KX-MB2200/2500, DP-MB250/310

Service Seminar
Section 17 User & Service Mode
 User Mode
Basic Features NEW

Feature/Code Selection
Display interval To set display interval for messages showed alternately.
# 【 1 】【 4 】【 8 】 【 1 】 “ 1sec” (default), 【 2 】 “ 2sec” , 【 3 】 “ 3sec”
【 4 】 “ 4sec” , 【 5 】 “ 5sec”
Administrator To change the administrator code for mode restriction
Code settings.
# 【 1 】【 5 】【 1 】 1. 【 】 # 【 1 】【 5 】【 1 】 【 OK 】
2. Enter the current administrator code. 【 OK 】
・ The default administrator code is “0000”.
3. Enter a new 4-digit administrator code using 0-9.
【 OK 】
4. Enter the new administrator code again.
【 OK 】 【 】
Note:
・ It is recommended that you change this administrator
code from the default administrator code.
Mode restriction To activate the mode restriction.
# 【 1 】【 5 】【 4 】
2
 User Mode
NEW
Basic Features

Feature/Code Selection
All address book To erase all items stored in the address book.
erase Disconnect the following cables before activating this
# 【 2 】【 8 】【 9 】 feature.
– Telephone line cord (fax supported models only)
– USB cable
– LAN cable (LAN supported models only)
【 0 】 “ No” (default), 【 1 】 “ Yes”
To erase all items:
1. 【 】 # 【 2 】【 8 】【 9 】
2. 【 1 】 “ Yes” 【 OK 】
3. 【 1 】 “ Yes” 【 OK 】 【 】

3
 User Mode
Basic Features (KX-MB25**/DP -MB*** only)
Feature/Code Selection
Paper size in the To set the recording paper size in the lower input tray.
lower input tray*3 【 0 】 “ 16K”, 【 1 】 “ LETTER”, 【 2 】 “ LEGAL”
# 【 3 】【 8 】【 2 】 【 3 】 “ A4” (default), 【 4 】 “ A5”, 【 6 】 “ B5(ISO)”
【 7 】 “ B5(JIS)”, 【 】 “ 216X330”, 【 # 】
“ 216X340”
Note:
・ This feature will be displayed only when the lower
input tray is installed.
・ If any of the following paper sizes is selected,
received fax documents will be stored in memory
(fax supported models only).
– “A5”
– “B5(JIS)”
– “B5(ISO)”
– “16K”
・ If you have set feature #147 to “INCHES”, the
numbers are displayed in inches.
*3 Only for models that support the lower input tray. 4
 User Mode
Basic Features (KX-MB25**/DP -MB*** only)
Feature/Code Selection
Paper type for To set the paper type for the lower input tray.
lower input tray *3 【 1 】 “ PLAIN PAPER” (default)
# 【 3 】【 8 】【 5 】 【 2 】 “ THIN PAPER”
Note:
・ This feature will be displayed only when the lower
input tray is installed.
・ This setting will be deactivated when printing from a
computer.
*3 Only for models that support the lower input tray.

5
 User Mode
Fax Features (with FAX models only)
Feature/Code Selection
Duplex print To set the duplex print for fax reception.
setting for fax 【 0 】 “ OFF” (default)
reception 【 1 】 “ LONG EDGE”
# 【 4 】【 0 】【 7 】 【 2 】 “ SHORT EDGE”
Confirming the When “ON” is selected, after the document is scanned
next document using the automatic document feeder during fax memory
# 【 4 】【 2 】【 4 】 transmission, the message shows to confirm the next
document.
Insert the next document and press 【 OK 】 .
【 】
【 0 】 “ OFF” (default)
【 1 】 “ ON”
Direct SMTP*1 For registering email address when “ON” is selected,
# 【 4 】【 2 】【 5 】 you can set the direct SMTP for the email address.
【 0 】 “ OFF” (default)
【 1 】 “ ON”
*1 Only for models that support the Internet fax feature.
6
 User Mode
Fax Features (with FAX models only)
Feature/Code Selection
Delivery notice *1 When “ON” is selected, a delivery notice is sent to the
# 【 4 】【 2 】【 6 】 receiver of the Internet fax. If the receiver returns the
notice, a sending report will be printed.
【 0 】 “ OFF”
【 1 】 “ ON“ (default)
POP timer setting *1 To set the POP timer.
# 【 4 】【 2 】【 8 】 1. 【 】 【 4 】【 2 】【 8 】
2. Set the POP timer (the interval of receiving Internet fax
automatically) to a value between “00” and
“60” minutes using the dial keypad.
・ The default is “03” minutes.
・ If you do not want to receive an Internet fax
automatically, set the timer to “00”.
3. 【 OK 】 【 】

*1 Only for models that support the Internet fax feature.

