Sheet Metal Forming

EMU 1
 SHEET METAL WORKING
1. Cutting Operations
2. Bending Operations
3. Drawing
4. Other Sheet Metal Forming Operations

EMU
 Sheet Metalworking Defined
Cutting and forming operations performed on relatively
thin sheets of metal
 Thickness of sheet metal = 0.4 mm (1/64in) to 6mm
(1/4 in)
 Thickness of plate stock > 6 mm
 Operations usually performed as cold working

EMU
Sheet and Plate Metal Products
 Sheet and plate metal parts for consumer and
industrial products such as
 Automobiles and trucks
 Airplanes
 Railway cars and locomotives
 Farm and construction equipment
 Small and large appliances
 Office furniture
 Computers and office equipment

EMU
Advantages of Sheet Metal Parts
 High strength
 Good dimensional accuracy
 Good surface finish
 Relatively low cost
 Economical mass production for large
quantities

EMU
 Sheet Metalworking Terminology
 Punch‑and‑die - tooling to perform cutting,
bending, and drawing
 Stamping press - machine tool that performs
most sheet metal operations
 Stampings - sheet metal products made by
press machine

EMU
Basic Types of Sheet Metal Processes
1. Cutting
 Shearing to separate large sheets
 Blanking to cut part perimeters out of
sheet metal
 Punching/ Piercing to make holes in sheet
metal
2. Bending
 Straining sheet around a straight axis
3. Drawing
 Forming of sheet into convex or concave
shapes
EMU
Shearing, Blanking, and Punching
Three principal operations in press working that
cut sheet metal:
 Shearing
 Blanking
 Punching
 Piercing

EMU
 Sheet Metal Cutting - Shearing

Shearing of sheet metal between two cutting edges: (1) just before
the punch contacts work;
(2) punch begins to push into work, causing plastic deformation;

EMU
 Sheet Metal Cutting - Shearing

Shearing of sheet metal between two cutting edges: (3) punch

compresses and penetrates into work causing a smooth cut surface;
(4) fracture is initiated at the opposing cutting edges which separates
the sheet.

EMU
 Shearing
Sheet metal cutting operation along a straight line
between two cutting edges
 Typically used to cut large sheets

Engagement of entire blade

into cutting need higher
forces. Therefore, inclined
blade is used to reduce force
and to improve cut- edge.

Shearing operation: (a) side view of the shearing operation;

(b) front view of power shears equipped with inclined
upper cutting blade.
EMU
 Shearing
 Shearing is a process for cutting sheet metal to size
out of a larger stock such as roll stock.

 Shears are used as the preliminary step in preparing

stock for stamping processes, or smaller blanks for
CNC presses

 The shearing process produces a shear edge burr,

which can be minimized to less than 10% of the
material thickness.
 The burr is a function of clearance between the punch
and the die, and the sharpness of the punch and the
die. EMU
 Blanking and Punching
Blanking - sheet metal cutting to separate piece
(called a blank) from surrounding stock
Punching - similar to blanking except cut piece is
scrap, called a slug

(a) Blanking and (b) punching.

EMU
 Punching
 Punching is a metal fabricating process that
removes a scrap slug from the metal workpiece
each time a punch enters the punching die. This
process leaves a hole in the metal workpiece

EMU
 Punching: operation
 1. Punch, made of hardened steel, is forced through a work-piece.
 2. The punch cuts the metal and separates it in the form of scrap
3. The hole size depends on the punch size
Characteristics:
 Ability to produce economical holes in both strip and sheet metal during
medium or high production processes.
 The ability to produce holes of varying shapes - quickly

Punching is an operation
of cutting holes into a
sheet blank

EMU
 Punch Tools
TiN coated tool steel punches

To reduce punch wear

To increase punch life
To increase dimensional accuracy of holes
EMU
 Punch and Die Sizes

Die size determines blank

size Db;
Punch size determines
hole size Dh.;
c = clearance

EMU
Clearance in Sheet Metal Cutting
Distance between punch cutting edge and die
cutting edge
 Typical values range between 6% and 15% of
stock thickness
 If clearance is too small, fracture lines pass
each other, causing double buffing and
larger force
 If too large, metal is pinched and bent
between cutting edges and excessive burr
results

EMU
Clearance in Sheet Metal Cutting
 Recommended clearance is calculated by:
c = at
where c = clearance; a = allowance; and t =
stock thickness
 Allowance a is determined according to type of
metal
• Low “c” for soft materials
 High “c” for hard materials
 Typical “a” values for metals range from 0.04 to
0.09

EMU
 Punch and Die Sizes
 Blanking (Blank diameter is controlled)
- For a round blank of diameter, Db
 Diameter of die = blank diameter ( Db)
 Diameter of punch = Db - 2c
where c = clearance
 Punching (Hole diameter is controlled)
- For a round hole of diameter , Dh
 Diameter of punch = hole diameter (Dh )
 Diameter of die = Dh + 2c
where c = clearance
EMU
 Angular Clearance
Purpose: allows slug or blank to drop through die
 Typical values: 0.25 to 1.5 on each side

EMU
 Cutting Forces
Important for determining press size (tonnage)
F=StL
where S = shear strength of the metal; t = stock
thickness,
L = length of cut edge (contact length) = 2*3.14* R
L is basically perimeter of blank or hole being cut

The above formula is based on fact that entire

punch face is engaged in cutting.
If angled punched is used, cutting force will
reduce.

