyration
D. None of the above
9. It is hardening treatment whereby a cast metal is
being heated to a very high temperature then
suddenly subject to rapid cooling to improve
hardenability of wear resistance is called

A. Annealing
B. Normalizing
C. Tempering
D. Quenching
10. A good general purpose deoxidizer which
promotes fined grain in steel

A. Copper
B. Magnesium
C. Molybdenum
D. Silicon
11. Treatment process that produces a residual
compressive stress at the surface and residual tension
on the inside that results in considerable increase in
fatigue strength for members on torsion/bending is
known

A. Partial quenching
B. Heavy oil quenching
C. Quenching
D. Shallow quenching
12. The flux that should be provided in soldering
electrical connection or commutator wires as it tends
to corrode the connections.

A. Sal ammoniac
B. Zinc chloride
C. Stearin
D. Acid fluxes
13. The characteristics of tool steel sustain shocks and
major impacts is due to its

A. Toughness
B. Stiffness
C. Ductility
D. Machinability
14. The application of electrical current to the
corrosion circuit to counter the corrosion reaction is
called

A. Cathodic protection
B. Sacrificial anodes method
C. Chemical corrosion process
D. Galvanic action
15. A major component of cast steel is

A. Silicon
B. Iron
C. Manganese
D. Chromium
16. Normally, cast iron contains 2% carbon or more
and silicon in the range of ____%

A. 1 to 3
B. 1 to 4
C. 2 to 3
D. 1 to 6
17. The material for engine radiation is usually made
of _____.

A. Yellow brass
B. Silicon brass
C. Admiralty brass
D. Navy brass
18. A problem by-product used as an electrode in an
electric arc furnace melting operation is called

A. Anthracite coke
B. Foundry coke
C. Graphite electrodes
D. Bituminous coke
19. Which of the following does not effect the tensile
strength of steel?

A. Sulfur
B. Cobalt
C. Phosphorous
D. Boron
20. Alloy steel axle under repeated load/stress will
eventually fail if the load/stress is above the
endurance for the steel under consideration. The
endurance limit of the steel is

A. Equal to the allowable stress of the module of

elasticity
B. Equal to half of the ultimate strength
C. Equal to module of elasticity
D. Equal to 80% of the elastic limit
21. Mirror finish has surfaces of ____rms.

A. 1
B. 2 to 8
C. 1 to 3
D. 2 to 5
22. Chromium steel to include heat and corrosion
resistant designation

A. SAE 56xx
B. SAE 511xx
C. SAE 61xx
D. SAE 9xx
23. Non – metallic material of high melting
temperature being used as furnace lining.

A. Quartz bricks
B. Refractories
C. Silica sand
D. Dolomile clay bricks
24. In greater quantity, this element is harmful to the
molten ferrous metal.

A. Silica
B. Aluminum
C. Oxides
D. Sulfur
25. Silicon manganese steel designation, SAE___.

A. 72xx
B. 40xx
C. 92xx
D. 9xx
26. Cold drawing is also called _____.

A. Hard drawn
B. Oxidized steel
C. Cold lap steel
D. Strain hardening
27. The brittleness in steel at elevated temperature is
known as

A. Hard drawn
B. Cold lap
C. Red shortness
D. Residual stresses
28. Material may be stretched and still returns to its
former form/condition upon release of force is called

A. Plasticity
B. Modulus of elasticity
C. Ductility
D. Elastic limit
29. What is SAE specification number of molybdenum
chromium nickel?

A. 48xx
B. 47xx
C. 46xx
D. 45xx
30. Galvanized iron is term referring to iron coated
with _____.

A. Aluminum
B. Tin
C. Zinc
D. Manganese
31. A metal, which has high electrical conductivity but
should not be used for high temperature.

A. Silicon
B. Zinc
C. Chrome alloy
D. Carbide
32. It improves red hardness of steel.

A. Chromium
B. Cobalt
C. Boron
D. Lead
33. What is the SAE specification number of
molybdenum?

A. SAE 2xxx
B. SAE 3xxx
C. SAE 4xxx
D. SAE 5xxx
34. Which does not belong to the group?

A. SAE
B. AISI
C. SEA
D. ASTM
35. It is the ability of the material to resist
deformation under stress.

A. Plasticity
B. Stiffness
C. Toughness
D. All of the above
36. Which of the following is not a structural class of
steel?

A. High speed steel

B. Tool and die
C. Low carbon
D. High carbon
37. Continuous stretching under load even if the stress
is less than the yields point is known as

A. Plasticity
B. Elasticity
C. Creep
D. Ductility
38. Killed steel is always associated with

A. Silicon
B. Manganese
C. Phosphorous
D. Sulfur
39. The good deoxidizer in steel melting

A. Manganese
B. Silicon
C. Aluminum
D. All of the above
40. Good stabilizer in stainless steel is

A. Columbium
B. Titanium
C. Tantalum
D. All of the above
41. Metals are conductive because

A. The electrons are loosely bound to the nuclei and

therefore mobile
B. Having characteristics luster
C. They are on the left side of the periodic table
D. They have extra electrons as exhibited by normally
possible balance state
42. The yield strength of a rectangular yellow brass 65
to 70% Cu, 30 to 35% Zn can be increase/improve by
______.

A. Cold working
B. Tempering
C. Shill casting
D. Heat treatment
43. Used as cast condition steel casting with carbon
content less than ____ % C.

A. 0.26
B. 0.15 to 0.18
C. 0.20
D. 0.25
44. Liners are normally made of

A. Cast iron
B. Alloyed bronze
C. Alloyed steel
D. Alloyed aluminum
45. A furnace used in melting of non – ferrous metals
is called

A. Cupola furnace
B. Crucible furnace
C. Induction furnace
D. Normalizing furnace
46. A furnace used in melting ferrous metalss

A. Annealing furnace
B. Tempering furnace
C. Induction furnace
D. Normalizing furnace
47. All are associated with standard material specified
except

A. American Iron and Steel Institute

B. Society of Automotive Engineers
C. Southeast Asia Iron and Steel Institute
D. American Society for Testing Material
48. The ability of the material to be deformed
considerably without rupture is called

A. Malleability
B. Elasticity
C. Ductility
D. Plasticity
49. Permanent deformation or strain may occur
without fracture is called

A. Malleability
B. Elasticity
C. Ductility
D. Plasticity
50. An alloy that improves strength of steel at high
temperature application.

A. Tungsten
B. Molybdenum
C. Chromium
D. All of the above