MATERIALS SCIENCE

Part of & AALearner’s Guide

Learner’s Guide
ENGINEERING
AN INTRODUCTORY E-BOOK
Anandh Subramaniam & Kantesh Balani
Materials Science and Engineering (MSE)
Indian Institute of Technology, Kanpur- 208016
Email: [email protected], URL: home.iitk.ac.in/~anandh
http://home.iitk.ac.in/~anandh/E-book.htm
Why are K1 and K2 peaks resolved at high angles?
&
Which ‘Line’ to use for lattice parameter calculation?

 At higher Bragg angles the K1 and K2 lines are resolved (reason shown in the next slide)
 Typically we use only the K1 lines for the calculation of lattice parameter
 The error in the calculation of lattice parameter decreases with increasing angle
→ hence the high angle peaks should be used for lattice parameter calculation
(instead of taking an average over all peaks or taking any of the intense low
angle peaks)
(as shown in slides to follow)
Why are K1 and K2 peaks resolved at high angles?
 The K1 (CuKα1 = 1.540598 Å) and K2 (CuKα2 = 1.54439 Å) lines differ slightly in
wavelength. Hence, in principle two separate peaks should be seen in the diffraction
pattern.
 Usually, at low angles these peaks are merged (i.e. seen as a single peak) and at high angles
these peaks are resolved (seen as two separate peaks). The question is why?
 This can be understood in terms of the variation of  with  (as in this case  is not fixed)
and the graphical (Ewald sphere) construction (upcoming slides).
200

K1 & K2 peaks resolved in high angle peaks

(in 222 and 400 peaks this can be seen)
220
111

311
222

400
In low angle peaks K1 & K2 peaks merged
 8

(1/Cos(q )
5

0
0 10 20 30 40 50 60 70 80 90
q

n   2 d Sin d
 2 d Cos
d
d 1

d  2 d Cos
 1 and 2 differ slightly in wavelength
• The difference in the diffracted angle 
increases with an increasing angle of
diffraction  (for a given ). Plot of
variation as above.
• Hence, the 1 and 2 peaks are resolved at
high angles
Actually, the variation in 2 is to be seen
Which ‘Line’ to use for lattice parameter calculation?
 Typically we use only the K1 lines for the calculation of lattice parameter. And this can be
done at high angles as the K1 & K2 lines are resolved at high angles.
 The error in the calculation of lattice parameter decreases with increasing angle → hence
the high angle peaks should be used for lattice parameter calculation (instead of taking an
average over all peaks or taking any of the intense low angle peaks) (as shown in slides to follow).
Let us calculate the error in d spacing as a function of the angle of diffraction
1


d
2 Sin 0.9

0.8

0.7

0.6

0.5
Sin(t)

0.4 t
Fo
r the 0.3

sa
me
 0.2

the
err
or
in 0.1

Si
n

wi 0
th 0 30 60 90


 14
d (d )  Cos
 12 d (d ) Cos  d
d 2 Sin 2  d   Cot d
d Sin Tan
d (d )  Cos  d 10
 d 
d Sin Tan 
8

Cot(t)
Error in d spacing 6

2
t
0
0 20 40 60 80 100

Error in d spacing decreases with 

→ hence high angle peaks have to be used for lattice parameter calculation
 Determination of Lattice parameter from 2 versus Intensity Data

n 2  Sin Sin2  ratio Index a (nm)

1 38.52 19.26 0.33 0.11 3 111 0.40448
2 44.76 22.38 0.38 0.14 4 200 0.40457

Decreasing error
3 65.14 32.57 0.54 0.29 8 220 0.40471
4 78.26 39.13 0.63 0.40 11 311 0.40480
5* 82.47 41.235 0.66 0.43 12 222 0.40480
6* 99.11 49.555 0.76 0.58 16 400 0.40485
7* 112.03 56.015 0.83 0.69 19 331 0.40491
8* 116.60 58.3 0.85 0.72 20 420 0.40491
9* 137.47 68.735 0.93 0.87 24 422 0.40494

*  1 , 2 peaks are resolved (1 peaks are listed) Others methods exist for precise
lattice parameter measurement (than
a just taking a single value)!
1.54  2 d 422 Sin 422  2 0.93
24 o
aCalculated from the 422 line  4.0494 A