Heat

Exchangers

Nov 7, 2023
Heat Exchangers Function

1-H. Ex. Function is to transfer heat energy from a fluid to

another fluid

2-Double action can be applied in the same time,

a- Cooling a fluid is required as a terminal product.
b- Heating another fluid is required as a heat recovery.

Heat Transfer modes

Conduction
Convection
Radiation

07/11/2023

Nov 7, 202
 Heat transfer methods
• Conduction; Heat energy is transferred through solid objects
such as tubes, heads, baffles, plates, fins, and shell, by
conduction. This process occurs when the molecules that make
up the solid matrix begin to absorb heat energy from a hotter
source. Since the molecules are in a fixed matrix and cannot
move, they begin to vibrate and, in so doing, transfer the energy
from the hot side to the cooler side.
Conduction is the fastest and most efficient way of transferring
heat between two solid objects.
• Convection: is heat transfer by mass motion of a fluid such as
air or water when the heated fluid is caused to move away from
the source of heat, carrying energy with it. Convection above a
hot surface occurs because hot air expands, becomes less dense,
and rises.
• Radiation: Radiation is a method of heat transfer that does not
rely upon any contact between the heat source and the heated
object as is the case with conduction and convection. Heat can
be transmitted through empty space by thermal radiation often
called infrared radiation. This is a type electromagnetic
radiation . No mass is exchanged and no medium is required in
the process of radiation. Examples of radiation is the heat from
the sun
 Types of Heat Exchangers
Heat Exchangers can be classified according to the direction of
flowing of the two fluids to each other.
• Co-current (parallel) flow: Exists when both the tube side fluid
and the shell side fluid flow in the same direction. In this case,
the two fluids enter the heat exchanger from the same end with a
large temperature difference. As the fluids transfer heat, hotter to
cooler, the temperatures of the two fluids approach each other.
Note that the hottest cold-fluid temperature is always less than
the coldest hot-fluid temperature.
• Counter current flow: Exists when the two fluids flow in
opposite directions. Each of the fluids enters the heat exchanger at
opposite ends. Because the cooler fluid exits the counter flow heat
exchanger at the end where the hot fluid enters the heat exchanger,
the cooler fluid will approach the inlet temperature of the hot
fluid.
Counter flow heat exchangers are the most efficient of the
three types.
• Cross flow: exists when one fluid flows perpendicular to the
second fluid; that is, one fluid flows through tubes and the
second fluid passes around the tubes at 90° angle. Cross flow
heat exchangers are usually found in applications where one of
the fluids changes state (2-phase flow).
Factors Affect Heat Transfer in Heat Exchangers
Tubes metal
Mass flow Rate
Temperature difference
Fouling
Time of Exposure
Flow regime

Type of Flow
Laminar Flow
Laminar Flow is usually exist at low flow rate

Turbulent Flow
Turbulent Flow is usually exist at high flow rate, allows molecules to mix
and absorb heat more readily than does laminar flow.
Turbulent Flow decrease thickness of static film, increasing
the rate of heat transfer.
Can be classified also according to service .

 Heat Exchanger
Both sides single phase and process stream

 Cooler
One stream process fluid and the other cooling water or air

 Heater
One stream process fluid and heating utility as steam

 Condenser
One stream condensing vapor and the other cooling water or air

 Reboiler
One stream bottom stream from a distillation column and the other a hot utility.

10
 Classifications; according to Geometry

Heat Exchangers

Double Shell and Plate and Air

Pipe coil Hairpin Reboilers Plate Fins Spiral
Pipe Tube Frame Cooled
Classifications
Heat Exchangers

Pipe coil Double Pipe Hairpin Shell and Tube Reboilers Plate and Frame Plate Fins Air Cooled Spiral
Classifications
Heat Exchangers

Pipe coil Double Pipe Hairpin Shell and Tube Reboilers Plate and Frame Plate Fins Air Cooled Spiral
• A double-pipe exchanger has a pipe inside a pipe, The outside
pipe provides the shell, and the inner pipe provides the tube.

• The double pipe heat exchanger does not provide large heat
transfer surface areas and is commonly used for low heat duties
with smaller surface area requirements. When larger heat
exchange duty is required a number of these units can
connected in series or in parallel to fit into the space available.

