CE 2513 FLUID MECHANICS

INTRODUCTION
Mechanics: The oldest physical science that deals with both stationary and moving bodies under the
influence of forces.
Statics: The branch of mechanics that deals with bodies at rest.
Dynamics: The branch that deals with bodies in motion.
Fluid mechanics: The science that deals with the behavior of fluids at rest (fluid statics) or in motion
(fluid dynamics), and the interaction of fluids with solids or other fluids at the boundaries.
Fluid dynamics: Fluid mechanics is also referred to as fluid dynamics by considering fluids at rest as
a special case of motion with zero velocity.
Hydrodynamics: The study of the motion of fluids that can be approximated as incompressible
(such as liquids, especially water, and gases at low speeds).
Hydraulics: A subcategory of hydrodynamics, which deals with liquid flows in pipes and open
channels.
Gas dynamics: Deals with the flow of fluids that undergo significant density changes, such as
the flow of gases through nozzles at high speeds.
Aerodynamics: Deals with the flow of gases (especially air) over bodies such as aircraft,
rockets, and automobiles at high or low speeds.
Meteorology, oceanography, and hydrology: Deal with naturally occurring flows.
Stress: Force per unit area.
Normal stress: The normal
component of a force acting on a
surface per unit area.
Shear stress: The tangential
component of a force acting on a
surface per unit area.
Pressure: The normal stress in a
fluid at rest.
Zero shear stress: A fluid at rest is
at a state of zero shear stress.
When the walls are removed or a
liquid container is tilted, a shear
develops as the liquid moves to The normal stress and shear stress at
the surface of a fluid element. For
re-establish a horizontal free
fluids at rest, the shear stress is zero
surface. and pressure is the only normal stress.
What is a Fluid?

Fluid: A substance in the liquid or gas

phase.
A solid can resist an applied shear
stress by deforming.
A fluid deforms continuously under the
influence of a shear stress, no matter
how small.
In solids, stress is proportional to strain,
but in fluids, stress is proportional to Deformation of a rubber block
strain rate.
placed between two parallel plates
When a constant shear force is applied,
under the influence of a shear
a solid eventually stops deforming at
force. The shear stress shown is
some fixed strain angle, whereas a fluid
never stops deforming and approaches that on the rubber—an equal but
a constant rate of strain. opposite shear stress acts on the
upper plate.
In a liquid, groups of molecules can move relative to each other, but the volume remains relatively
constant because of the strong cohesive forces between the molecules. As a result, a liquid takes
the shape of the container it is in, and it forms a free surface in a larger container in a gravitational
field.
A gas expands until it encounters the walls of the container and fills the entire available space. This
is because the gas molecules are widely spaced, and the cohesive forces between them are very
small. Unlike liquids, a gas in an open container cannot form a free surface.

Unlike a liquid, a gas

does not form a
free surface, and it
expands to fill the
entire available
space.
Intermolecular bonds are strongest in solids and weakest in gases.
Solid: The molecules in a solid are arranged in a pattern that is repeated
throughout.
Liquid: In liquids molecules can rotate and translate freely.
Gas: In the gas phase, the molecules are far apart from each other, and
molecular ordering is nonexistent.

The arrangement of atoms in different phases: (a) molecules are at

relatively fixed positions in a solid, (b) groups of molecules move about
each other in the liquid phase, and (c) individual molecules move about at
random in the gas phase.
Application Areas of Fluid Mechanics

Fluid dynamics is used extensively

in the design of artificial hearts.
Shown here is the Penn State
Electric Total Artificial Heart.
Viscous versus Inviscid Regions of Flow
Viscous flows: Flows in which the frictional effects are significant.
Inviscid flow regions: In many flows of practical interest, there are regions
(typically regions not close to solid surfaces) where viscous forces are
negligibly small compared to inertial or pressure forces.

The flow of an originally

uniform fluid stream
over a flat plate, and
the regions of viscous
flow (next to the plate
on both sides) are
inviscid flows (away
from the plate).
Internal versus External Flow
External flow: The flow of an unbounded fluid over a surface such as a plate,
a wire, in a channel.
Internal flow: The flow in a pipe or duct if the fluid is completely bounded by
solid surfaces.

• Water flow in a pipe is

internal flow, and
airflow over a ball is
external flow .
• The flow of liquids in a
duct is called open-
channel flow if the duct
is only partially filled
with the liquid and
there is a free surface.
External flow over a tennis ball, and the
turbulent wake region behind.
Compressible versus Incompressible Flow

Incompressible flow: If the density of flowing fluid remains nearly constant throughout
(e.g., liquid flow).
Compressible flow: If the density of fluid changes during flow (e.g., high-speed gas flow)

When analyzing rockets, spacecraft, and other systems that involve high-speed gas
flows, the flow speed is often expressed by Mach number

Ma = 1 Sonic flow
Ma < 1 Subsonic flow
Ma > 1 Supersonic flow
Ma >> 1 Hypersonic flow
 Laminar versus Turbulent Flow

Laminar flow: The highly ordered fluid

motion characterized by smooth layers
of fluid. The flow of high-viscosity fluids
such as oils at low velocities is typically
laminar.

