Scribd
Upload
60 views

Load Frequency Control

Uploaded by

Mohit Jambu
Copyright
© © All Rights Reserved
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
60 views

Load Frequency Control

Uploaded by

Mohit Jambu
Copyright
© © All Rights Reserved
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
You are on page 1/ 13

Contents

⚫ Introduction

⚫ Reasons for constant frequency

⚫ Various modelings used in LPC


Generator model
Load model
Prime mover model
Governor model

⚫ Automatic Generation Control (AGC)

⚫ AGC of Single Area System

⚫ AGC of Two Area System


Introduction
⚫ In an electric power system, Load Frequency Control (LFC) is a
system to maintain reasonably uniform frequency, to divide the
load between the generators, and to control the tie- line
interchange schedules.

⚫ The change in frequency is sensed when the rotor angle ∂ is


changed.

⚫ The error signals are transformed into real power command signal,
which is sent to prime mover to call for an increment in the torque.

⚫ The prime mover then brings change in the generator


output by an amount which will change the values of within the
specified tolerance.
Reasons for constant frequency
⚫ The speed of the alternating current motors depends on the
frequency of the power supply. There are situations where speed
consistency is expected to be of high order.

⚫ The accuracy of the electric clocks are dependent on the frequency


of the supply.

⚫ If the normal frequency is 50 Hertz and the system frequency falls


below 47.5 Hertz or goes up above 52.5 Hertz then the blades of
the turbine are likely to get damaged so as to prevent the stalling of
the generator .

⚫ Due to the subnormal frequency operation the blast of the ID


and FD fans in the power stations get reduced and thereby
Various Modelings used in LFC
⚫ Generator Model:

Load Model:
⚫ Prime mover Model:

Fig: Block Diagram for a simple steam turbine


Governor Model:
Fig: Load Frequency control block diagram of an isolated power
system
Automatic Generation Control
⚫ Sometimes, load on the system is increased suddenly then the turbine speed
drops before the governor can adjust the input of the steam to the new load.

⚫ As the change in the value of speed diminishes, the error signal becomes smaller
and the position of the governor get closer to the point required to maintain the
constant speed.

⚫ One way to restore the speed or frequency to its nominal value is to add an
integrator on the way.

⚫ As the load of the system changes continuously the generation is adjusted


automatically to restore the frequency to the nominal value. This scheme is
known as automatic generation control.

⚫ In an interconnected system consisting of several pools, the role of the AGC is to


divide the load among the system, stations and generators so as to achieve
maximum economy and reasonably uniform frequency.
AGC of Single Area System
⚫ With the primary Load Frequency Control (LFC) loop a change in the system
load will result in a steady state frequency deviation , depending on the
governor speed regulation.

⚫ In order to reduce the frequency deviation to zero an integral


controller is connected to provide reset action on the load reference setting
to change the speed set point.

⚫ The integral controller gain must be adjusted for a satisfactory transient


response.

Fig: Mathematical Modeling of AGC for an isolated power system


AGC of a Multi- Area System
⚫ Now a days in most of the cases, a group of generators are
closely coupled internally and swing in unison.

⚫ These generator turbines tend to have the same response


characteristics and such a group of generators are said to be
coherent.

⚫ The LFC loop represent the whole system and the group is called
the control group.
Fig: Two Area system with primary loop LFC
References
⚫ www.ethesis.nitrkl.ac.in

⚫ www.en.openei.org

⚫ www.jatit.org
Thank You

You might also like