• The double pipe heat exchanger is compact and the

components and fittings are small in dimension, which makes
them a natural choice for high-pressure services.

• Fins can be added to the internal tube’s external wall to

increase heat transfer.
Classifications
Heat Exchangers

Pipe coil Double Pipe Hairpin Shell and Tube Reboilers Plate and Frame Plate Fins Air Cooled Spiral
• The hairpin (Multi-pipe) resembles a typical shell-and-tube heat
exchanger, stretched and bent into a hairpin.
• excellent capacity for thermal expansion because of
its U-tube type shape.
• its finned design, which works well with fluids that have a low
heat transfer coefficient.
• its high pressure on the tube side.
• it is easy to install and clean; its modular design makes it easy
to add new sections.
Classifications
Heat Exchangers

Pipe coil Double Pipe Hairpin Shell and Tube Reboilers Plate and Frame Plate Fins Air Cooled Spiral
• The most common type of heat exchanger in industrial
applications.
• They contain a large number of tubes (sometimes several
hundred) packed in a shell with their axes parallel to that of the
shell. Heat transfer takes place as one fluid flows inside the tubes
while the other fluid flows outside the tubes through the shell.
• ideal for large scale applications.
• Shell-and-tube heat exchangers are further classified according
to the number of shell and tube passes involved.
Classifications
Heat Exchangers

Pipe coil Double Pipe Hairpin Shell and Tube Reboilers Plate and Frame Plate Fins Air Cooled Spiral
• A heating fluid like steam or hot oil flows through the tubes, the
shell side fluid is a liquid which partially vaporizes.

Kettle Type Reboiler

A large vapor cavity above the heated process medium allows
vapors to concentrate. Liquid that does not vaporize flows over a
weir and into the liquid outlet.

Thermosyphon Reboiler
is designed with no vapor space above the tubes, hence liquid and
vapor returned back to tower.
The critical design factor is providing sufficient liquid head in the
column to support vapor or liquid flow-back to the column.
Nov 7, 2023
Classifications
Heat Exchangers

Pipe coil Double Pipe Hairpin Shell and Tube Reboilers Plate and Frame Plate Fins Air Cooled Spiral
• Plate heat exchangers (PHE) have a number of pressed metal
plates, aligned on a frame clamped together with gaskets
between the plates.
• Each pressed plate is corrugated, having a alternating ridges and
grooves.
• The fluids flow between alternating plates. The flow distribution
depends upon the opening of the circumferential gasket (gasket
running around the outside of the plates) to an inlet or outlet
port. Circumferential gaskets surround the inlet and outlet ports.
These gaskets prevent mixing of the exchanger fluids.
• The corrugated plates create turbulence, which also promotes
high heat transfer rates, by continuously altering the flow
direction and velocity of the fluids.

Plate frame heat exchanger

• Easy to Remove and Clean
Plate Heat Exchangers are easy to clean by remove the tie bolts and
slide back the movable frame part. Then the plate pack can be
inspected, pressure cleaned, or removed for refurbishment if required.
• Expandable
A very significant feature of the plate Heat Exchanger is that it is
expandable. Increasing the Heat Transfer requirements means simply
adding plates instead of buying a new Heat Exchanger, saving time
and money.
• High Efficiency
Because of the pressed patterns in the plates and the relative narrow
gaps, very high turbulence is achieved at relative low fluid velocity.
This combined with counter directional flow results in very high
Heat Transfer coefficients.
Classifications
Heat Exchangers

Pipe coil Double Pipe Hairpin Shell and Tube Reboilers Plate and Frame Plate Fins Air Cooled Spiral
Classifications
Heat Exchangers

