AS Physics

Unit 1 Unit 2
Particles, Quantum Phenomena and Electricity Mechanics, Materials and Waves

1 Constituents of the Atom 1 Scalars and Vectors

2 Particles and Antiparticles 2 Resolving Vectors

3 Quarks 3 Moments

4 Hadrons 4 Velocity and Acceleration

5 Leptons 5 Motion Graphs

6Forces and Exchange Particles 6 Equations of Motion

7 The Strong Interaction 7 Terminal Velocity and Projectiles

8 The Weak Interaction 8 Newton’s Laws

9 Feynman Diagrams 9 Work, Energy and Power

10 The Photoelectric 10 Conservation of Energy

Effect
11 Hooke’s Law
11Excitation, Ionisation and Energy Levels
12 Stress and Strain
12 Wave Particle Duality
13Bulk Properties of Solids
13 QVIRt
14 Young’s Modulus
14 Ohm’s Law and I-V Graphs
15 Progressive Waves
15Resistivity and Superconductivity
16Longitudinal and Transverse Waves
16 Series and Parallel Circuits
17 Superposition and Standing Waves
17 Energy and Power
18 Refraction
18 EMF and Internal Resistance
19 Total Internal Reflection
19Kirchhoff and Potential Dividers
20 Interference
20 Alternating Current
21 Diffraction
21 The Oscilloscope
 Unit 1
Lesson 1
Constituents of the Atom
To be know the constituents of the atom with their masses and charges
Learning
Outcomes To be able to calculate the specific charge of the constituents
To be able to explain what isotopes and ions are N. DWYER

The Nuclear Model (Also seen in GCSE Physics 1 and 2) Constituent Charge (C) Mass (kg)
We know from Rutherford’s experiment that the structure of Proton 1.6 x 10 -19
1.673 x 10-27
an atom consists of positively charged protons and neutral Neutron 0 1.675 x 10-27
neutrons in one place called the nucleus. The nucleus sits in Electron - 1.6 x 10-19 9.1 x 10-31
the middle of the atom and has negatively charged electrons
orbiting it. At GCSE we used charges and masses for the constituents relative to each other, the table above
shows the actual charges and masses.
Almost all of the mass of the atom is in the tiny nucleus which takes up practically no space when compared to
the size of the atom. If we shrunk the Solar System so that the Sun was the size of a gold nucleus the furthest
electron would be twice the distance to Pluto.
If the nucleus was a full stop it would be 25 m to the first electron shell, 100 to the second and 225 to the
third.

Notation (Also seen in GCSE Physics 2)

We can represent an atom of element X in the following way: ZA X
Z is the proton number. This is the number of protons in the nucleus. In an uncharged atom the number of
electrons orbiting the nucleus is equal to the number of protons.
In Chemistry it is called the atomic number
A is the nucleon number. This is the total number of nucleons in the nucleus (protons + neutrons) which can be
written as A = Z + N.

n Chemistry it is called the atomic mass number

N is the neutron number. This is the
number of neutrons in the nucleus.
Isotopes (Also seen in GCSE Physics 1 and
2)
Chlorine If we look at Chlorine in the periodic table we see that it is represented
Isotopesbyare Cl . Howforms
17different
35.5
can it of
havean 18.5
element. They
neutrons? alwaysThere
It can’t! haveare
thetwo
same number
stable of protons
isotopes but haveCl
of Chlorine, 35 a different numberfor
which accounts of ~75%
neutrons.
and Since
37 they
Cl which
have the same number of protons (and electrons) they behave 17 in the same way
17
accounts for ~25%. So the average of a large amount of Chlorine atoms 17Cl .
is 35.5
chemically.
Specific Charge
Specific charge is another title for the charge-mass ratio. This is a measure of the charge per unit mass and is
simply worked out by worked out by dividing the charge of a particle by its mass.
You can think of it as a how much charge (in Coulombs) you get per kilogram of the ‘stuff’.
Constituent Charge (C) Mass (kg) Charge-Mass Ratio (C kg-1) or (C/kg)
Proton 1.6 x 10 -19
1.673 x 10 -27
1.6 x 10-19 ÷ 1.673 x 10-27 9.58 x 107
Neutron 0 1.675 x 10-27 0 ÷ 1.675 x 10-27 0
Electron (-) 1.6 x 10 -19
9.1 x 10 -31
1.6 x 10 ÷ 9.11 x 10-31
-19
(-) 1.76 x 1011
We can see that the electron has the highest charge-mass ratio and the neutron has the lowest.
Ions (Also seen in GCSE Physics 2)
An atom may gain or lose electrons. When this happens the atoms becomes electrically charged (positively or
negatively). We call this an ion.
If the atom gains an electron there are more negative charges than positive, so the atom is a negative ion.
Gaining one electron would mean it has an overall charge of -1, which actually means -1.6 x 10-19C.
Gaining two electrons would mean it has an overall charge of -2, which actually means -3.2 x 10-19C.
If the atom loses an electron there are more positive charges than negative, so the atom is a positive ion.
Losing one electron would mean it has an overall charge of +1, which actually means +1.6 x 10-19C.
Losing two electrons would mean it has an overall charge of +2, which actually means +3.2 x 10-19C.
 Unit 1
Lesson 2
Particles and Antiparticles
To know what is the difference between particles and antiparticles
Learning
Outcomes To be able to explain what annihilation is
To be able to explain what pair production is N. DWYER

Antimatter
British Physicist Paul Dirac predicted a particle of equal mass to an electron but of opposite charge (positive).
This particle is called a positron and is the electron’s antiparticle.
Every particles has its own antiparticle. An antiparticle has the same mass as the particle version but has
opposite charge. An antiproton has a negative charge, an antielectron has a positive charge but an antineutron
is also uncharged like the particle version.
American Physicist Carl Anderson observed the positron in a cloud chamber, backing up Dirac’s theory.
Anti particles have opposite Charge, Baryon Number, Lepton Number and Strangeness.
If they are made from quarks the antiparticle is made from antiquarks
Annihilation
Whenever a particle and its antiparticle meet they annihilate each other.
Annihilation is the process by which mass is converted into energy, particle
and antiparticle are transformed into two photons of energy.
Mass and energy are interchangeable and can be converted from one to
the other. Einstein linked energy and mass with the equation:
E  mc2
You can think of it like money; whether you have dollars or pounds you would still have the same amount of
money. So whether you have mass or energy you still have the same amount.
The law of conservation of energy can now be referred to as the conservation of mass-energy.
The total mass-energy before is equal to the total mass-energy after.
Photon
Max Planck had the idea that light could be released in ‘chunks’ or packets of energy. Einstein named these
wave-packets photons. The energy carried by a photon is given by the equation:

E  hf Since c  f we can also write this as: E  

hc

How is there anything at all?

When the Big Bang happened matter and antimatter was produced and sent out expanding in all directions. A
short time after this there was an imbalance in the amount of matter and antimatter. Since there was more
matter all the antimatter was annihilated leaving matter to form protons, atoms and everything around us.
Pair Production
Pair production is the opposite process to annihilation, energy is
converted into mass. A single photon of energy is converted into a
particle-antiparticle pair. (This happens to obey the conservation laws)
This can only happen if the photon has enough mass-energy to “pay
for the mass”.
Let us image mass and energy as the same thing, if two particles needed 10 “bits” and the photon had 8 bits
there is not enough for pair production to occur.
If two particles needed 10 bits to make and the photon had 16 bits the particle-antiparticle
pair is made and the left over is converted into their kinetic energy.

If pair production occurs in a magnetic field the particle and antiparticle will move in circles of
opposite direction but only if they are charged. (The deflection of charges in magnetic fields
will be covered in Unit 4: Force on a Charged Particle)

Pair production can occur spontaneously but must occur near a nucleus which recoils to help
conserve momentum. It can also be made to happen by colliding particles. At CERN protons are accelerated and
fired into each other. If they have enough kinetic energy when they collide particle-antiparticle pair may be
created from the energy.
The following are examples of the reactions that have occurred:
pp pppp pppp  p p p pnn
In all we can see that the conservation laws of particle physics are obeyed.
 Unit 1
Lesson 3
Quarks
To know what quarks are and where they are found
Learning
Outcomes To be able to explain how they were discovered
To know the properties of each type of quark N. DWYER

Rutherford Also seen in GCSE Physics 2

Rutherford fired a beam of alpha particles at a thin gold foil. If the atom had no inner structure the alpha
particles would only be deflected by very small angles. Some of the alpha particles were scattered at large
angles by the nuclei of the atoms. From this Rutherford deduced that the atom was mostly empty space with
the majority of the mass situated in the centre. Atoms were made from smaller particles.

Smaller Scattering
In 1968 Physicists conducted a similar experiment to Rutherford’s but they fired
a beam of high energy electrons at nucleons (protons and neutrons). The results
they obtained were very similar to Rutherford’s; some of the electrons were
deflected by large angles. If the nucleons had no inner structure the electrons
would only be deflected by small angles. These results showed that protons and
neutrons were made of three smaller particles, each with a fractional charge.

Quarks
These smaller particles were named quarks and are thought to be fundamental particles (not made of anything
smaller). There are six different quarks and each one has its own antiparticle.
We need to know about the three below as we will be looking at how larger particles are made from different
combinations of quarks and antiquarks.
Quark Charge Baryon Strangeness Anti Charge Baryon Strangeness
(Q) Number (B) (S) Quark (Q) Number (B) (S)
d -⅓ +⅓ 0 d¯ +⅓ -⅓ 0
u +⅔ +⅓ 0 ū -⅔ -⅓ 0
s -⅓ +⅓ -1 s¯ +⅓ -⅓ +1

The other three are Charm, Bottom and Top. You will not be asked about these three
Quark Charge Baryon No. Strangeness Charmness Bottomness Topness
d -⅓ +⅓ 0 0 0 0
u +⅔ +⅓ 0 0 0 0
s -⅓ +⅓ -1 0 0 0
c +⅔ +⅓ 0 +1 0 0
b -⅓ +⅓ 0 0 -1 0
t +⅔ +⅓ 0 0 0 +1

The Lone Quark?