EMU
Example Problem

C= At

In blanking. Die size = blank size

Punch size =
die size - 2C

EMU
Example

F=StL

EMU
 Sheet Metal Bending
Straining sheet metal about a straight axis to
take a permanent bend

Bending of sheet metal

EMU
 Sheet Metal Bending
Metal below the neutral axis is compressed, while metal
above the neutral axis is stretched
Metal on neutral axis neither stretched nor compressed

•The material is stressed beyond the

yield strength but below the ultimate
tensile strength.
•The surface area of the material does
not change much., why??
•Bending usually refers to deformation
about one axis

EMU
 Types of Sheet Metal Bending
 V‑bending - performed with a V‑shaped die
 Edge bending - performed with a wiping die

EMU
 V-Bending
 For low production
 Performed on a brake press
 V-dies are simple and inexpensive

EMU
 Edge Bending

 For high production

 Pressure pad required
 Dies are more complicated and costly

EMU
 Stretching during Bending

 If bend radius is small relative to stock

thickness, metal tends to stretch during
bending
 Important to estimate amount of
stretching, so that final part length can be
obtained as specified dimension

EMU
 Springback
Increase in included angle of bent part relative to
included angle of forming tool after tool is
removed
 Reason for spring-back:
 When bending pressure is removed, elastic
energy remains in bent part, causing it to
recover partially toward its original shape

EMU
 Spring back (SB)

SB= (α’-α’b)/α’b

 

Springback in bending is seen as an increase in bend angle and bend

radius: (1) during bending, the work is forced to take radius Rb and
included angle b' of the bending tool, (2) after punch is removed, the
work springs back to radius R and angle ‘.
EMU
 Bending Force
Maximum bending force estimated as follows:

K bf TSwt 2
F
D

where F = bending force; TS = tensile

strength of sheet metal; w = part width in
direction of bend axis; and t = stock
thickness.
For V- bending, Kbf = 1.33; for edge bending,
Kbf = 0.33; D is opening width of a V-die or
wiping die
EMU
 Die Opening Dimension

Die opening dimension D: (a) V‑die, (b) wiping die.

EMU
 Example 20.2
-
 Example 20.2
- for v type die

EMU
 Drawing
Sheet metal forming to make cup‑shaped,
box‑shaped, or other complex‑curved,
hollow‑shaped parts
 Sheet metal blank is positioned over die cavity
and then punch pushes metal into opening
 Products: beverage cans, ammunition shells,
automobile body panels
 Also known as deep drawing (to distinguish it
from wire and bar drawing)

EMU
 Drawing

Difference between
wire drawing &
deep drawing?

(a) Drawing of
cup‑shaped part: (1)
before punch
contacts work, (2)
near end of stroke;
(b) work-part: (1)
starting blank, (2)
drawn part.

EMU
 Clearance in Drawing
 Sides of punch and die separated by a
clearance c given by:
c = 1.1 t
where t = stock thickness
 In other words, clearance is about 10% greater
than stock thickness

EMU
 Mechanics of Drawing

Straightening the
Bending at
bent sheet,
die and
stretching
Fh: Holding force punch
F: Punch force radius
Wall thickness
variation: yes
Wall thinning
maximum at
bottom corner of
cup (max: 25%)

EMU
 Measures of Drawing Severity

Drawing Ratio: Db/Dp (Depends on Punch & Die corner radii,

Friction conditions, Depth of draw and Material properties)
Optimal value: 2. Greater the ratio, more severer the operation

Reduction: r= (Db-Dp)/Db
Optimal value should be less than 2

Thickness/Blank Diameter: (to/Db): It should be greater than 1%.

Lower ratios lead to wrinkling of flange.

EMU
 Forces in Sheet Drawing
Drawing force required by punch:

Blank holding force:

Higher holding forces don’t allow material to be be pulled into the

die, causing undue stretching of blank and tearing.
Smaller holding forces cause wrinkling
EMU
of flange
 Defects in Sheet Drawing

Due to Small Due to Small Due to high Due to high Due to friction and
blank holding Punch force blank holding anisotropy of lack of lubrication
force force material at the sheet/punch
interface

EMU
 Assignment 3

20.3, 20.6, 20.9, 20.13, 20.17,

20.21

EMU