7
 User Mode
Fax Features (with FAX models only)
Feature/Code Selection
Input tray setting This feature will be displayed only when the lower input
for fax *2 tray is installed. (KX-MB25**/DP -MB*** only)
# 【 4 】【 4 】【 0 】
【 1 】 “ #1”: Standard input tray
【 2 】 “ #3”: Lower input tray
【 3 】 “ AUTO” (default): The unit will automatically
select the proper tray according to the paper size of
the received faxes.

*2 Only for models that support the lower input tray.

8
 User Mode
Copy Features
Feature/Code Selection
Duplex hold To hold the previous duplex setting.
# 【 4 】【 7 】【 0 】 【 0 】 “ DISABLED” (default)
【 1 】 “ ENABLED”
Note:
・ When this feature is activated, it will be effective for
the
following:
– When making 1-sided originals into 2-sided copies.
– When making 2-sided originals into 2-sided copies.
・ Even if this feature is activated, it will not be effective
when making 2-sided originals into 1-sided copies.
・ When making 2-sided originals into 2-sided copies,
the
original document settings will be reset even if this
feature is activated.

9
 User Mode
PC Print Features
Feature/Code Selection
Input tray in PCL*1 To set the input tray in PCL.
# 【 7 】【 6 】【 0 】 【 1 】 “ #1” (default): Standard input tray
【 2 】 “ #2”: Manual tray/multi-purpose tray
【 3 】 “ #3”: Lower input tray
【 4 】 “ #1+#2+#3”, “#1+#2”, “#1+#3” or “#2+#3”*1
*1 These options are displayed only when the paper size
and the media type match. If either is changed,
this setting will be changed accordingly.
Paper size in PCL *1 To set the recording paper size in PCL.
# 【 7 】【 6 】【 3 】 【 0 】 “ 16K”, 【 1 】 “ LETTER”, 【 2 】 “ LEGAL”
【 3 】 “ A4” (default), 【 4 】 “ A5”, 【 5 】 “ A6”, 【 6 】
“ B5(ISO)”
【 7 】 “ B5(JIS)”, 【 8 】 “ B6(ISO)”, 【 9 】 “ B6(JIS)”
【 】 “ 216X330”, 【 # 】 “ 216X340”
Note:
・ When you set feature #147 to “INCHES”, the
numbers
*1 Only for models that supportare
thedisplayed
PCL driver.
in inches. 10
 User Mode
LAN Features
Feature/Code Selection
Bonjour To set the Bonjour feature.
# 【 5 】【 1 】【 3 】 【 0 】 “ DISABLED”
【 1 】 “ ENABLED” (default)
Network status To view the network status.
# 【 5 】【 2 】【 6 】
WINS server #1 To set the primary WINS server for the LAN connection.
# 【 5 】【 3 】【 8 】 This feature is available when feature #500 is
deactivated.
1. 【 】 【 # 】【 5 】【 3 】【 8 】 【 OK 】
2. Enter the primary WINS server of the network on the
LAN using the dial keypad. 【 OK 】 【 】
WINS server #2 To set the secondary WINS server for the LAN
# 【 5 】【 3 】【 9 】 connection. This feature is available when feature #500
is deactivated.
1. 【 】 【 # 】【 5 】【 3 】【 9 】 【 OK 】
2. Enter the secondary WINS server of the network on
the LAN using the dial keypad. 【 OK 】 【 11
 User Mode
LAN Features
Feature/Code Selection
Address book When “ENABLED” is selected, you can check and edit the
editing on web address book through the web browser interface.
# 【 5 】【 6 】【 7 】 【 0 】 “ DISABLED”
【 1 】 “ ENABLED” (default)
Caller ID list on When “ENABLED” is selected, you can check the Caller
web*1 ID list through the web browser interface.
# 【 5 】【 6 】【 8 】 【 0 】 “ DISABLED”
【 1 】 “ ENABLED” (default)
Journal on web*1 When “ENABLED” is selected, you can check the journal
# 【 5 】【 6 】【 9 】 report through the web browser interface.
【 0 】 “ DISABLED”
【 1 】 “ ENABLED” (default)

*1 Only for models that support the fax feature.

12
 User Mode
LAN Features
Feature/Code Selection
LAN mode To select LAN mode.
# 【 5 】【 8 】【 0 】 Important:
・ To set this feature, make sure that:
– The unit is in standby mode.
– The document is not set to the automatic document
feeder.
– The recording paper is not set to the manual tray.
– The delay fax send feature is not activated.
(feature #412)
The model which is not supporting wireless LAN
【 0 】 “ OFF”
【 1 】 “ WIRED” (default)
with wireless LAN models
【 0 】 “ OFF”
【 1 】 “ WIRED” (default)
【 2 】 “ WIRELESS”
13
 User Mode
LAN Features
Feature/Code Selection
Wireless status*2 If feature #580 is set to “WIRELESS”, you can check the
# 【 5 】【 8 】【 1 】 status of the wireless LAN connection by pressing
【▼】 or 【▲】 .
WPS-PBC *2 To set up the wireless LAN connection using WPS-PBC.
# 【 5 】【 8 】【 2 】
WPS-PIN *2 To set up the wireless LAN connection using WPS-PIN.
# 【 5 】【 8 】【 3 】
SSID search *2 To set up the wireless LAN connection by finding the SSID
# 【 5 】【 8 】【 4 】 automatically on the network.
Manual setup for To set up the wireless LAN connection by entering the
wireless *2 required information manually.
# 【 5 】【 8 】【 5 】