Never! Quarks never appear on their own. The energy required to pull two quarks
apart is so massive that it is enough to make two new particles. A quark and an
antiquark are created, another example of pair production.
A particle called a neutral pion is made from an up quark and an antiup quark.
Moving these apart creates another up quark and an antiup quark. We now
have two pairs of quarks.
Trying to separate two quarks made two more quarks.

Particle Classification
Now that we know that quarks are the smallest building blocks we can
separate all other particles into two groups, those made from quarks and
those that aren’t made from quarks.
Hadrons – Heavy and made from smaller particles
Leptons – Light and not made from smaller particles
 Unit 1
Lesson 4
Hadrons
To know what a hadron is and the difference between the two types
Learning
Outcomes To know the properties common to all hadrons
To know the structure of the common hadrons and which is the most stable N. DWYER

Made from Smaller Stuff

Hadrons, the Greek for ‘heavy’ are not fundamental particles they are all made from smaller particles, quarks.
The properties of a hadron are due to the combined properties of the quarks that it is made from.
There are two categories of Hadrons: Baryons and Mesons.
Baryons Made from three quarks
Proton Charge Baryon Strangeness Neutron Charge Baryon Strangeness
(Q) Number (B) (S) (Q) Number (B) (S)
u +⅔ +⅓ 0 d -⅓ +⅓ 0
u +⅔ +⅓ 0 u +⅔ +⅓ 0
d -⅓ +⅓ 0 d -⅓ +⅓ 0
p +1 +1 0 n 0 +1 0
The proton is the only stable hadron, all others eventually decay into a proton.
Mesons Made from a quark and an antiquark
Pion Charge Baryon Strangeness Pion Charge Baryon Strangeness
Plus (Q) Number (B) (S) Minus (Q) Number (B) (S)
u +⅔ +⅓ 0 ū -⅔ -⅓ 0
d¯ +⅓ -⅓ 0 d -⅓ +⅓ 0
+ -
u +1 0 0 u -1 0 0

Pion Charge Baryon Strangeness Pion Charge Baryon Strangeness

Zero (Q) Number (B) (S) Zero (Q) Number (B) (S)
u +⅔ +⅓ 0 d -⅓ +⅓ 0
ū -⅔ -⅓ 0 d¯ +⅓ -⅓ 0
u0 0 0 0 u0 0 0 0

Kaon Charge Baryon Strangeness Kaon Charge Baryon Strangeness

Plus (Q) Number (B) (S) Minus (Q) Number (B) (S)
u +⅔ +⅓ 0 ū -⅔ -⅓ 0
s¯ +⅓ -⅓ +1 s -⅓ +⅓ -1
K+ +1 0 +1 K- -1 0 -1

Kaon Charge Baryon Strangeness AntiKaon Charge Baryon Strangeness

Zero (Q) Number (B) (S) Zero (Q) Number (B) (S)
d -⅓ +⅓ 0 d¯ +⅓ -⅓ 0
s¯ +⅓ -⅓ +1 s -⅓ +⅓ -1
K0 0 0 +1 K¯0 0 0 -1

Anti Hadrons
Anti hadrons are made from the opposite quarks as their Hadron counterparts, for example a proton is made
from the quark combination uud and an antiproton is made from the combination ū ū d¯
We can see that a π+ and a π- are particle and antiparticle of each other.
Anti Charge Baryon Strangeness Anti Charge Baryon Strangeness
Proton (Q) Number (B) (S) Neutron (Q) Number (B) (S)
ū -⅔ -⅓ 0 d¯ +⅓ -⅓ 0
ū -⅔ -⅓ 0 ū -⅔ -⅓ 0
d¯ +⅓ -⅓ 0 d¯ +⅓ -⅓ 0
p¯¯ -1 -1 0 n¯ 0 -1 0
You need to know all the quark combination shown on this page as they may ask you to recite any of them.
 Unit 1
Lesson 5
Leptons
To be able to explain what a lepton is
Learning
Outcomes To know the properties common to all leptons
To be able to explain the conservation laws and be able to use them N. DWYER

Fundamental Particles
A fundamental particle is a particle which is not made of anything smaller. Baryons and Mesons are made from
quarks so they are not fundamental, but quarks themselves are. The only other known fundamental particles
are Bosons (see Lesson 6: Forces and Exchange Particles) and Leptons.
Leptons
Leptons are a family of particles that are much lighter than Baryons and Mesons and are not subject to the
strong interaction. There are six leptons in total, three of them are charged and three are uncharged.
The charged particles are electrons, muons and tauons. The muon and tauon are similar to the electron
but
bigger. The muon is roughly 200 times bigger and the tauon is 3500 times bigger (twice the size of a proton).
Each of the charged leptons has its own neutrino. If a decay involves a neutrino and a muon, it will be a muon
neutrino, not a tauon neutrino or electron neutrino.
The neutrino is a chargeless, almost massless particle. It isn’t affected by the strong interaction or EM force and
barely by gravity. It is almost impossible to detect.
Lepton Charge Lepton Anti Lepton Charge Lepton
(Q) Number (L) (Q) Number (L)
Electron e- -1 +1 Anti Electron e+ +1 -1
Electron Neutrino νe 0 +1 Anti Electron Neutrino ν¯e 0 -1
- +
Muon μ -1 +1 Anti Muon μ +1 -1
Muon Neutrino νμ 0 +1 Anti Muon Neutrino ν¯μ 0 -1
- +
Tauon τ -1 +1 Anti Tauon τ +1 -1
Tauon Neutrino ντ 0 +1 Anti Tauon Neutrino ν¯τ 0 -1

Conservation Laws
For a particle interaction to occur the following laws must be obeyed, if either is violated the reaction will never
be observed (will never happen):
Charge: Must be conserved (same total value before as the total value after)
Baryon Number: Must be conserved
Lepton Number: Must be conserved
Strangeness: Conserved in EM and Strong Interaction. Doesn’t have to be
Examples conserved in Weak Interaction
In pair production a photon of energy- is converted +into a particle and its antiparticle
γ → e + e
Q 0 → -1 + +1 0 → 0 Conserved
B 0 → 0 + 0 0 → 0 Conserved
L 0 → +1 + -1 0 → 0 Conserved
S 0 → 0 + 0 0 → 0 Conserved
Let us look at beta plus decay as we knew it at GCSE. A neutron decays into a proton and releases an electron.
n → p + e-
Q 0 → +1 + -1 0 → 0 Conserved
B +1 → +1 + 0 +1 → +1 Conserved
L 0 → 0 + +1 0 → +1 Not Conserved
S 0 → 0 + 0 0 → 0 Conserved
This contributed to the search for and discovery of the neutrino.
Number Reminders
There may be a clue to the charge of a particle; π+, K+ and e+ have a positive charge.
It will only have a baryon number if it IS a baryon. Mesons and Leptons have a Baryon Number of zero.
It will only have a lepton number if it IS a lepton. Baryons and Mesons have a Lepton Number of zero.
It will only have a strangeness if it is made from a strange quark. Leptons have a strangeness of zero.
 Unit 1
Lesson 6
Forces and Exchange Particles
To know the four fundamental forces, their ranges and relative strengths
Learning
Outcomes To know what each force does and what it acts on
To be able to explain what exchange particles are N. DWYER

The Four Interactions

There are four forces in the universe, some you will have come across already and some will be new:
The electromagnetic interaction causes an attractive or repulsive force between charges.
The gravitational interaction causes an attractive force between masses.
The strong nuclear interaction causes an attractive (or repulsive) force between quarks (and so
hadrons).
The weak nuclear interaction does not cause a physical force, it makes particles decay. ‘Weak’ means there is a
low Interaction/Force
probability that it will happen.Range Relative Strength
Strong Nuclear ~10 m
-15
1 (1)
Electromagnetic ∞ ~10–2 (0.01)
Weak Nuclear ~10-18m ~10–7 (0.0000001)
–36
Gravitational ~10 (0.000000000000000000000000000000000001)
∞

Exchange Particles
In 1935 Japanese physicist Hideki Yukawa put forward the idea that the interactions/forces between two
particles were caused by ‘virtual particles’ being exchanged between the two particles.
He was working on the strong nuclear force which keeps protons and neutrons together and theorised that they
were exchanging a particle back and forth that ‘carried’ the force and kept them together. This is true of all the
fundamental interactions.
The general term for exchange particles is bosons and they are fundamental particles like quarks and leptons.
Ice Skating Analogy
Imagine two people on ice skates that will represent the two bodies experiencing a force.
If A throws a bowling ball to B, A slides back when they release it and B moves back when they catch it.
Repeatedly throwing the ball back and forth moves A and B away from each other, the force causes repulsion.
The analogy falls a little short when thinking of attraction, but bear with it.
Now imagine that A and B are exchanging a boomerang (bear with it), throwing it behind them pushes A
towards B, B catches it from behind and moves towards A. The force causes attraction.

