Scribd
Upload
34 views35 pages

SGC 2 - Configuration

Uploaded by

WesleyNah
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
34 views35 pages

SGC 2 - Configuration

Uploaded by

WesleyNah
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
You are on page 1/ 35

Configuration for

Single Genset
application
Content

Software overview

Firmware vs. Archive

InteliConfig & Starter kit


NanoEdit
LiteEdit
InteliConfig
InteliMonitor
GenConfig
WinScope
Firmware & Archive

What is the difference?


Firmware & Archive

Archive Firmware
• Controller’s program
Controller’s „OS“
• I/O configuration, PLC
• Parameters (setpoints)
• History
Firmware & Archive

Firmware Archive
1.1.1.1; 1.1.0.8 1.1.xx

1.2.0.; 1.2.1 1.2.xx

4.1.0; 4.1.2 4.1.xx

First two digits have to be the same


Firmware & Archive

Firmware Archive
1.1.1.1; 1.1.0.8 1.1.xx

1.2.0; 1.2.1; 1.2.xx

4.1.0; 4.1.2 4.1.xx

First two digits are different => not compatible!


Firmware & Archive upgrade

› Archive upgrade
» Neccessary if archive version < fw version
in the controller
» Possible to have 1.1.0.8 archive in 1.1.1.1
fw version
› Firmware upgrade
» Neccessary when archive version > fw
version
InteliConfig
InteliConfig

› Download (free for ComAp Members Club - www.comap-control.com)


» Products  Configuration tools  InteliConfig
» Search for “InteliConfig” and see the “Downloads“  „Manuals“ or „Software“ section
InteliConfig

› Remote control and monitoring

› Configuration and parameters adjustment

› PLC Editor

› Support of electronic engines


Start InteliConfig
InteliConfig Starting screen
Types of
connection

Start with New


configuration

Detected
Database with controllers
manuals

InteliConfig
settings
Controller connection

› Online
• Direct (RS232, USB)
• Internet/Ethernet
• AirGate

› Offline
• Create new
Double click
• Open archive
on detected
controllers
InteliConfig window

Starting
Logs
screen

Information
Control screen about
InteliConfig

Tools screen Zoom

Type of
connection
InteliConfig - Control screen

Configuration Manuals and


and setpoints Controller info

Controller
Configuration
modes
import

Alarm list
SCADA

Analog values Binary inputs


and and outputs
measurement
InteliConfig - Control screen

Logging into
controller

Online setpoints PLC Monitor

Online values Genset state

Controller Genset
history statistics
Control screen - Tools

Communication
Clone
Password reset tables
management Statistics
procedure

Firmware and
archive upgrade
InteliConfig - Controller configuration screen

Languages,
USER modbus,
units, firewall
Modules and
ECU PLC Editor
configuration
Inputs Logical
Outputs Binary/Analog
Configuration inputs

Analog sensor Alarm


curves definitions
(Wrn, SD, BOC)
Setpoints & Upload
User configuration
setpoints into controller
InteliConfig - Setpoins

Setpoint
details

Setpoint
groups
Setpoint
description
Search tool

Advanced
view
InteliConfig - PLC Editor

PLC inputs PLC outputs

Consistency
PLC blocks
check
InteliConfig - Protections

Analog /
Binary
protections

Protection
definition

Add protection
source value

Protection
Create new activation type
protection
Create binary
protection state
register
InteliConfig - Protection blocking

› All the time


» Protection is not being blocked (only when
LBI SD override = 1)
› Run Only Block Delay (setpoint)
» Protection is blocked during starting phase
for a specified time (given by the setpoint)
› Force block
» Protection blocking forced by LBI
Protection force disable
› Electrical protection
» Blocking is enabled until the MaxStabTime
elapses or breaker is closed
Hands-on part
Practical tasks

Task 1 – First steps after purchasing controller


A. Install „InteliConfig“
B. Connect to the controller
C. Turn on the production mode
D. Write [email protected] as an email address into the controller
E. Upgrade firmware in your controller to the latest one
F. Upload a default StarterKit configuration into the controller
G. Modify parameters for the simulation
Practical tasks

Task 2 - Simulation
A. Tune the basic simulation parameters on the StarterKit
• Controller in OFF mode
• Mains OK
• Mains Voltage = 231 V
• Fuel Level > 50 %
B. Start the genset in MAN mode
A. Stop the engine after succesfull running
C. Verify if Automatic Mains Fail (AMF) function works according to your needs
D. Test function on the Binary Inputs
• Access Lock
• Emergency stop
• Remote OFF
• Remote Test
• SD Override
PLC Tasks

Task 3 – PLC Editor


A. Create function that will show alarm on the display if unit is not in automatic mode
B. Create output to START/STOP Fuel Pump (Binary Output) for fuel auto refilling
C. Opened door protection
D. Louvre control simulation (Use delay blocks)
User policy – extra tasks

› UNASSIGNED USER – (User 0) can’t modify any setpoints and can’t control a unit.
› Operator – (User 1) this user has an access only to the control commands.
› Local administrator – (User 2) has an access to the commands, Engine settings,
Generator settings and AMF settings.
› Administrator – Has a full access

› Add any 3rd language to the controller.


THANK YOU FOR YOUR TIME

Technical support
Working days
8:00 – 18:00
[email protected]
+420 246 012 666

You might also like