Transitional flow: A flow that

alternates between being laminar and
turbulent.

Turbulent flow: The highly disordered

fluid motion that typically occurs at high
velocities and is characterized by
velocity fluctuations. The flow of low-
viscosity fluids such as air at high
velocities is typically turbulent.

Laminar, transitional, and turbulent flows

over a flat plate.
Natural (or Unforced) Steady versus Unsteady Flow
versus Forced Flow
Forced flow: A fluid is forced to flow • The term steady implies no change at a
over a surface or in a pipe by external point with time.
means such as a pump or a fan. • The opposite of steady is unsteady.
• The term uniform implies no change with
location over a specified region.
Natural flow: Fluid motion is due to
natural means such as the buoyancy • The term periodic refers to the kind of
effect, which manifests itself as the rise unsteady flow in which the flow oscillates
about a steady mean.
of warmer (and thus lighter) fluid and the
fall of cooler (and thus denser) fluid. • Many devices such as turbines,
compressors, boilers, condensers, and
heat exchangers operate for long periods
of time under the same conditions, and
they are classified as steady-flow
devices.
Comparison of (a) instantaneous snapshot of an unsteady
flow, and (b) long exposure picture of the same flow.
One-, Two-, and Three-Dimensional Flows

• A flow field is best characterized by its velocity distribution.

• A flow is said to be one-, two-, or three-dimensional if the flow velocity varies in one,
two, or three dimensions, respectively.
• However, the variation of velocity in certain directions can be small relative to the
variation in other directions and can be ignored.

The development of the velocity profile in a circular pipe. V = V(r, z) and thus the flow is
two-dimensional in the entrance region, and becomes one-dimensional downstream when
the velocity profile fully develops and remains unchanged in the flow direction, V = V(r).
SYSTEM AND CONTROL VOLUME
• System: A quantity of matter or a region in
space chosen for study.
• Surroundings: The mass or region outside the
system
• Boundary: The real or imaginary surface that
separates the system from its surroundings.
• The boundary of a system can be fixed or
movable.
• Systems may be considered to be closed or
open.

• Closed system
(Control mass):
A fixed Quantity
amount of mass,
and no mass
can cross its
boundary.
 • Open system (control volume): A properly selected region in space.
• It usually encloses a device that involves mass flow such as a compressor, turbine, or
nozzle.
• Both mass and Energy can cross the boundary of a control volume. (Mass quantity
remains same, however, energy quantity may change e.g. in a geyser)
• Control surface: The boundaries of a control volume. It can be real or imaginary. For
example, the control surface for the flow of air over an airplane wing is the real surface
of the wing. The control surface for the flow of water through a pipe is an imaginary
surface that encloses the pipe.

An open system (a
control volume) with one
inlet and one exit.
IMPORTANCE OF DIMENSIONS AND UNITS

• Any physical quantity can be characterized by

dimensions.
• The magnitudes assigned to the dimensions are
called units.
• Some basic dimensions such as mass m, length L,
time t, and temperature T are selected as primary
or fundamental dimensions, while others such as
velocity V, energy E, and volume V are expressed
in terms of the primary dimensions and are called
secondary dimensions, or derived dimensions.
• Metric SI system: A simple and logical system
based on a decimal relationship between the
various units.
• English system: It has no apparent systematic
numerical base, and various units in this system
are related to each other rather arbitrarily.
 Some SI and English Units

Work = Force  Distance The SI unit prefixes are used in all

1 J = 1 N∙m branches of engineering.
1 cal = 4.1868 J
1 Btu = 1.0551 kJ

The definition of the force units.

 W weight
m mass
g gravitational
acceleration

A body weighing
150 kgf on earth
will weigh only 25
on the moon.

The relative magnitudes of the force

units newton (N), kilogram-force
(kgf), and pound-force (lbf).

The weight of a unit

mass at sea level.
Dimensional homogeneity
All equations must be dimensionally homogeneous.

Unity Conversion
Ratios
All nonprimary units (secondary units) can be
formed by combinations of primary units.
Force units, for example, can be expressed as

They can also be expressed more conveniently

as unity conversion ratios as

To be dimensionally
homogeneous, all the
Unity conversion ratios are identically equal to 1 and terms in an equation
are unitless, and thus such ratios (or their inverses) must have the same unit.
can be inserted conveniently into any calculation to
properly convert units.
 Every unity conversion ratio (as well
as its inverse) is exactly equal to one.
Shown here are a few commonly used
unity conversion ratios.
Always check the units in your
calculations.