Which Particle for What Force

Each of the interactions/forces has its own exchange particles.
Interaction/Force Exchange Particle What is acts upon
Strong Nuclear Gluons between quarks Pions between Baryons Nucleons (Hadrons)
Electromagnetic Virtual Photon Charged particles
Weak Nuclear W+ W– Z0 All particles
Gravitational Graviton Particles with masses

Borrowing Energy to Make Particles

The exchange particles are made from ‘borrowed’ energy, borrowed from where? From nowhere! Yukawa used
the Heisenberg Uncertainty Principle to establish that a particle of mass-energy ΔE could exist for a time Δt as
long as E.t  where h is Planck’s constant. This means that a heavy particle can only exist for a short time
h
while a lighter particle may exist for longer.
h is Planck’s Constant, h = 6.63 x 10-34 J s.
In 1947 the exchange particle of the strong nuclear interaction were observed in a cloud chamber.
Lending Money Analogy
Think of making exchange particles in terms of lending somebody some money.
If you lend somebody £50 you would want it paid back fairly soon.
If you lend somebody 50p you would let them have it for longer before paying
you back.
 Unit 1
Lesson 7
The Strong Interaction
To know why a nucleus doesn’t tear itself apart
Learning
Outcomes To know why a nucleus doesn’t collapse in on itself
To know why the neutron exists in the nucleus N. DWYER

The Strong Interaction

The strong nuclear force acts between quarks. Since Hadrons are the only particles made of
quarks only they experience the strong nuclear force.
In both Baryons and Mesons the quarks are attracted to each other by exchanging virtual
particles called ‘gluons’.

On a larger scale the strong nuclear force acts between the Hadrons
themselves, keeping them together. A pi-meson or pion (π) is exchanged
between the hadrons. This is called the residual strong nuclear force.

Force Graphs
Neutron-Neutron or Neutron-Proton
Here is the graph of how the force varies between two neutrons or a proton
and a neutron as the distance between them is increased.
We can see that the force is very strongly repulsive at separations of less
than 0.7 fm ( x 10–15 m). This prevents all the nucleons from crushing into
each other.
Above this separation the force is strongly attractive with a peak around 1.3
fm. When the nucleons are separated by more than 5 fm they no longer
experience the SNF.
Proton-Proton
The force-separation graphs for two protons is different. They both attract each other due to the SNF but they
also repel each other due to the electromagnetic force which causes two like charges to repel.

Graph A Graph B Graph C Graph A shows how the strong nuclear force
varies with the separation of the protons
Graph B shows how the electromagnetic force varies with the separation of the protons
Graph C shows the resultant of these two forces: repulsive at separations less than 0.7 fm, attractive
up to 2 fm when the force becomes repulsive again.

Neutrons – Nuclear Cement

In the lighter elements the number of protons and neutrons in the nucleus is the same. As the
nucleus gets bigger more neutrons are needed to keep it together.

Adding another proton

means that all the other nucleons feel
the SNF attraction. It also means that
all the other protons feel the EM
repulsion.

Adding another neutron

adds to the SNF attraction between
the nucleons but, since it is
uncharged, it does not contribute to
the EM repulsion.
 Unit 1
Lesson 8
The Weak Interaction
To be able to write the equation for alpha and beta decay
Learning
Outcomes To know what a neutrino is and why is must exist
To be able to state the changes in quarks during beta plus and beta minus decay N. DWYER

Alpha Decay
When a nucleus decays in this way an alpha particle (a helium nucleus) is ejected from the nucleus.
Z
A
X  ZA42 Y 24 or Z X  ZY
A A4
2  He
4
2

All the emitted alpha particles travelled at the same speed, meaning they had the same amount of energy. The
law of conservation of mass-energy is met, the energy of the nucleus before the decay is the same as the
energy of the nucleus and alpha particle after the decay.
Alpha decay is NOT due to the weak interaction but Beta decay IS

Beta Decay and the Neutrino

In beta decay a neutron in the nucleus changes to a proton and releases a beta particle (an electron).
The problem with beta decay was that the electrons had a range of energies so the law of conservation of mass-
energy is violated, energy disappears. There must be another particle being made with zero mass but variable
speeds, the neutrino.
We can also see from the particle conservation laws that this is a forbidden interaction: n  p  e
Charge Q: 0 +1–1 00 Charge is conserved
Baryon Number B: +1  +1+0 11 Baryon number is conserved
Lepton Number L: 0  0+1 01 Lepton number is NOT conserved
Beta Minus (β–)
In neutron rich nuclei a neutron may decay into a proton, electron and an anti electron neutrino.
Decay
n  p  e 
e
Charge Q: 0 +1–1+0 00 Charge is conserved
Baryon Number B: +1  11 Baryon number is conserved
+1+0+0
Lepton Number L: 0  0+1–1 00 Lepton number is conserved

In terms of quarks beta minus decay looks like this: dud  uud  e  which simplifies
to:
e
d  u  e 
e
Charge Q: – ⅓ +⅔–1+0 – ⅓ – ⅓ Charge is conserved
Baryon Number B: +⅓ +⅓+0+0 ⅓ ⅓ Baryon number is conserved
Lepton Number L: 0  0+1–1 00 Lepton number is conserved
Beta Plus (β+) Decay
In proton rich nuclei a proton may decay into a neutron, positron and an electron neutrino.
p  n  e 
e
Charge Q: +1  0+1+0 11 Charge is conserved
Baryon Number B: +1  11 Baryon number is conserved
+1+0+0
Lepton Number L: 0  0–1+1 00 Lepton number is conserved

In terms of quarks beta plus decay looks like this: uud  dud  e  which simplifies to:
e
u  d  e  
e
Charge Q: +⅔ –⅓+1+0 ⅔ ⅔ Charge is conserved
Baryon Number B: +⅓ +⅓+0+0 ⅓ ⅓ Baryon number is conserved
StrangenessLepton Number L: 0  0–1+1 00 Lepton number is conserved
The weak interaction is the only interaction that causes a quark to change into a different type of quark. In beta
decay up quarks and down quarks are changed into one another. In some reactions an up or down quark can
change into a strange quark meaning strangeness is not conserved.
During the weak interaction there can be a change in strangeness of ±1.
 Unit 1
Lesson 9
Feynman Diagrams
To know what a Feynman diagram shows us
Learning
Outcomes To be able to draw Feynman diagrams to represent interactions and decays
To be able to state the correct exchange particle N. DWYER

Feynman Diagrams
An American Physicist called Richard Feynman came up with a way of visualising forces and exchange particles.
Below are some examples of how Feynman diagrams can represent particle interactions.
The most important things to note when dealing with Feynman diagrams are the arrows and the exchange
particles, the lines do not show us the path that the particles take only which come in and which go out.
The arrows tell us which particles are present before the interaction and which are present after the interaction.
The wave represents the interaction taking place with the appropriate exchange particle labelled.
Examples

Diagram 1 represents the strong interaction. A proton and neutron are attracted together by the exchange of a
neutral pion.
Diagram 2 represents the electromagnetic interaction. Two electrons repel each other by the exchange of a
virtual photon.
Diagram 3 represents beta minus decay. A neutron decays due to the weak interaction into a proton, an
electron and an anti electron neutrino
Diagram 4 represents beta plus decay. A proton decays into a neutron, a positron and an electron
neutrino.

Diagram 5 represents electron capture. A proton captures an electron and becomes a neutron and an electron
neutrino.
Diagram 6 represents a neutrino-neutron collision. A neutron absorbs a neutrino and forms a proton and an
electron.
Diagram 7 represents an antineutrino-proton collision. A proton absorbs an antineutrino and emits a neutron
and an electron.
Diagram 8 represents an electron-proton collision. They collide and emit a neutron and an electron neutrino.
Getting the Exchange Particle
The aspect of Feynman diagrams that students often struggle with is labelling the exchange particle and the
direction to draw it. Look at what you start with:
If it is positive and becomes neutral you can think of it as throwing away its positive charge so the boson will be
positive. This is the case in electron capture.
If it is positive and becomes neutral you can think of it as gaining negative to neutralise it so the boson will be
negative. This is the case in electron-proton collisions.
If it is neutral and becomes positive we can think of it either as gaining positive (W+ boson) or losing negative
(W– boson in the opposite direction).
Work out where the charge is going and label it.
 Unit 1
Lesson 10
The Photoelectric Effect
To know what the photoelectric effect is and how frequency and intensity affect it
Learning
Outcomes To be able to explain what photon, photoelectron, work function and threshold frequency are
To be able to calculate the kinetic energy of a photoelectron N. DWYER

Observations
When light fell onto a metal plate it released electrons from the surface straight away. Increasing the intensity
increased the number of electrons emitted. If the frequency of the light was lowered, no electrons were
emitted at all. Increasing the intensity and giving it more time did nothing, no electrons were emitted.
If Light was a Wave…
Increasing the intensity would increase the energy of the light. The energy from the light would be evenly
spread over the metal and each electron would be given a small amount of energy. Eventually the electron
would have enough energy to be removed from the metal.
Photon
Max Planck had the idea that light could be released in ‘chunks’ or packets of energy. Einstein named these
wave-packets photons. The energy carried by a photon is given by the equation:

E  hf Since c  f we can also write this as: E  

hc

Explaining the Photoelectric Effect

Einstein suggested that one photon collides with one electron in the metal, giving it enough energy to be
removed from the metal and then fly off somewhere. Some of the energy of the photon is used to break the
bonds holding the electron in the metal and the rest of the energy is used by the electron to move away (kinetic
energy). He represented this with the equation: hf   
hf represents the energy of the photon, EisK the work function and EK is the kinetic energy.
Work Function, 
The work function is the amount of energy the electron requires to be completely removed from the surface of
the metal. This is the energy just to remove it, not to move away.
Threshold Frequency, f0
The threshold frequency is the minimum frequency that would release an electron from the surface of a metal,
any less and nothing will happen.
Since hf    EK , the minimum frequency releases an electron that is not moving, so EK = 0


hf0   which can be rearranged to give: f0 
h light sources gives out each second.
Increasing the intensity increases the number of photons the
If the photon has less energy than the work function an electron can not be removed. Increasing the intensity
just sends out more photons, all of which would still not have enough energy to release an electron.
Graph
If we plot a graph of the kinetic energy of the electrons against frequency
we get a graph that looks like this:
Start with hf    EK and transform into y  mx  c
EK is the y-axis and f is the x- axis. .
This makes the equation become: EK  hf 
So the gradient represents
and the y-intercept
Planck’s constant represents (–) the work function.
Nightclub Analogy
We can think of the photoelectric effect in terms of a full nightclub; let the people going into the club represent
the photons, the people leaving the club represent the electrons and money represent the energy.
The club is full so it is one in and one out. The work function equals the entrance fee and is £5:
If you have £3 you don’t have enough to get in so noone is kicked out.
If 50 people arrive with £3 no one has enough, so one gets in and noone is kicked out.
If you have £5 you have enough to get in so someone is kicked out, but you have no money for booze.
If 50 people arrive with £5 you all get in so 50 people are kicked out, but you have no money for booze.
If you have £20 you have enough to get in so someone is kicked out and you have £15 to spend on
booze.
If 50 people arrive with £20 you all get in so 50 people are kicked out and you have £15 each to spend
 Unit 1
Lesson 11
Excitation, Ionisation and Energy Levels
To know how Bohr solved the falling electron problem
Learning
Outcomes To be able to explain what excitation, de-excitation and ionisation are
To be able to calculate the frequency needed for excitation to a certain level N. DWYER

