Scribd
Upload
377 views

Digital System Design by Using VERILOG

This document discusses digital system design using the Verilog hardware description language. It describes Verilog's ability to model digital systems at different levels of abstraction, including the behavioral level, register-transfer level, and gate level. Examples are given of modeling a D flip-flop, full adder, and half adder at each level. A top-down design approach using Verilog is also outlined.

Uploaded by

kpkarthi2001
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
377 views

Digital System Design by Using VERILOG

This document discusses digital system design using the Verilog hardware description language. It describes Verilog's ability to model digital systems at different levels of abstraction, including the behavioral level, register-transfer level, and gate level. Examples are given of modeling a D flip-flop, full adder, and half adder at each level. A top-down design approach using Verilog is also outlined.

Uploaded by

kpkarthi2001
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
You are on page 1/ 13

Digital System Design by Using VERILOG

Karthikeyan.P AP/ECE VCET

Introduction
Verilog is a HARDWARE DESCRIPTION LANGUAGE (HDL). A hardware description language is a language used to describe a digital system: for example, a network switch, a microprocessor or a memory or a simple flip-flop. This just means that, by using a HDL, one can describe any (digital) hardware at any level

EXAMPLE
//D flip-flop Code// module d_ff ( d, clk, q, q_bar); input d ,clk; output q, q_bar; wire d ,clk; reg q, q_bar; always @ (posedge clk) begin q <= d; q_bar <= !d; end endmodule

Design Approach
Bottom-up
The traditional method of electronic design is bottom-up. Each design is performed at the gate-level using the standard gates. With the increasing complexity of new designs this approach is nearly impossible to maintain.

Top-down
The desired design-style of all designers is the top-down one. A real top-down design allows early testing, easy change of different technologies, a structured system design and offers many other advantages. But it is very difficult to follow a pure top-down design. Due to this fact most designs are a mix of both methods, implementing some key elements of both design styles

TOP-DOWN DESIGN APPORACH

Verilog Abstraction Levels


Behavioral level Register-Transfer Level(Data Flow) Gate Level (Structural Level)

Behavioral level
This level describes a system by concurrent algorithms (Behavioral). Each algorithm itself is sequential, that means it consists of a set of instructions that are executed one after the other. Functions, Tasks and Always blocks are the main elements. There is no regard to the structural realization of the design.

Example-Full Adder Behavioral Level


module ADD_FULL_RTL (sum,cout,x,y,cin); output sum,cout; input x,y,cin; //declaration for behavioral model wire cin,x,y; reg sum,cout; // behavioral specification always @ (x or y or cin) {cout, sum} = x + y + cin; endmodule

Register-Transfer Level
Designs using the Register-Transfer Level specify the characteristics of a circuit by operations and the transfer of data between the registers. An explicit clock is used. RTL design contains exact timing bounds: operations are scheduled to occur at certain times. Modern RTL code definition is "Any code that is synthesizable is called RTL code".

Example Half Adder RTL Level


module halfadder(a,b,sum,carry); input a,b; output sum, carry; wire sum, carry; assign sum = a^b; // sum bit assign carry = (a&b) ;//carry bit endmodule

Example Full Adder RTL Level


module ADD_FULL_RTL (sum,cout,x,y,cin); output sum,cout; input x,y,cin; //declaration for continuous assignment wire cin,x,y,sum,cout; //logical assignment assign sum = x ^ y ^ cin; assign cout = x & y | x & cin | y & cin; endmodule

Gate Level
Within the logic level the characteristics of a system are described by logical links and their timing properties. All signals are discrete signals. They can only have definite logical values (`0', `1', `X', `Z`). The usable operations are predefined logic primitives (AND, OR, NOT etc gates). Using gate level modeling might not be a good idea for any level of logic design. Gate level code is generated by tools like synthesis tools and this net list is used for gate level simulation and for backend.

Example Half Adder Gate Level


module ADD_HALF (s,c,x,y); output s,c; input x,y; wire s,c,x,y; // this line is optional since nodes default to wires xor G1 (s,x,y); // instantiation of XOR gate and G2 (c,x,y); // instantiation of AND gate endmodule

You might also like