*2 Only for models that support wireless LAN. (with wireless LAN models only) 14
 User Mode
LAN Features
Feature/Code Selection
Wireless restore*2 To restore all wireless LAN connection settings.
# 【 5 】【 8 】【 6 】 【 0 】 “ NO” (default)
【 1 】 “ YES”
1. 【 】 【 # 】【 5 】【 8 】【 6 】
2. 【 1 】 “ YES” 【 OK 】
3. 【 1 】 “ YES” 【 OK 】

*2 Only for models that support wireless LAN. (with wireless LAN models only) 15
 User Mode
USB print Features (KX-MB25**/DP -MB*** only)
Feature/Code Selection
Number of copies To set the number of copies to print.
in USB print 1. 【 】 【 # 】【 6 】【 6 】【 0 】 【 OK 】
# 【 6 】【 6 】【 0 】 2. Enter the desired number of copies from “01” to “99”,
using the dial keypad.
・ The default setting is “01”.
3. 【 OK 】 【 】

Recording paper To set the recording paper orientation.

orientation in USB 【 1 】 “ PORTRAIT” (default)
print 【 2 】 “ LANDSCAPE”
# 【 6 】【 6 】【 1 】

16
 User Mode
USB print Features (KX-MB25**/DP -MB*** only)
Feature/Code Selection
N in 1 setting in Using this feature, you can save paper by printing 2, 4 or
USB print 8 pages onto 1 page. The documents’ size will be reduced
# 【 6 】【 6 】【 2 】 to fit the recording paper.
【 0 】 “ OFF” (default), 【 1 】 “ 2 in 1”, 【 2 】 “ 4 in 1”,
【 3 】 “ 8 in 1”
N in 1 page border To select whether or not to print a line between the pages
in USB print in N in 1 printing.
# 【 6 】【 6 】【 3 】 【 0 】 “ NONE” (default), 【 1 】 “ SOLID LINE”
Duplex in USB To select whether to print pages in duplex and also select
print the type of binding.
# 【 6 】【 6 】【 4 】 【 0 】 “ OFF” (default)
【 1 】 “ LONG EDGE”
【 2 】 “ SHORT EDGE”

17
 User Mode
USB print Features (KX-MB25**/DP -MB*** only)
Feature/Code Selection
Continuous in To select whether documents in different file formats are
USB print printed onto 1 page when using layout printing and duplex
# 【 6 】【 6 】【 5 】 printing.
【 0 】 “ DISABLED”, 【 1 】 “ ENABLED” (default)
Input tray in USB To set the input tray to use for USB print.
print 【 1 】 “ #1” (default): Standard input tray
# 【 6 】【 6 】【 9 】 【 2 】 “ #2”: Multi-purpose tray
【 3 】 “ #3”: Lower input tray
【 4 】 “ #1+#2+#3”, “#1+#2”, “#1+#3” or “#2+#3”*1
*1 These options are displayed only when the paper size
(feature #380 on page 78, feature #381 on page 78
or feature #382 on page 79) and the media type
(feature #383 on page 79, feature #384 on page 79
or feature #385 on page 79) match. If either is
changed, this setting will be changed accordingly.
18
 User Mode
USB print Features (KX-MB25**/DP -MB*** only)
Feature/Code Selection
Display sort 【 0 】 “ OFF”
setting in USB 【 1 】 “ NAME ORDER”: The files and folders will be
print sorted
# 【 6 】【 7 】【 2 】 alphabetically by name.
【 2 】 “ DATE ORDER” (default): The files and folders will
be
sorted by date.
Note:
・ Selecting “NAME ORDER” or “DATE ORDER” will
require some time to sort the files and folders.

19
 User Mode (Counter View)
Counter View Function NEW
u can check the Print Count value of Total/ Print/ Copy/ Fax/ Other on LCD display
MENU”, “#”, “4”, “8”, “4”, “OK” )

③Copy

④Fax

①Total

②Print

20
 Service Mode ( 880)
History Print add ISO / IEC19752 standard simulated print count

21
 Service Mode ( #880)
History Report

USB
Connector

No of Scan No of ADF Scan No of FB Scan No of PC Scan No of Doc. JAM

No of Print Call 3 Info. -1 Call 3 Info. -2 Call 3 Info. -3

No of Recording Paper JAM No of Pick Error Manual Feed

No of Pick Error Cassette1 No of Copies
JAM Info. -1 JAM Info. -2 JAM Info. -3 No of ADF Feed 22
 Section 17
End

To go back to the top page,

please double click the “Back button” on your browser.