The Electronvolt, eV
The Joule is too big use on an atomic and nuclear scale so we will now use the electronvolt, represented by eV.
One electronvolt is equal to the energy gained by an electron of charge e, when it is accelerated through a
potential difference of 1 volt. 1eV = 1.6 x 10-19J 1J = 6.25 x 1018eV
eV  J multiply by e J  eV divide by e
The Problem with Atoms
Rutherford’s nuclear model of the atom leaves us with a problem: a
charged particle emits radiation when it accelerates. This would
mean that the electrons would fall into the nucleus.
Bohr to the Rescue
Niels Bohr solved this problem by suggesting that the electrons could
only orbit the nucleus in certain ‘allowed’ energy levels. He
suggested that an electron may only transfer energy when it moves
from one energy level to another. A change from one level to
another is called a ‘transition’.
To move up and energy level the electron must gain the
exact amount of energy to make the transition.
It can do this by another electron colliding with it or
by absorbing a photon of the exact energy.
When moving down a level the electron must lose the
exact amount of energy when making the transition.
It releases this energy as a photon of energy
equal
to the energyE it loses.
 hf  E 
1

E2 level the electron starts at and E2 is

E1 is the energy of the
the energy of the level the electron ends at
Excitation
When an electron gains the exact amount of energy to
move up one or more energy levels
De-excitation
When an electron gives out the exact amount of energy
to move back down to its original energy level
Ionisation
An electron can gain enough energy to be completely
removed from the atom.
The ground state and the energy levels leading up to ionisation have negative values of energy, this is because
they are compared to the ionisation level. Remember that energy must be given to the electrons to move up a
level and is lost (or given out) when it moves down a level.
Line Spectra
Atoms of the same element have same energy levels. Each
transition releases a photon with a set amount of energy meaning
the frequency and wavelength are also set. The wavelength of
light is responsible for colour it is. We can analyse the light by
using a diffraction grating to separate light into the colours that
makes it up, called its line spectra. Each
element has its own line spectra like a
barcode.
To the above right are the line spectra of Hydrogen and Helium.
We can calculate the energy difference that created the colour.
If we know the energy differences for each element we can work out which element
is responsible for the light and hence deduce which elements are present.
We can see that there are 6 possible transitions in the diagram to the left, A to F.
 Unit 1
Lesson 12
Wave-Particle Duality
To know how to calculate the de Broglie wavelength and what is it
Learning
Outcomes To be able to explain what electron diffraction shows us
To know what wave-particle duality is N. DWYER

De Broglie
In 1923 Louis de Broglie put forward the idea that ‘all particles have a wave nature’ meaning that particles can
behave like waves.
This doesn’t sound too far fetched after Einstein proved that a wave can behave like a particle.
De Broglie said that all particles could have a wavelength. A particle of mass, m, that is travelling at velocity, v,
would have a wavelength given by:
h
 which is sometime written as   h where p is momentum
 mv
p the de Broglie wavelength. The modern view is that the de Broglie wavelength is
This wavelength is called
linked to the probability of finding the particle at a certain point in space.
De Broglie wavelength is measured in
metres, m
Electron Diffraction
Two years after de Broglie came up with his
particle wavelengths and idea that electrons
could diffract, Davisson and Germer proved
this to happen.
They fired electrons into a crystal structure
which acted as a diffraction grating. This
produced areas of electrons and no electrons
on the screen behind it, just like the pattern
you get when light diffracts.
Electron Wavelength
We can calculate the de Broglie wavelength
of an electron from the potential difference, V, that accelerated it.
Change in electric potential energy gained = eV
This is equal to the kinetic energy of the electron eV  1 mv 2
2

The velocity is therefore given by: 2eV

m v
h h
We can substitute this into  to get: 
mv  2me
Sand Analogy V
If we compare a double slit electron diffraction to sand falling from containers we can see how crazy electron
diffraction is. Imagine two holes about 30cm apart that sand is
dropping from. We would expect to find a maximum amount
of sand under each hole, right? This is not what we find! We
find a maximum in between the two holes. The electrons are
acting like a wave.
Wave-Particle Duality
Wave-particle duality means that waves sometimes behave like particles and particles sometimes behave like
waves. Some examples of these are shown below:
Light as a Wave
Diffraction, interference, polarisation and refraction all prove that light is a wave and will be covered in Unit
2.
Light as a Particle
We have seen that the photoelectric effect shows that light can behave as a particle called a photon.
Electron as a Particle
The deflection by an electromagnetic field and collisions with other particles show its particle nature.
Electron as a Wave
Electron diffraction proves that a particle can show wave behaviour.
 Unit 1
Lesson 13
QVIRt
To be able to explain what current, charge, voltage/potential difference and resistance are
Learning
Outcomes To know the equations that link these
To know the correct units to be use in each N. DWYER

Definitions (Also seen in GCSE Physics 2)

Current, I
Electrical current is the rate of flow of charge in a circuit. Electrons are charged particles that move around the
circuit. So we can think of the electrical current is the rate of the flow of electrons, not so much the speed but
the number of electrons moving in the circuit. If we imagine that electrons are Year 7 students and a wire of a
circuit is a corridor, the current is how many students passing in a set time.
Current is measured in Amperes (or
Amps), A
Charge, Q
The amount of electrical charge is a fundamental unit, similar to mass and length and time. From the data sheet
we can see that the charge on one electron is actually -1.60 x 10-19 C. This means that it takes 6.25 x 1018
electrons to transfer 1C of charge.
Charge is measured in Coulombs,
C
Voltage/Potential Difference, V
Voltage, or potential difference, is the work done per unit charge.
1 unit of charge is 6.25 x 1018 electrons, so we can think of potential difference as the energy given to each of
the electrons, or the pushing force on the electrons. It is the p.d. that causes a current to flow and we can think
of it like water flowing in a pipe. If we make one end higher than the other end, water will flow down in, if we
increase the height (increase the p.d.) we get more flowing. If we think of current as Year 7s walking down a
corridor, the harder we push them down the corridor the more we get flowing.
Voltage and p.d. are measured in Volts,
V
Resistance, R
The resistance of a material tells us how easy or difficult it is to make a current flow through it. If we think of
current as Year 7s walking down a corridor, it would be harder to make the Year 7s flow if we added some Year
11 rugby players into the corridor. Increasing resistance lowers the current.
Resistance is measured in Ohms,
Ω
Time, t
You know, time! How long stuff takes and that.
Time is measured in seconds,
s
Equations
There are three equations that we need to be able to explain and substitute numbers into.
1
Q
I
t
This says that the current is the rate of change of charge per second and backs up or idea of current as the rate
at which electrons (and charge) flow.
This can be rearranged into
Q  It
which means that the charge is equal to how much is flowing multiplied by how long it flows for.

2
E
V V IR
Q
This says that increasing the p.d. increases the current. Increasing the ‘push’ of the electrons makes more flow.
This says
It also thatus
shows thethat
voltage/p.d. is equal
for constant V, if Rtoincreases
the energy persmaller.
I gets charge.Pushing
The ‘push’
theof the electrons
same strength, is equal istomore
if there the
energy given to each charge (electron).
blocking force less current will flow.

3
 Unit 1
Lesson 14
Ohm’s Laws and I-V Graphs
To be able to sketch and explain the I-V graphs of a diode, filament lamp and resistor
Learning
Outcomes To be able to describe the experimental set up and measurements required to obtain these graphs
To know how the resistance of an LDR and Thermistor varies N. DWYER

Ohm’s Law (Also seen in GCSE Physics 2)

After the last lesson we knew that a voltage (or potential difference) causes a current to flow and that the size
of the current depends on the size of the p.d.
For something to obey Ohm’s law the current flowing is proportional to the p.d. pushing it. V=IR so this means
the resistance is constant. On a graph of current against p.d. this appears as a straight line.

Taking Measurements
To find how the current through a component varies with
the potential difference across it we must take readings.
To measure the potential difference we use a voltmeter
connected in parallel and to measure the current we use
an ammeter connected in series.
If we connect the component to a battery we would now
have one reading for the p.d. and one for the current. But
what we require is a range of readings. One way around
this would be to use a range of batteries to give different
p.d.s. A better way is to add a variable resistor to the circuit, this allows us to use one battery and get a range of
readings for current and p.d. To obtain values for current in the negative direction we can reverse either the
battery or the component.

I-V Graphs (Also seen in GCSE Physics 2)

Resistor
This shows that when p.d. is zero so is the current. When we increase the p.d. in one
direction the current increases in that direction. If we apply a p.d. in the reverse
direction a current flows in the reverse direction. The straight line shows that current is
proportional to p.d. and it obeys Ohm’s law. Graph a has a lower resistance than graph
b because for the same p.d. less current flows through b.

