Scribd
Upload
52 views

Humidifier Using Iot Final

Uploaded by

Anshuman Dey
Copyright
© © All Rights Reserved
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
52 views

Humidifier Using Iot Final

Uploaded by

Anshuman Dey
Copyright
© © All Rights Reserved
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
You are on page 1/ 21

A PROJECT ON Portable Humidifier With

Internet Of Things (iot) Applications


Department Of Information Technology

Under the supervision of


PRESENTED By
Hafizur Rahman
Anshuman Dey – 2021ITB004 (IT)
Professor
Arindam Mondal – 2021ITB007 (IT)
Department of Information
Shubhayu Shome – 2021ITB108 (IT)
Technology
INDEX
I. Introduction
II. List of Components used
 Arduino UNO Board
 DHT11 Sensor
 5V Relay Module
 OLED Display
 Ultrasonic Humidifier
III. Circuit Diagram
IV. Working
V. Observation
VI. Conclusion
VII. Future Scope and Uses

Page No. 1
INTRODUCTION
What is Internet Of Things
•(IOT)?
Network of
Physical Objects
• Feature an IP
address and
internet
connectivity
• Allow
communication
between IoT
enabled objects

Page No. 2
HUMIDIFIER
• Increases moisture
content of air
• Used to increase
moisture of carrier
gas
• Comfort during air
conditioning

Page No. 3
GOAL OF THE PROJECT

OUR GOAL IS TO CREATE AN HUMIDIFIER


USING IOT WHICH SENSES THE
TEMPERATURE AND HUMIDITY AROUND
AND REGULATES BY THE HUMIDIFIER
FUNCTION

Page No. 4
List Of The Components
Used In This Project

Page No. 5
ARDUINO UNO BOARD
• Open source
microcontroller
board
• Based on Microchip
ATMega328P
• Used to receive
input data and
process and
generate a response
according to
program
• It operates at a
frequency of 16MHz
Page No. 6
DHT11 SENSOR
• Commonly used for
sensing humidity and
temperature
• Uses a capacitive
humidity sensing
element
• Uses a thermistor for
sensing temperature

Page No. 7
5V RELAY MODULE
• electromechanical
device that uses an
electric current to
open or close the
contacts of a switch
• Works with a low
level trigger voltage
of 5V DC

Page No. 8
OLED DISPLAY
• Organic
electroluminescent diode
• Emissive electroluminesce
nt layer is a film of organic
PROJECT
compound
Temp: 28.1°C • emits light in response to
an electric current
HUM: 85%

Page No. 9
ULTRASONIC HUMIDIFIER

• Produce fine droplets of


water at room
temperature
• Uses piezo electronic
transducer to create high
frequency mechanical
oscillation on a film of
water

Page No. 10
CIRCUIT DIAGRAM

Page No. 11
WORKING

Page No. 12
WORKING

Page No. 13
OBSERVATION

• Humidity<=90
• Normally Open pin –
Allows load to humidifier
• Humidifier: ON

Page No. 14
OBSERVATION

• Humidity>90
• Normally Open pin –
Blocks load to humidifier
• Humidifier: OFF Page No. 15
CONCLUSION
• Can be directly supplied with current through cable or be used with
battery.
• Operates automatically
• Reads room temperature and humidity
• Transmits data Uno Board
• When humidity is above 90% circuit is opened, humidifier stops
operating
• When humidity is below 90% circuit is closed, humidifier spray
water droplets to bring humidity to the optimum level

Page No. 16
USES IN DAILY LIFE AND FUTURE
SCOPE

Steamer for nasal Household humidifier – Humidifier in


treatment maintain moisture greenhouse –
level Maintain moisture for
Page No. 17
REFERENCES
1. Project on Automatic Portable Humidifier using Arduino by
Debasis Parida
2. Performance Evaluation of Portable Mist Humidifier by
M.Mahesh, P.Thangavel,2020
3. Principle of Arduino by Leo Louis,2018.
4. Images have been taken from Google
5. Websites used for reference are Arduino.com and
CircuitDigest.com

Page No. 18
Questions
&
Answers

Page No. 19
THANK
YOU

Page No. 20

You might also like