Pipe coil Double Pipe Hairpin Shell and Tube Reboilers Plate and Frame Plate Fins Air Cooled Spiral
• Air is used as the outside medium to transfer heat away from
the tubes.
• Fans can be mounted above or below the tubes in forced-draft
or induced-draft arrangements.
• Air-cooled heat exchangers can be found in service on air
compressors, in recirculation systems, and in condensing
operations.
• The aerial cooler is preferred for processes where the
temperature of fluids to be cooled is at least 55°C. They are also
used where fouling of the tubes on the cooling waterside of a
water-cooled exchanger is a concern. If a fluid stream at a high
temperature requires cooling below the ambient temperature, a
combination of aerial cooling followed by water-cooling will
often prove to be efficient and economical since a large portion
of the heat load is removed before the water is used.
2- FORCED-DRAFT

FAN

COLD
COLD AIR
AIR PASS
PASS THROUGH
THROUGH THE
THE
FAN
FAN

Nov 7, 2023
Auto variable Louvers
Louvers Automatic
Controlling gear

FAN

Nov 7, 2023
Classifications
Heat Exchangers

Pipe coil Double Pipe Hairpin Shell and Tube Reboilers Plate and Frame Plate Fins Air Cooled Spiral
• The hot fluid enters near the center of the exchanger and flows
from the inside outward. The cold fluid enters at the outside
and flows in the opposite direction toward the center. In this
way, true counter-flow is achieved.
• The continually curving passage creates high turbulence.
• The scrubbing effect of the fluids in each path minimizes
fouling significantly compared to tube style heat exchangers,
so spiral exchanger an excellent choice for fluids that tend to
deposit sludge or contain solids in suspension.
Heat Exchangers are classified according to their function:

Recuperative:
two fluids separated by a solid wall (this is the most common type)

Evaporative:
Enthalpy of evaporation of one fluid is used to heat or cool the
other fluid (condensers/evaporators and boilers)

Regenerative:
use a third material which stores/releases heat
Shell and Tube Heat Exchanger
 Main Components

1- Channel Cover 8- Shell

2- Channel 9- Baffles
3- Channel Flange 10- Floating Head backing Device
4- Pass Partition 11- Floating Tubesheet
5- Stationary Tubesheet 12- Floating Head
6- Shell Flange 13- Floating Head Flange
7- Tube 14 –Shell Cover
35
 Heat
Heat Exchanger
ExchangerConstruction
Construction

1-Floating
1-FloatingHead
HeadHeat
HeatExchanger
Exchanger
CHANNEL
HEAD BONNET
COVER OUT

VENT
TEMA AES TYPE Hx

CHANNEL
HEAD

TUBE SHELL
SHEET DRAIN
IN
TUBE TUBE
HEAD CHANNEL
BUNDLE
COVER HEAD BAFFLE
PLATES
FLOATIN VENT
G HEAD

One tubesheet is bolted onto the flange of the

exchanger while the other end is free to move
(float) as the exchanger heats up or cools down.

TUBE DRAIN
SHELL
SHEET
Nov 7, 2023
One tubesheet is bolted onto the flange of the exchanger while the
other end is free to move (float) as the exchanger heats up or cools
down.
2-
2- “U”
“U” Tube
Tube Heat
Heat Exchanger
Exchanger

OUT

TEMA AEU TYPE Hx VENT

DRAIN
Nov 7, 2023 IN
 VENT

it eliminates the problems of differential thermal expansion.

DRAIN

Nov 7, 2023
it eliminates the problems of differential thermal expansion.

The tubesheet is bolted onto one flange at one end of the

exchanger, but the tubes are free to expand and contract as
necessary inside the shell.

The U-tube bundle can be easily removed for cleaning and

maintenance.
3-Fixed
3-Fixed Tubes
Tubes Heat
Heat Exchanger
Exchanger

Tube Bundle is completely welded

OUT

TEMA NEN TYPE Hx

DRAIN
Nov 7, 2023 IN
 VENT VENT

DRAIN DRAIN

Nov 7, 2023
The fixed tubesheet shell and tube heat exchanger is simple in
design: and easy to fabricate, resulting in a lower initial capital
cost. Individual tubes can be easily repaired or plugged.