Filament Lamp
At low values the current is proportional to p.d. and so, obeys Ohm’s law.
As the potential difference and current increase so does the temperature. This
increases the resistance and the graph curves, since resistance changes it no longer
obeys Ohm’s law.

Diode
This shows us that in one direction increasing the p.d. increases the current but in the
reverse direction the p.d. does not make a current flow. We say that it is forward
biased. Since resistance changes it does not obey Ohm’s law.

Three Special Resistors (Also seen in GCSE Physics 2)

Variable Resistor
A variable resistor is a resistor whose value can be changed.

Thermistor
The resistance of a thermistor varied with temperature. At
low temperatures the resistance is high, at high
temperatures the resistance is low.

Light Dependant Resistor (L.D.R)

The resistance of a thermistor varied with light intensity.
In
dim light the resistance is high and in bright light the
resistance is low.
 Unit 1
Lesson 15
Resistivity and Superconductivity
To be able to state what affects resistance of a wire and explain how they affect it
Learning
Outcomes To be able to describe the experimental set up required to calculate resistivity and define it
To be able to explain superconductivity and state its uses N. DWYER

Resistance
The resistance of a wire is caused by free electrons colliding with the positive ions that make up the structure of
the metal. The resistance depends upon several factors:
Length, l Length increases – resistance increases
The longer the piece of wire the more collisions the electrons will have.
Area, A Area increases – resistance decreases
The wider the piece of wire the more gaps there are between the ions.
Temperature Temperature increases – resistance increases As temperature increases the ions are given
more energy and vibrate more, the electrons are more likely to collide with the ions.
Material
The structure of any two metals is similar but not the same, some metal ions are closer together, others have
bigger ions.

Resistivity, ρ
The resistance of a material can be calculate using l where ρ is the resistivity of the
material. R
 A
Resistivity is a factor that accounts for the structure of the metal and the temperature. Each metal has its own
value of resisitivity for each temperature. For example, the resistivity of copper is 1.7x10-8 Ωm and carbon is
3x10-5 Ωm at room temperature. When both are heated to 100°C their resistivities increase.
Resistivity is measured in Ohm metres ,
Ωm

Measuring Resistivity
In order to measure resistivity of a wire we need to measure the
length, cross-sectional area (using Area = πr2) and resistance.
Remember, to measure the resistance we need to measure
values of
current and potential difference using theRA
set up shown on the
We then rearrange the equation to   and substitute values in
right l

Superconductivity
The resistivity (and so resistance) of metals increases with the
temperature. The reverse is also true that, lowering the
temperature lowers the resistivity.
When certain metals are cooled below a critical temperature
their resistivity drops to zero. The metal now has zero
resistance and allows massive currents to flow without losing
any energy as heat. These metals are called superconductors.
When a superconductor is heated above it’s critical
temperature it loses its superconductivity and behaves like
other metals.
The highest recorded temperature to date is –196°C, large
amounts of energy are required to cool the metal to below this
temperature.

Uses of Superconductors
High-power electromagnets
Power cables
Magnetic Resonance
Imaging (MRI) scanners
 Unit 1
Lesson 16
Series and Parallel Circuits
To be able to calculate total current in series and parallel circuits
Learning
Outcomes To be able to calculate total potential difference in series and parallel circuits
To be able to calculate total resistance in series and parallel circuits N. DWYER

Series Circuits (Also seen in GCSE Physics 2)

In a series circuit all the components are in
one circuit or loop. If resistor 1 in the
diagram was removed this would break the
whole circuit.

The total current of the circuit is the same at each ITOTAL  I1  I2  I3

point in the circuit.
The total voltage of the circuit is equal to the sum of the p.d.s across each resistor. The VTOTAL  V1  V2  V3

total resistance of the circuit is equal to the sum of the resistance of each resistor. RTOTAL  R1  R2  R3

Parallel Circuits (Also seen in GCSE Physics 2)

Components in parallel have their own separate circuit or loop. If resistor 1 in
the diagram was removed this would only break that circuit, a current
would still flow through resistors 2 and 3.

The total current is equal to the sum of the currents through each resistor.
ITOTAL  I1  I2  I3
The total potential difference is equal to the p.d.s across each resistor.

VTOTAL  V1  V2 
The total resistance can be calculated using the equation:
V3 1
1   1  1
RTOTAL R1 R2 R3

Water Slide Analogy

Imagine instead of getting a potential difference we get a height difference by reaching
the top of a slide. This series circuit has three connected slides and the parallel circuit
below has three separate slides that reach the bottom.

Voltages/P.D.s
In series we can see that the total height loss is equal to how much you fall on slide 1,
slide 2 and slide 3 added together. This means that the total p.d. lost must be the p.d.
given by the battery. If the resistors have equal values this drop in potential difference
will be equal.
In parallel we see each slide will drop by the same height meaning the potential
difference is equal to the total potential difference of the battery.

Currents
If we imagine 100 people on the water slide, in series we can see that 100
people get to the top. All 100 must go down slide 1 then slide 2 and final
slide 3, there is no other option. So the current in a series circuit is the
same everywhere.
In parallel we see there is a choice in the slide we take. 100 people get to
the top of the slide but some may go down slide 1, some down slide 2 and
some down slide 3. The total number of people is equal to the number of
people going down each slide added together, and the total current is
equal to the currents in each circuit/loop.
 Unit 1
Lesson 17
Energy and Power
To know what power is and how to calculate the power of an electrical circuit
Learning
Outcomes To know how to calculate the energy transferred in an electrical circuit
To be able to derive further equations or use a series of equations to find the answer N. DWYER

Power (Also seen in GCSE Physics 1)

Power is a measure of how quickly something can transfer energy. Power is linked to energy by the equation:
Energy Power is measured in Watts, W
Power 
Energy is measured in Joules, J
time Time is measured in seconds, s
New Equations
If we look at the equations from the QVIRt lesson we can derive some new equations for energy and power.
Energy
E
V can be rearranged into E  VQ and we know that Q  It so combining these equations we get a
new Q
one to calculate the energy in an electric circuit:
E  VQ <---------------------- Q  It so E  (1)
VIt
Power
If we look at the top equation, to work out power we divide energy by time:
E VIt which cancels out to become P (2)
t  t VI
If we substituteV  IR into the last equation we get another equation for
power:
P  IV <---------------------- V  so P  I 2 (3)
IR R
V
We can also rearrange V  IR into I R and substitute this into P  VI to get our last equation for
power:
V V 2 (4)
P  VI <---------------------- I so P
 R
R

Energy again
Two more equations for energy can be derived from the equation at the top and equations 3 and 4
Energy = Power x time

Pt  I 2 Rt Equation 3 E  I 2 Rt (5)
becomes
2 2
Pt V t Equation 4 becomes E V t (6)
R R

Fuses (Also seen in GCSE Physics 2)

Electrical devices connected to the Mains supply by a three-pin plug have a fuse as part of their circuit. This is
a thin piece of wire that melts if the current through it exceeds its maximum tolerance. The common fuses
used are 3A, 5A and 13A. A 100W light bulb connected to the UK Mains would have a 240V potential difference
across it. Using P  IV we can see that the current would be 0.42A so a 2A fuse would be the best to use.

Applications
The starter motor of a motor car needs to transfer a lot of energy very quickly, meaning its needs a high power.
Millions of Joules are required in seconds; since the voltage of the battery is unchanging we need current in the
region of 160A which is enormous.
The power lines that are held by pylons and form part of the National Grid are very thick and carry electricity
that has a very high voltage. Increasing the voltage lowers the current so if we look at the equation
E  I 2 Rt we can see that this lowers the energy transferred to the surroundings.
 Unit 1
Lesson 18
EMF and Internal Resistance
To know what emf and internal resistance are
Learning
Outcomes To know how to measure internal resistance
To be able sketch and interpret a V-I graph, labelling the gradient and y-intercept N. DWYER

Energy in Circuits
In circuits there are two fundamental types of component: energy givers and energy takers.
Electromotive Force (emf), ε
Energy givers provide an electromotive force, they force electrons around the circuit which transfer energy.

The size of the emf can be calculate using:   QE

This is similar to the equation we use to find voltage/potential difference and means the energy given to each
unit of charge. We can think of this as the energy given to each electron.
The emf of a supply is the p.d. across its terminals when no current flows
EMF is measured in Joules per Coulomb, JC-1 or
Volts, V

Energy takers have a potential difference across them, transferring energy from the circuit to the component.
emf = energy giver p.d. = energy taker
Energy is conserved in a circuit so energy in = energy out, or:
The total of the emfs = The total of the potential differences around the whole
circuit
Internal Resistance, r
The chemicals inside a cell offer a resistance to the flow of current, this is the internal resistance on the cell.
Internal Resistance is measured in Ohms, Ω
Linking emf and r
If we look at the statement in the box above and apply it to the circuit below, we can reach an equation that
links emf and r.
Total emfs = total potential differences
ε = (p.d. across r) + (p.d. across R) {Remember that V=IR}
ε = (I x r) + (I x R)
ε = Ir + IR
ε = I(r+R)
The terminal p.d. is the p.d. across the terminals of the cell when a current is
flowing
ε = internal p.d + terminal p.d.
So the above equation can be written as ε = Ir + V where V is the terminal p.d.

Measuring emf and r

We can measure the emf and internal resistance of a cell by measuring the
current and voltage as shown on the right, the variable resistor allows us to get
a range of values. If we plot the results onto a graph of voltmeter reading
against ammeter reading we get a graph that looks like the one below.

