Scribd
Upload
14 views24 pages

ELE Lec 8

Uploaded by

abdalrahim124
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
14 views24 pages

ELE Lec 8

Uploaded by

abdalrahim124
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
You are on page 1/ 24

Engineering and

Architecture
Analog
Electronics
Fundamentals
EEE223
Lec 5

Full-Wave Rectifier

Lecturer Rayan Jaber


A Full-Wave Rectifier

– A full-wave rectifier allows unidirectional (one-way)


current through the load during the entire 360° of the input
cycle.
– The number of positive alternations that make up the full-wave rectified
voltage is twice that of the half-wave voltage for the same time interval.
The average value, for a full-wave rectified sinusoidal voltage is twice
that of the half-wave, as shown in the following formula:
Center-Tapped Full-Wave
Rectifier Operation

– A center-tapped rectifier is a type of full-wave rectifier


that uses two diodes connected to the secondary of a center-
tapped transformer. The input voltage is coupled through
the transformer to the center-tapped secondary. Half of the
total secondary voltage appears between the center tap and
each end of the secondary winding as shown.
– For a positive half-cycle of the input voltage, the polarities of the
secondary voltages are as shown in Figure (a) This condition
forward-biases diode D1 and reverse-biases diode D2. The current
path is through D1 and the load resistor RL, as indicated. For a
negative half-cycle of the input voltage, the voltage polarities on
the secondary are as shown in Figure (b). This condition reverse-
biases D1 and forward-biases D2. The current path is through D2
and RL, as indicated. Because the output current during both the
positive and negative portions of the input cycle is in the same
direction through the load, the output voltage developed across the
load resistor is a full-wave rectified dc voltage, as shown.
Effect of the Turns
Ratio on the Output
Voltage
– If the transformer’s turns ratio is 1, the peak value of the
rectified output voltage equals half the peak value of the
primary input voltage less the barrier potential, as illustrated
in Figure. Half of the primary voltage appears across each
half of the secondary winding (Vp(sec) = Vp(pri)).
– In order to obtain an output voltage with a peak equal to the
input peak (less the diode drop), a step-up transformer with
a turns ratio of n = 2 must be used. In this case, the total
secondary voltage (Vsec) is twice the primary voltage
(2Vpri), so the voltage across each half of the secondary is
equal to Vpri.
– In any case, the output voltage of a center-tapped full-wave
rectifier is always one-half of the total secondary voltage
less the diode drop, no matter what the turns ratio.

– Peak Inverse Voltage Each diode in the full-wave rectifier


is alternately forward-biased and then reverse-biased. The
maximum reverse voltage that each diode must withstand is
the peak secondary voltage Vp(sec).
Bridge Full-Wave
Rectifier Operation

– The bridge rectifier uses four diodes connected as shown


in Figure. When the input cycle is positive as in part (a),
diodes D1 and D2 are forward-biased and conduct current
in the direction shown.
– A voltage is developed across RL that looks like the positive
half of the input cycle. During this time, diodes D3 and D4
are reverse-biased.
– When the input cycle is negative as in Figure (b), diodes D3
and D4 are forward biased and conduct current in the same
direction through RL as during the positive half-cycle.
During the negative half-cycle, D1 and D2 are reverse-
biased. A full-wave rectified output voltage appears across
RL as a result of this action. Therefore:
Full-Wave Rectifier with
a Capacitor Filter

– For a given input frequency, the output frequency of a full-


wave rectifier is twice that of a half-wave rectifier, as
illustrated. This makes a full-wave rectifier easier to filter
because of the shorter time between peaks.
– When filtered, the full-wave rectified voltage has a smaller
ripple than does a half-wave voltage for the same load
resistance and capacitor values. The capacitor discharges
less during the shorter interval between full-wave pulses, as
shown in Figure
– Ripple Factor The ripple factor (r) is an indication of the
effectiveness of the filter and is defined as

– For a full-wave rectifier with a capacitor-input filter,


approximations for the peak-topeak ripple voltage, Vr(pp),
and the dc value of the filter output voltage, VDC, are given
in the following equations.
– The variable Vp(rect) is the unfiltered peak rectified
voltage. Noticethat if RL or C increases, the ripple voltage
decreases and the dc voltage increases.
Thank
You

You might also like