The main disadvantage is that the tube bundle cannot be

removed for cleaning, maintenance or inspection. Because of
this, the fixed tubesheet exchanger is best suited for service
where the shell side fluids are clean The inside of the tubes can
be accessed for cleaning and should be the side carrying the
dirtier fluid. Chemical cleaning is the only method of cleaning
the outside of the tubes.
TEMA; Tubular Exchanger Manufacturers Association

45
Front Head Type

A - Type B - Type C - Type

46
 Shell Type

E - Type F - Type

J - Type
K - Type 47
 Rear End Head Types

M - Type S - Type T - Type

Fixed Tubesheet Floating Head Pull-Through
Floating Head

48
 Baffle plates

Baffles are transverse or longitudinal plates installed on the shell

side of heat exchangers to force the shell side fluid to flow across
the tubes in a specific pattern, and to support and secure
the tubes and prevent vibration.
The modified flow improves heat transfer between the shell side
and tube side fluids.
 Longitudinal Baffles
• divide tube bundle and
shell Into two parts.
This done to achieve
multi-pass shell.
 IMPINGEMENT BAFFLE PLATES

Impingement Baffle are plates positioned under the inlet nozzle

of the shell to improve fluid Distribution.
protect tubing from direct fluid impact, preventing cutting, pitting,
and erosion problems in the tubes.
.
Impingement Baffle are used with gases and vapors Condensers.
 Tube lay out Patterns

Tube holes cannot be

drilled very close together,
since this may structurally
weaken the tube sheet. The
shortest distance between
two adjacent tube holes is
called the “clearance.”
Tubes are laid out in either
square or triangular
patterns.
Tube side passes
Two Pass Tube Bundle H.Ex. And One Pass Shell H.Ex.

One Pass Shell

Two Pass Tube
H.Ex.
Bundle H.Ex.
Four Pass Tube Bundle H.Ex. And Two Pass Shell H.Ex.

Two Pass Shell

Four Pass Tube
H.Ex.
Bundle H.Ex.
 One Pass
Shell H.Ex.
VENT

DRAIN

Nov 7, 2023
 Two Pass
Shell H.Ex.

Nov 7, 2023
Changing in Temp. Changing in Phase
Ex. Car Radiator Ex. Reboiler
 A Methodology for Heat Exchanger Design Calculations
- The Log Mean Temperature Difference (LMTD) Method -
A form of Newton’s Law of Cooling may be applied to heat exchangers by
using a log-mean value of the temperature difference between the two fluids:
 T1   T2
q  U A  T1m  T1m 
1n   T1 /  T2 
Evaluation of T1 and  T2 depends on the heat exchanger type.

• Counter-Flow Heat Exchanger:

 T1  Th ,1  Tc ,1
 Th , i  Tc , o

 T2  Th ,2  Tc ,2
 Th , o  Tc , i
• Parallel-Flow Heat Exchanger:

 T1  Th ,1  Tc ,1
 Th ,i  Tc ,i

 T2  Th ,2  Tc ,2
 Th , o  Tc , o

 Note that Tc,o can not exceed Th,o for a PF HX.

 For equivalent values of UA and inlet temperatures,
 T1m,CF   T1m, PF
 Heat Transfer in H. E.

Heat transfer in a heat exchanger is by conduction and convection.

The rate of heat transfer, "Q", in a heat exchanger
is calculated using the following equation:

Q = Uo Ao ∆ TLm

Q = Heat transfer rate (BTU/hr)

Uo = Overall heat transfer coefficient (BTU/hr-ft2-oF
Ao = Cross sectional heat transfer area (ft2)
∆ Tlm = Log mean temperature difference (o F)
Example
A heat exchanger is operated under the following conditions as
a counter flow and a co-current flow:
T1 =represents the hot fluid temperature
T1 in = 200 oF T1 out = 145 oF
Uo = 70 BTU/hr-ft2-oF Ao =75 ft2
T2 = represents the cold fluid temperature
T2 in = 80 oF T2 out = 120 oF
Solution
 Q = U o A o ∆ T lm
Heat Transfer for the counter flow conditions:
Q = (70 BTU ) (75 ft2 ) (72 o F)
hr - ft2 -o F
Q = 3.8 * 10 5 BTU / hr

Heat Transfer for the co-current flow conditions:

Q = (70 BTU ) (75 ft2 ) (61 o F)
hr - ft2 -o F
Q = 3.2 * 10 5 BTU / hr

The results demonstrate that given the same operating conditions,

operating the same heat exchanger in a counter flow manner will
result in a greater heat transfer rate than operating in parallel flow.
 Fluid Placement
• A. Shell-Side
1. Fluid having the lowest flow rate
2. Condensing or boiling fluid

• B. Tube-Side
1. Toxic fluids to minimize leakage
2. Corrosive fluids; (special alloy tubes can be used to resist
internal corrosion, which is much less expensive than building
the entire shell and tubes from special alloys).
3. Fouling fluids; since it is easier to clean, especially when
mechanical cleaning is needed.
4. High temperature fluids requiring alloy materials
5. High pressure fluid normally flows through the tubes since
tubes can collapse from overpressure forces from the outside.
 Start Up And Shutdown
On initial start up and shutdown the heat exchanger can be subjected to damage
Such as thermal chock, over pressure or hydraulic hammer
This can lead to leaky tube to tube sheet joints because of excessive thermal
expansion of tubes or the shell.
New H.Ex. Start Up Procedure
1. Check H.Ex. Parts no loose bolts,
2. All valves in the shut position.
3. Start cold fluid, then gradually start hot fluid.
4. When fluid stream is liquid, check that there is no
pocket gas via vent valve.
5. Check H.Ex Leaks
6. Temperature changes should be slowly, and flow rate
gradually increased

H.Ex. Shutdown Procedure

Stop the hot fluid first
H.Ex. Valves should not be closed while it is full of liquids.
How to detect Operational Problem
Decline of heat transfer efficiency
High pressure drop
Internal gasket leaks
Internal Tubes leaks
External leaks
Laboratory Sample results
Types Of H.Ex. Failure

1- Tubes Leaking
2- Tube Sheet Leaking
3- Tubes Plugging
4- Shell Plugging

H.Ex. Leak Test

Visual Leak Test
Hydrostatic Test
Sample Lab. Test
External Fouling

Nov 7, 2023
Tubes Plugging

Nov 7, 2023
Tubes Fouling

Nov 7, 2023
Heat Ex. Fouling

Fouling definition
Fouling is a trim used to describe undesirable deposits on a heat
exchanger surface. These deposits result in an increase of resistance
to both fluid flow and heat transfer. A slight sludge or scale buildup
on either side of the tube greatly reduces effectiveness. An increase
in pressure drop through the exchanger or a drop in heat exchange
efficiency usually indicates that cleaning is needed.

Types of Fouling

Mineral scales,
ƒ Sedimentation (dirt or clay in the cooling water supply),
ƒ Coking (hot surfaces and carbon deposits),
ƒ Corrosion

Nov 7, 2023
How to handle the problem of Fouling

• Mineral scales can be combated with chemical treatments while

the process is running.
• Sedimentation is prevented or lessened through the proper use of
a filtering system.
• Corrosion is prevented through the proper selection of exchanger
materials as well as through use of corrosion inhibitor.
• Coking is common in hydrocarbon processing and is not always
possible to eliminate.
• Hydro blasting cleaning (high pressure water jet pump) 10,000
psi
For out side tube fouling and Shell cleaning
Turbine cleaning for inside tube heavy fouling and Shell cleaning
 Hydrostatic Test
Hydrostatic test will supervised and responsibility of
Inspection department

Test blinds (capable to withstand the test pressure),

to be installed at inlet and outlet nozzles of shell and tube sides.

Apply pressure in shell side, check tubes leaking (outside or inside)

Drain the tube water

Apply pressure in tube side, check tubes leaking, tube sheet leaking
 HYDRAULIC
HYDRAULICTESTING
TESTING

Shell Side Test

Testing fluid

leaking
Tube

leaking
Tube Sheet

Nov 7, 2023
Tube Side Test
Testing fluid
U Tube

leaking
leaking Tubes
Tube Sheet
Tube Side Test
Testing fluid
Floating Head

leaking Floating Head

Nov 7, 2023
Tube Sheet Leaking
 Heat
Heat Exchanger
Exchanger Maintenance
Maintenance

MAXIMUM PLUGGED TUBES 20% TO 25% OF PASS TUBES NO.

VENT

DRAIN

Nov 7, 2023