Graphs have the general equation of y = mx+c, where y is the vertical (upwards)
axis, x is the horizontal (across) axis, m is the gradient of the line and c is where
the line intercepts (cuts) the y axis.
If we take ε = Ir + V and arrange it into y= mx + c
y axis = V and x axis = I
ε = Ir + V  V = -Ir + ε  V = -r I + ε
y =m x +c
So we can see that the:
y-intercept represents the emf
and
gradient represents (–)internal resistance
 Unit 1
Lesson 19
Kirchhoff and Potential Dividers
To know Kirchhoff’s laws and be able to apply them to questions
Learning
Outcomes To know what a potential dividers is and be able to calculate the output voltage
To be able to explain an application of a potential divider N. DWYER

Kirchhoff’s Laws
Kirchhoff came up with two (some may say rather obvious) laws concerning
conservation in electrical circuits.

Captain Obvious’ First Law

Electric charge is conserved in all circuits, all the charge that arrives at a point
must leave it.
Current going in = current going out.
In the diagram we can say that: I1 = I 2 + I3 + I4

Captain Obvious’ Second Law

Energy is conserved in all circuits, for any complete circuit the sum of the emfs is
equal to the sum of the potential differences.
Energy givers = energy takers.
In the diagram we can say that: ε = pd1 + pd2 + pd3 +
pd4.

Potential Dividers
A potential divider is used to produce a desired potential difference, it can
be thought of as a potential selector.
A typical potential divider consists of two or more resistors that share the
emf from the battery/cell.
The p.d.s across R1 and R2 can be calculated using the following
equations:
R1 R2
V1  V2 
V
0
R1  2 V
0
R1  2
R R
This actually shows us that the size of the potential difference is equal to the input potential multiplied by what
proportion of R1 is of the total resistance.
If R1 is 10 Ω and R2 is 90 Ω, R1 contributes a tenth of the total resistance so R1 has a tenth of the available
potential. This can be represented using:
R1 V1
The ratio of the resistances is equal to the ratio of the output voltages.
R2 V2
Uses
In this potential divider the second resistor is a thermistor. When the
temperature is low the resistance (R2) is high, this makes the output voltage
high. When the temperature is high the resistance (R2) is low, this makes the
output voltage low. A use of this would be a cooling fan that works harder
when it is warm.

In the second potential divider the second resistor is a Light Dependant Resisitor.
When the light levels are low the resistance (R2) is high, making the output voltage
high. When the light levels increase the resistance (R2) decreases, this makes the
output voltage decrease. A use of this could be a street light sensor that lights up
when the surrounding are dark.
 Unit 1
Lesson 20
Alternating Current
To know what peak current/voltage is and to be able to identify it
Learning
Outcomes To know what peak-to-peak current/voltage is and to be able to identify it
To know what r.m.s. values are and to be able to calculate them N. DWYER

ACDC Definitions (Also seen in GCSE Physics 2)

Direct Current
Cells and batteries are suppliers of direct current; they supply an emf in one direction.
In the graph below we can see that the current and voltage are constant. The bottom line shows that when the
battery or cell is reversed the voltage and current are constants in the other direction
Alternating Current
The Mains electricity supplies an alternating current; it supplies an emf that alternates from maximum in one
direction to maximum in the other direction.
In the graph below we see the voltage and current start at zero, increase to a maximum in the positive
direction, then fall to zero, reach a maximum in the negative direction and return to zero. This is one cycle.

Alternating Current Definitions

Peak Value
The peak value of either the current or
the potential difference is the maximum
in either direction. It can be measured
from the wave as the amplitude, the
distance from 0 to the top (or bottom) of
the wave. We denote peak current with I0
and peak p.d. with V0.
Peak-to-Peak Value
The peak-to-peak value of either the
current or potential difference is the
range of the values. This is literally the
distance from the peak above the zero
line to the peak below the line.
Time Period
In an a.c. current or p.d. this is the
time taken for one complete cycle (or
wave).
Frequency
As with its use at GCSE, frequency is a
measure of how many complete
cycles that occur per second.
F
I0 r
Irms  which can be rearranged to give e 2
2 I0  Irms
q
u
Vrms  V0 e 2
which can also be rearranged to give
n V0  Vrms
2 c
y
 Unit 1
Lesson 21
The Oscilloscope
To know what are the main controls of the oscilloscope
Learning
Outcomes To be able to determine the voltage and current using an oscilloscope
To be able to determine the time period and frequency using an oscilloscope N. DWYER

The Oscilloscope
An oscilloscope can
be used to show the
sizes of voltages and
currents in both d.c.
and a.c. circuits. This
is what a typical
oscilloscope looks
like. A trace would
be seen on the grid
display.

D.C. Traces (Also seen in GCSE Physics 2)

If we connected a battery or cell to an oscilloscope, we would see a trace similar to the
one shown here. The current of a d.c. supply is constant, this means the voltage is
constant.
We see a straight line.

A.C. Traces (Also seen in GCSE Physics 2)

If we connect anything that draws power from the Mains to an oscilloscope we will see a
similar trace to the one shown here. The current is constantly changing from maximum
flow in one direction to maximum flow in the other direction; this means the voltage is
doing the same.
We see a wave.
Controls
There are two main controls that we use are the volts/div and time base dials:
The volts/div (volts per division) dial allows you to change how much each vertical square is worth.
The time base dial allows you to change how much each horizontal square is worth.

Voltage
We can measure the voltage of a d.c. supply by counting the number or vertical squares from the origin to the
line and then multiplying it by the volts/div. In the trace the line is 2.5 squares above 0, if each square is worth 5
volts the voltage is (2.5 x 5) 12.5 volts.
We can measure the peak voltage of an a.c. supply by counting how many vertical squares from the centre of
the wave to the top and then multiplying it by the volts/div (how much voltage each square is worth). In the
trace the peak voltage is 4 squares high, if each square is worth 5 volts the voltage is (4 x 5) 20 volts.

Time and Frequency

We can measure the time for one period (wave) by counting how many horizontal squares one wavelength is
and then multiplying it by the time base (how much time each square is worth).
In the trace above one wave is 6 squares long, if each square is worth 0.02 seconds the time for one wave is
0.12 seconds.
We can calculate the frequency (how many waves or many times this happens per second) using the
equation:
1
f T and T 
1 isf 8.33Hz
If the time period is 0.12 seconds, the frequency
Frequency is measured in Hertz, Hz
 Unit 2
Lesson 1
Scalars and Vectors
To know the difference between scalars and vectors and be able to list some examples of each
Learning
Outcomes To be able to add vectors by scale drawing
To be able to add negative vectors by scale drawing N. DWYER

What is a Vector?
A vector is a physical quantity that has both magnitude (size) and direction.
Examples of Vectors: Displacement, velocity, force, acceleration and momentum.
What is a Scalar?
A scalar is a physical quantity that has magnitude only (it doesn’t act in a certain direction).
Examples of Scalars: Distance, speed, energy, power, pressure, temperature and mass.

Vector Diagrams
A vector can be represented by a vector diagram as well as numerically:
The length of the line represents the magnitude of the vector.
The direction of the line represents the direction of the vector.
We can see that vector a has a greater magnitude than vector b but acts in a different
direction.
A negative vector means a vector of equal magnitude but opposite direction.

Adding Vectors
We can add vectors together to find the affect that two or more would have if acting at the same time. This is
called the resultant vector. We can find the resultant vector in four ways: Scale drawing, Pythagoras, the Sine
and Cosine rules and Resolving vectors (next lesson).

Scale Drawing
To find the resultant vector of a + b we draw vector a then
draw vector b from the end of a. The resultant is the line
that connects the start and finish points.
The resultants of a + b, b – a, a – b, – a – b and would look
like this:

If the vectors were drawn to scale we can find the resultant

by measuring the length of the line and the angle.

Pythagoras
If two vectors are perpendicular to each other the resultant
can be found using Pythagoras:
Vector z is the resultant of vectors x and y.
Since x and y are perpendicular z 2  x 2  y 2  z
x y
2 2

We2 can also use this in 2reverse to find x or y: 2

z  x2   z  y2  x2  z  y2 
y2 x
z 2  x2 
z x  
2
z x y
2 2 2 2
 y
y
Sine and Cosine Rules
2

The sine rule relates the angles and lengths using this equation:
sin A sin B sin C
 
a b c
The Cosine rule relates them using
these equations:
a 2  b 2  c 2  2bc cos
A b 2  a 2  c 2  2ac
cos B c 2  a 2  b 2 
 Unit 2
Lesson 2
Resolving Vectors
To be able to resolve vectors into their vertical and horizontal components
Learning
Outcomes To be able to add vectors and find the resultant by resolving them
To know what equilibrium is and how it is achieved N. DWYER

In the last lesson we looked at how we could add vectors together and find the resultant. In this lesson we will
first look at ‘breaking down’ the vectors and then finding the equilibrium.
Resolving Vectors
A vector can be ‘broken down’ or resolved into its vertical and horizontal components.

We can see that this vector can be resolved into two

perpendicular components, in this case two to the right and
three up.
This is obvious when it is drawn on graph paper but
becomes trickier when there isn’t a grid and still requires an
element of scale drawing.

We can calculate the vertical and horizontal components if we know the magnitude and direction of the vector.
In other words; we can work out the across and upwards bits of the vector if we know the length of the line and
the angle between it and the horizontal or vertical axis.

Adding Resolved Vectors

Now that we can resolve vectors into the vertical and horizontal components it is made from we can add them
together. Look at this example of multiple vectors acting (A).

