Scribd
Upload
117 views

Water Level Indicator Persentation

The document describes a water level indicator using an Arduino and water sensor. It has 3 LEDs (red, yellow, green) to indicate different water levels in a tank. The red LED indicates a low level, yellow a medium level, and green LED with a buzzer will signal when the tank is full. The system uses a water level sensor that detects conductivity changes as the water level rises to determine the level. It has a simple, low-cost design that can help control water levels and prevent waste.

Uploaded by

akshay warghade
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
117 views

Water Level Indicator Persentation

The document describes a water level indicator using an Arduino and water sensor. It has 3 LEDs (red, yellow, green) to indicate different water levels in a tank. The red LED indicates a low level, yellow a medium level, and green LED with a buzzer will signal when the tank is full. The system uses a water level sensor that detects conductivity changes as the water level rises to determine the level. It has a simple, low-cost design that can help control water levels and prevent waste.

Uploaded by

akshay warghade
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
You are on page 1/ 13

WATER

LEVEL
INDICATOR

BY: PA36 VIJAY KUMAR


: PA44 AKSAY WARGHADE
: PA49 SAMARJIT
DAWKHAR
INTRODUCTION
• Water is the most essential element to life on earth.
• However safe drinking water is essential to humans and other life forms even though it provides
no calories or organic nutrients.
• , Some observers have estimated that by 2025 more than half of the world population will be
facing water-based vulnerability.
• The presence of a water level detector in a reservoir can help control wastage and water
inadequacy in such reservoir.
• . Aim & objectives of the study • to construct an electronic device that can automatically detect
water level (high and low) with high precision. • To control the supply of water
WATER
LEVEL We will be building a water level indicator using
arduino & water sensor.
INDICATOR
The system would indicate the level of the water
(three different levels) inside a tank with the help of
3 led and a buzzer to indicate that the tank is full.

This is a beginner level project and has a purposeful


implementation as well in our home.
Arduino Uno Breadboard 3 LED Buzzer (x1)
COMPONENTS (red,green,yellow)
REQUIRED

Jumper wires Water level sensor 220 ohms resistor


(x3)
DESIGN

• Step 1: Assemble LED on breadboard. We use LED of 3


different colors red, yellow, green. RED led indicating
extremely low level of water. YELLOW led indicating
half water level. Similarly, GREEN led indicating full
water level. Connect the cathode of each led to power rail
on breadboard which would be the ground supply.
Connect the anode of led's to different nodes and connect
220 ohms resistor in series with each LED.
DESIGN

STEP 2 STEP 3
• Make connections with arduino • Connect the water sensor with
and led. Red led connect with arduino.
digital pin of arduino and
similarly yellow and green led
connect with digital pin 12 and
digital pin 11 respectively.

STEP 4
• Connect the buzzer to digital pin
8 of arduino.
CIRCUIT DIAGRAM
WORKING PRINCIPLE

• When water tank is empty or there is very less water in the tank, RED led will start glowing. When water
falls into the tank and the water level starts increasing at that time, RED led stops glowing. Similarly, when
the water level in the tank reaches half level, YELLOW led starts glowing.

• When water level in the tank reaches up to full level, GREEN led starts blinking and buzzer starts buzzing.
This indicates that the water tank is full and the motor connected to water tank should be turned OFF.

• Water level sensor gives value into proportional to the water level resistive strip. Means increase in water
level conductivity increases the strip, Thus resistance decreases.

• Water level sensor values At low tank = 100-200


Mid tank = up to 450
And full tank = 600
MARKET SURVEY
COMPONENT QUANTITY COST( IN RS )

1. ARDUINO 1 400

2. 50GM METAL - 80/-

3. 9V BATTERY 1 20/-

4. BREAD BOARD 1 90/-

5. USB TO PRINTER 1 55/-

6. 12V BUZZER 1 30/-

7. 5MM LED 3 15/-

8. 220OHM RESISTER 3 5/-

9. 15W SOLDER 1 90/-


ADVANTAGES OF
WATER LEVEL
INDICATOR

Power saver

Money saver

Automatic

Water maximization

Reliable electronic design


Easy installation with LED
Monitoring
APPLICATION
•Home •Commercial
•Hotels •Factories
apartments complexes

•Residential and •Anywhere water •In vehicles as a


•Where cooling
commercial levels need to be fuel level
towers are used
swimming pools controlled indicator

•In huge
containers as a •Single phase •Single phase •Three phase
liquid level motor submersibles motors
indicator

•Used to start
•Open wells •Bore wells •Sump Pumps and stop water
pumps
CONCLUSION

• The water level Inndicator employs a simple mechanism to detect and indicate the water level in
an over head tank or any other water container. The sensing is done by using a set of three or four
probes which are placed at four different levels. We can conclude that this system is very
beneficial in rural as well as urban areas. It helps in the efficient utilization of available water
sources.
• If used on a large scale, it can provide a major contribution in the conservation of water for us and
the future generations. In these days, when the Earth's reserve of consumable water is decreasing
every moment, every drop has its value. Water level controller is a simple yet effective way to
prevent wastage of water. Its simplicity in design and low cost components make it an ideal piece
of technology for the common man.

You might also like