Scribd
Upload
162 views

EEE 357 Circuit Analysis II Lecture 01 Contd.

This document discusses power in AC circuits. It defines instantaneous, active, and reactive power. Instantaneous power is the product of instantaneous voltage and current. Active power is the average power dissipated as heat and is proportional to the voltage, current, and cosine of the phase difference. Reactive power oscillates between electrical components and does not produce heat. Power factor is defined as the cosine of the phase difference and relates active power to apparent power. Power factor correction with capacitors is used to improve efficiency by reducing reactive power. Wattmeters are used to measure power by accounting for both voltage and current magnitudes and their phase difference.

Uploaded by

Shuvodip Das
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
162 views

EEE 357 Circuit Analysis II Lecture 01 Contd.

This document discusses power in AC circuits. It defines instantaneous, active, and reactive power. Instantaneous power is the product of instantaneous voltage and current. Active power is the average power dissipated as heat and is proportional to the voltage, current, and cosine of the phase difference. Reactive power oscillates between electrical components and does not produce heat. Power factor is defined as the cosine of the phase difference and relates active power to apparent power. Power factor correction with capacitors is used to improve efficiency by reducing reactive power. Wattmeters are used to measure power by accounting for both voltage and current magnitudes and their phase difference.

Uploaded by

Shuvodip Das
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
You are on page 1/ 21

Power In AC Circuit

Lecture 01 (Continued)

Course Conducted by Shuvodip Das, Lecturer, Dept. of ETE Prime University, Dhaka.

Power in AC Circuits
Introduction Power in Resistive Components Power in Capacitors Power in Inductors Circuits with Resistance and Reactance Active and Reactive Power Power Factor Correction Power Transfer Three-Phase Systems Power Measurement

Introduction
The instantaneous power dissipated in a component is a product of the instantaneous voltage and the instantaneous current p = vi In a resistive circuit the voltage and current are in phase calculation of p is straightforward In reactive circuits, there will normally be some phase shift between v and i, and calculating the power becomes more complicated

Power in Resistive Components


Suppose a voltage v = Vp sin t is applied across a resistance R. The resultant current i will be v VP sin t i IP sin t
R R

The result power p will be

The average value of (1 - cos 2t) is 1, so

1 cos 2t p vi VP sin t IP sin t VP IP (sin2 t ) VP IP ( ) 2

1 VP IP Average Power P VP IP VI 2 2 2

where V and I are the r.m.s. voltage and current

Relationship between v, i and p in a resistor

Power in Capacitors
From our discussion of capacitors we know that the current leads the voltage by 90. Therefore, if a voltage v = Vp sin t is applied across a capacitance C, the current will be given by i = Ip cos t Then p vi
VP sin t IP cos t VP IP (sint cos t ) sin 2t VP IP ( ) 2

Relationship between v, i and p in a capacitor

Power in Inductors
From our discussion of inductors we know that the current lags the voltage by 90. Therefore, if a voltage v = Vp sin t is applied across an inductance L, the current will be given by i = -Ip cos t Therefore p vi
VP sin t IP cos t VP IP (sint cos t ) sin 2t VP IP ( ) 2

Relationship between v, i and p in an inductor

Circuit with Resistance and Reactance


When a sinusoidal voltage v = Vp sin t is applied across a circuit with resistance and reactance, the current will be of the general form i = Ip sin (t - ) Therefore, the instantaneous power, p is given by
p vi VP sin t IP sin(t ) 1 VP IP {cos cos(2t )} 2 1 1 p VP IP cos VP IP cos(2t ) 2 2

1 1 VP IP cos VP IP cos(2t ) 2 2

The expression for p has two components The second part oscillates at 2 and has an average value of zero over a complete cycle
this is the power that is stored in the reactive elements and then returned to the circuit within each cycle

The first part represents the power dissipated in resistive components. Average power dissipation is
1 VP IP P VP IP (cos ) (cos ) VI cos 2 2 2

The average power dissipation given by


1 P VP IP (cos ) VI cos 2

is termed the active power in the circuit and is measured in watts (W) The product of the r.m.s. voltage and current VI is termed the apparent power, S. To avoid confusion this is given the units of volt amperes (VA)

From the above discussion it is clear that


P VI cos S cos

In other words, the active power is the apparent power times the cosine of the phase angle. This cosine is referred to as the power factor
Active power (in watts) Power factor Apparent power (in volt amperes)
Power factor P cos S

Active and Reactive Power


When a circuit has resistive and reactive parts, the resultant power has 2 parts:
The first is dissipated in the resistive element. This is the active power, P The second is stored and returned by the reactive element. This is the reactive power, Q , which has units of volt amperes reactive or var

While reactive power is not dissipated it does have an effect on the system
for example, it increases the current that must be supplied and increases losses with cables

Consider an RL circuit
the relationship between the various forms of power can be illustrated using a power triangle
Apparent Power

Reactive Power

Active power

Therefore

Active Power
Reactive Power Apparent Power

P = VI cos
Q = VI sin S = VI

watts
var VA

S 2 = P 2 + Q2

Power Factor Correction


Power factor is particularly important in high-power applications Inductive loads have a lagging power factor Capacitive loads have a leading power factor Many high-power devices are inductive
a typical AC motor has a power factor of 0.9 lagging the total load on the national grid is 0.8-0.9 lagging this leads to major efficiencies power companies therefore penalise industrial users who introduce a poor power factor

The problem of poor power factor is tackled by adding additional components to bring the power factor back closer to unity
a capacitor of an appropriate size in parallel with a lagging load can cancel out the inductive element this is power factor correction a capacitor can also be used in series but this is less common (since this alters the load voltage)

Power Measurement
When using AC, power is determined not only by the r.m.s. values of the voltage and current, but also by the phase angle (which determines the power factor)
consequently, you cannot determine the power from independent measurements of current and voltage

In single-phase systems power is normally measured using an electrodynamic wattmeter


measures power directly using a single meter which effectively multiplies instantaneous current and voltage

In three-phase systems we need to sum the power taken from the various phases
in three-wire arrangements we can deduce the total power from measurements using 2 wattmeter in a four-wire system it may be necessary to use 3 wattmeter in balanced systems (systems that take equal power from each phase) a single wattmeter can be used, its reading being multiplied by 3 to get the total power

Key Points
In resistive circuits the average power is equal to VI, where V and I are r.m.s. values In a capacitor the current leads the voltage by 90 and the average power is zero In an inductor the current lags the voltage by 90 and the average power is zero In circuits with both resistive and reactive elements, the average power is VI cos The term cos is called the power factor Power factor correction is important in high-power systems High-power systems often use three-phase arrangements

You might also like