A B C D
E
If we resolve the vector c we get (B). We can now find the resultant of the horizontal components and the resultant
of the vertical components (C). We can then add these together to find the resultant vector (D) and the angle can
be found using trigonometry (E)

Equilibrium
When all the forces acting on a body cancel out equilibrium is reached and the
object does not move. As you sit and read this the downwards forces acting on
you are equally balanced by the upwards forces, the resultant it that you do
not move.
With scale drawing we can draw the vectors, one after the other. If we end up
in the same position we started at then equilibrium is achieved.
With resolving vectors we can resolve all vectors into their vertical and
horizontal components. If the components up and down are equal and the
components left and right are equal equilibrium has been reached.
 Unit 2
Lesson 3
Moments
To be able to calculate the moment of a single and a pair of forces
Learning
Outcomes To be able to explain what the centre of mass and gravity are
To be able to explain how something balances and becomes stable N. DWYER

Moments (Also seen in GCSE Physics 3)

The moment of a force is its turning affect about a fixed point (pivot).
The magnitude of the moment is given by:
moment = force x perpendicular distance from force to the pivot
moment  Fs

In this diagram we can see that the force is not acting perpendicularly to the pivot.
We must find the perpendicular or closest distance, this is s cosθ.
The moment in this case is given as: moment  Fs
cos
We could have also used the value of s but multiplied it by the vertical component of
the force. This would give us the same equation. moment  F cos.s

Moments are measured in Newton metres, Nm

Couples
A couple is a pair of equal forces acting in opposite directions. If a couple acts on an object it
rotates in position. The moment of a couple is called the torque.
The torque is calculated as: torque = force x perpendicular distance
between forces
torque  Fs
In the diagram to the right we need to calculate the perpendicular
distance, s cosθ.
So in this case: torque  Fs cos

Torque is measured in Newton metres, Nm

Centre of Mass (Also seen in GCSE Physics 3)
If we look at the ruler to the right, every part of it has a mass. To make tackling
questions easier we can assume that all the mass is concentrated in a single point.
Centre of Gravity
The centre of gravity of an object is the point where all the weight of the object appears
to act. It is in the same position as the centre of mass.
We can represent the weight of an object as a downward arrow acting from the centre
of mass or gravity. This can also be called the line of action of the weight.

Balancing (Also seen in GCSE Physics 3)

When an object is balanced:
the total moments acting clockwise = the total moments acting
anticlockwise
An object suspended from a point (e.g. a pin) will come to rest with the centre of mass directly below the point
of suspension.
If the seesaw to the left is balanced then the clockwise moments must be equal to the anticlockwise moments.
Clockwise moment due to 3 and 4
moment  F3 s3  F4 s4
Anticlockwise moments due to 1 and 2
moment  F1s1  F2 s2
So F3 s3  F4 s4  F1s1  F2
Stability (Also seen in GCSE Physics 3) s2
The stability of an object can be increased by lowering the centre of mass and by widening the base.
An object will topple over if the line of action of the weight falls outside of the base.
 Unit 2
Lesson 4
Velocity and Acceleration
To be able to calculate distance and displacement and explain what they are
Learning
Outcomes To be able to calculate speed and velocity and explain what they are
To be able to calculate acceleration and explain uniform and non-uniform cases N. DWYER

Distance (Also seen in Physics 2) Displacement (Also seen in Physics 2)

Distance is a scalar quantity. It is a measure of Displacement is a vector quantity. It is a measure
the total length you have moved. of how far you are from the starting position.

distance travelled = 400m

If you complete a lap of an athletics track:
displacement = 0
Distance and
Displacemen
t are
Speed (Also seen in Physics 2) Velocity (Also seen in Physics 2)
measured in
Speed is a measure of how the distance changes Velocity is measure of how the displacement
metres, m
with time. Since it is dependent on speed it too is changes with time. Since it depends on
a scalar. displacement it is a vector too.

d s
speed  t v  t
Speed and Velocity are is measured in metres per second, m/s
Time is measured in seconds, s
Acceleration (Also seen in Physics 2)
Acceleration is the rate at which the velocity changes. Since velocity is a vector quantity, so is acceleration.
With all vectors, the direction is important. In questions we decide which direction is positive (e.g.  +ve)
If a moving object has a positive velocity: * a positive acceleration means an increase in the velocity
* a negative acceleration means a decrease in the velocity
(it begins the ‘speed up’ in the other direction)
If a moving object has a negative velocity: * a positive acceleration means an increase in the velocity
(it begins the ‘speed up’ in the other direction)
* a negative acceleration means a increase in the velocity
If an object accelerates from a velocity of u to a velocity of v, and it takes t seconds to do it then we can
write (v  u)
a
the equations as v
t it may also look like this a  t where Δ means the ‘change in’

Acceleration is measured in metres per second squared, m/s2

Uniform Acceleration
In this situation the acceleration is constant – the velocity changes by the same amount each unit of time.
For example: If acceleration is 2m/s2, this means the velocity increases by 2m/s every second.
Time (s) 0 1 2 3 4 5 6 7
Velocity (m/s) 0 2 4 6 8 10 12 14
Acceleration (m/s2) 2 2 2 2 2 2 2
Non-Uniform Acceleration
In this situation the acceleration is changing – the velocity changes by a different amount each unit of time.
For example:
Time (s) 0 1 2 3 4 5 6 7
Velocity (m/s) 0 2 6 10 18 28 30 44
Acceleration (m/s2) 2 4 6 8 10 12 14
 Unit 2
Lesson 5
Motion Graphs
To be able to interpret displacement-time and velocity-time graphs
Learning
Outcomes To be able to represent motion with displacement-time and velocity-time graphs
To know the significance of the gradient of a line and the area under it N. DWYER

Before we look at the two types of graphs we use to represent motion, we must make sure we know how to
calculate the gradient of a line and the area under it.
Gradient
We calculate the gradient by choosing two points on the line and calculating the change in the y axis (up/down)
and the change in the x axis (across).
y
gradient  x
Area Under Graph
At this level we will not be asked to calculate the area under curves, only straight lines.
We do this be breaking the area into rectangles (base x height) and triangles (½ base x height).
Displacement-Time Graphs (Also seen in GCSE Physics 2)

A B C
Graph A shows that the displacement stays at 3m, it is stationary.
Graph B shows that the displacement increases by the same amount each second, it is travelling with constant
velocity.
Graph C shows that the displacement covered each second increases each second, it is accelerating.
y s
Since gradient  and y = displacement and x = time  gradient   gradient 
x velocity
t
Velocity- Time Graphs (Also seen in GCSE Physics 2)

A B C
Graph A shows that the velocity stays at 4m/s, it is moving with constant velocity.
Graph B shows that the velocity increases by the same amount each second, it is accelerating by the same
amount each second (uniform acceleration).
Graph C shows that the velocity increases by a larger amount each second, the acceleration is increasing (non-
uniform acceleration).
y v
Since gradient  and y = velocity and x = time  gradient   gradient  accelerati
x on
area = displacement
t
area = base x height  area = time x velocity  show the velocity decreasing in one direction and increasing in
This graph
the opposite direction.
If we decide that is negative and is positive then the graph tells us:
The object is initially travels at 5 m/s 
It slows down by 1m/s every second
After 5 seconds the object has stopped
It then begins to move 
It gains 1m/s every second until it is
travelling at 5m/s 
 Unit 2
Lesson 6
Equations of Motion
To be able to use the four equations of motion
Learning
Outcomes To know the correct units to be used
To be able to find the missing variable:, s u v a or t N. DWYER

Defining Symbols
Before we look at the equations we need to assign letters to represent each variable
Displacement =s m metres
Initial Velocity =u m/s metres per second
Final Velocity =v m/s metres per second
Acceleration =a m/s 2
metres per second per second
Time =t s seconds

Equations of Motion
Equation 1
(v  u)
If we start with the equation for acceleration a we can rearrange this to give us an equation 1
 t
vu
at  (v  u)  at  u  v at
Equation 2
We start with the definition of velocity and rearrange for displacement
velocity = displacement / time  displacement = velocity x time

In situations like the graph to the right the velocity is constantly changing, we
need to use the average velocity.
displacement = average velocity x time
(u 
The average velocity is give by: average velocity =
v) 2
We now substitute this into the equation above for displacement
(u  v)
s  21 (u 
(u  v) v)t
displacement = x time  s  t
Equation 3 2
With Equations 1 and 2 we can derive an equation which eliminated v. To do this we simply substitute
2
v  u  at into s 2 1 (u 
v)t
s  1 (u  (u  at))t  s  1 (2u  at)t  s  1 (2ut  at 2 ) s  ut  1 at 2
2 2 2 2

This can also be found if we remember that the area under a velocity-time graph represents the distance
travelled/displacement. The area under the line equals the area of rectangle A + the area of triangle B.
(v  u)
Area = Displacement = s = ut  21 (v  u)t since a  t then at  (v  u) so the equation becomes
s  ut 2 (at)t which then becomes equation
1

3
Equation 4
(v  u)
If we rearrange equation 1 into t  a which we will then substitute into equation 2:

(v  u)
s  21 (u  v)t  s  21 (u  v) a  as  21 (u  v)(v  u) 
2as  (v2  uv  uv  u 2 )  2as  v 2  u 2 v2  u 2 
2as
Any question can be solved as long as three of the variables are given in the question.
Write down all the variables you have and the one you are asked to find, then see which equation you can use.
These equations can only be used for motion with UNIFORM ACCELERATION.
 Unit 2
Lesson 7
Terminal Velocity and Projectiles
To know what terminal velocity is and how it occurs
Learning
Outcomes To be know how vertical and horizontal motion are connected
To be able to calculate the horizontal and vertical distance travelled by a projectile N. DWYER

Acceleration Due To Gravity (Also seen in GCSE Physics 2)

An object that falls freely will accelerate towards the Earth because of the force of gravity acting on it.
The size of this acceleration does not depend mass, so a feather and a bowling ball accelerate at the same rate.
On the Moon they hit the ground at the same time, on Earth the resistance of the air slows the feather more
than the bowling ball.
The size of the gravitational field affects the magnitude of the acceleration. Near the surface of the Earth the
gravitational field strength is 9.81 N/kg. This is also the acceleration a free falling object would have on Earth. In
the equations of motion a = g = 9.81 m/s.
Mass is a property that tells us how much matter it is made of.
Mass is measured in kilograms, kg
Weight is a force caused by gravity acting on a mass:
weight = mass x gravitational field strength w
mg Weight is measured in Newtons, N
Terminal Velocity (Also seen in GCSE Physics 2)
If an object is pushed out of a plane it will
accelerate towards the ground because of its
weight (due to the Earth’s gravity). Its velocity will
increase as it falls but as it does, so does the drag
forces acting on the object (air resistance).
Eventually the air resistance will balance the weight
of the object. This means there will be no overall
force which means there will be no
acceleration. The object stops accelerating and has
reached its terminal velocity.

Projectiles
An object kicked or thrown into the air will follow a
parabolic path like that shown to the right.
If the object had an initial velocity of u, this can be
resolved into its horizontal and vertical velocity (as
we have seen in Lesson 2)
The horizontal velocity will be ucos and the vertical velocity will be usin. With these we can solve projectile
questions using the equations of motion we already know.

Horizontal and Vertical Motion

The diagram shows two balls that are released at the same time, one is released and the other has a horizontal
velocity. We see that the ball shot from the cannon falls at the same rate at the ball that was released. This is
because the horizontal and vertical components of motion are independent of each other.

Horizontal: The horizontal velocity is constant; we see that the

fired ball covers the same horizontal (across) distance with
each second.
Vertical: The vertical velocity accelerates at a rate of g (9.81m/s2).
We can see this more clearly in the released ball; it covers
more distance each second.

The horizontal velocity has no affect on the vertical velocity. If a

ball were fired from the cannon at a high horizontal velocity it
would travel further but still take the same time to reach the
ground.
 Unit 2
Lesson 8
Newton’s Laws
To know and be able to use Newton’s 1st law of motion, where appropriate
Learning
Outcomes To know and be able to use Newton’s 2nd law of motion, where appropriate
To know and be able to use Newton’s 3rd law of motion, where appropriate N. DWYER

Newton’s 1st Law

An object will remain at rest, or continue to move with uniform velocity, unless it is acted upon by an external
resultant force.
Newton’s 2nd Law
The rate of change of an object’s linear momentum is directly proportional to the resultant external force. The
change in the momentum takes place in the direction of the force.
Newton’s 3rd Law
When body A exerts a force on body B, body B exerts an equal but opposite force on body A.
Force is measured in Newtons,
N
Say What?
Newton’s 1st Law
If the forward and backward forces cancel out, a stationary object will remain stationary.
If the forward forces are greater than the backwards forces, a stationary object will begin to move forwards.
If the forward and backward forces cancel out, a moving object will continue to move with constant velocity.
If the forward forces are greater than the backward forces, a moving object will speed up.
If the backward forces are greater than the forward forces, a moving object will slow down.
Newton’s 2nd Law
The acceleration of an object increases when the force is increased but decreases when the mass is
F
increased: F
a  m but we rearrange this and use
ma
Newton’s 3rd Law
Forces are created in pairs.
As you sit on the chair your weight pushes down on the chair, the chair also pushes up against you.
As the chair rests on the floor its weight pushes down on the floor, the floor also pushes up against the chair.
The forces have the same size but opposite directions.
Riding the Bus
Newton’s 1st Law
You get on a bus and stand up. When the bus is stationary you feel no force, when the bus accelerates you feel
a backwards force. You want to stay where you are but the bus forces you to move. When the bus is at a
constant speed you feel no forwards or backwards forces. The bus slows down and you feel a forwards force.
You want to keep moving at the same speed but the bus is slowing down so you fall forwards. If the bus turns
left you want to keep moving in a straight line so you are forced to the right (in comparison to the bus). If the
bus turns right you want to keep moving in a straight line so you are forced left (in comparison to the bus).
Newton’s 2nd Law
As more people get on the bus its mass increases, if the driving force of the bus’s engine is constant we can see
that it takes longer for the bus to gain speed.
Newton’s 3rd Law
As you stand on the bus you are pushing down on the floor with a force that is equal to your weight. If this was
the only force acting you would begin to move through the floor. The floor is exerting a force of equal
magnitude but upwards (in the opposite direction).
Taking the Lift
Newton’s 1st Law
When you get in the lift and when it moves at a constant speed you feel no force up or down. When it sets off
going up you feel like you are pushed down, you want to stay where you are. When it sets off going down you
feel like you are lighter, you feel pulled up.
Newton’s 2nd Law
As more people get in the lift its mass increases, if the lifting force is constant we can see that it takes longer for
the lift to get moving. Or we can see that with more people the greater the lifting force must be.
Newton’s 3rd Law
As you stand in the lift you push down on the floor, the floor pushes back.
 Unit 2
Lesson 9
Work, Energy and Power
To be able to calculate work done (including situations involving an inclined plane)
Learning
Outcomes To be able to calculate the power of a device
To be able to calculate efficiency and percentage efficiency N. DWYER

Energy (Also seen in GCSE Physics 1)

We already know that it appears in a number of different forms and may be transformed from one form to
another. But what is energy? Energy is the ability to do work.
We can say that the work done is equal to the energy transferred
Work done = energy transferred W E

Work Done (Also seen in GCSE Physics 2)

In Physics we say that work is done when a force moves through a distance and established the equation
Work Done = Force x Distance moved in the direction of the force W  Fs
Work Done is measured in Joules, J
Force is measured in Newtons, N
Distance is measured in metres, m
The distance moved is not always in the direction of the force. In the diagram we can see that the block moves
in a direction that is  away from the ‘line of action’ of the force. To calculate the work done we must calculate
the distance we move in the direction of the force or the size of the force in the direction of the distance
moved. Both of these are calculated by resolving into horizontal and vertical components.
Work Done = Force x Distance moved in the direction of the force
Work Done = Size of Force in the direction of movement x Distance moved
Work Done = Fs cos

 or
Power (Also seen in GCSE Physics 1 and AS Unit 1)
Power is a measure of how quickly something can transfer energy. Power is linked to energy by the equation:
Power is measured in Watts, W
E
EnergyTransferred P Energy is measured in Joules, J
Power  t Time is measured in seconds, s
But Work Done = timetaken
Energy Transferred so we can say that power is a measure of how quickly work can be done.
WorkDone
Power 
W
timetaken P  t
Now that we can calculate Work Done we can derive another equation for calculating power:
W Fs s
We can substitute W  Fs into P  to become P  this can be separated into P  F .
t
t
s tP  Fv
t  v so we can write
Velocity is measured in metres per second, m/s or ms-1
Efficiency (Also seen in GCSE Physics 1)
We already know that the efficiency of a device is a measure of how much of the energy we put in is wasted.
Efficiency = useful energy transferred by the device this will give us a number less
than 1 total energy supplied to the device
Useful energy means the energy transferred for a purpose, the energy transferred into the desired form.
Since power is calculated from energy we can express efficiency as:
Efficiency = useful output power of the device again this will give us a number less than 1
input power to the device
To calculate the efficiency as a percentage use the following:
percentage efficiency = efficiency x 100%
 Unit 2
Lesson 10
Conservation of Energy
To be able to calculate gravitational potential energy
Learning
Outcomes To be able to calculate kinetic energy
To be able to solve problems involving the conversion of energy N. DWYER

Energy Transformations (Also seen in GCSE Physics 1)

We already know that energy cannot be created or destroyed, only transformed from one type to another and
transferred from one thing to another. Eg a speaker transforms electrical energy to sound energy with the
energy itself is being transferred to the surroundings.
An isolated (or closed) system means an energy transformation is occurring where none of the energy is lost to
the surroundings. In reality all transformations/transfers are not isolated, and all of them waste energy to the
surroundings.

Kinetic Energy (Also seen in GCSE Physics 2)

Kinetic energy is the energy a moving object has. Let us consider a car that accelerates from being stationary
(u=0) to travelling at a velocity v when a force, F, is applied.
v
The time it takes to reach this velocity is give by v  u  at  v  at  t
 a
v 2
The distance moved in this time is given by s  21 (u  v)t  s  21 (v)t  s  12 (v)  s 1v
a 2
a
Energy transferred = Work Done, Work Done = Force x distance moved and Force = mass x acceleration
v2
E  W  E  Fs  E  mas  E  ma 1 E K  1 mv2 2
2
a
Velocity is measured in metres per second, m/s
Mass is measured in kilograms, kg
Kinetic Energy is measured in Joules, J
Gravitational Potential Energy
This type of potential (stored) energy is due to the position of an object. If an object of mass m is lifted at a
constant speed by a height of h we can say that the acceleration is zero. Since F=ma we can also say that the
overall force is zero, this means that the lifting force is equal to the weight of the object  F=mg
We can now calculate the work done in lifting the object through a height, h.
WD  Fs  WD  (mg)h  WD  mgh
Since work done = energy transferred EP 
mgh which is measured in metres, m
Height is a measure of distance
Gravitational Potential Energy is measured in Joules, J
Work Done against….
In many situations gravitational potential energy is converted into kinetic energy, or vice versa. Some everyday
examples of this are:
Swings and pendulums If we pull a pendulum back we give it GPE, when it is released it falls, losing its GPE but
speeding up and gaining KE. When it passes the lowest point of the swing it begins to rise (gaining GPE) and
slow down (losing KE).
Bouncing or throwing a ball Holding a ball in the air gives it GPE, when we release this it transforms this into KE.
As it rises it loses KE and gains GPE.
Slides and ramps A ball at the top of a slide will have GPE. When it reaches the bottom of the slide it has lost all
its
GPE, but gained KE.

In each of these cases it appears as though we have lost energy. The pendulum doesn’t swing back to its original
height and the ball never bounces to the height it was released from. This is because work is being done against
resistive forces.
The swing has to overcome air resistance whilst moving and the friction from the top support. The
ball transforms some energy into sound and overcoming the air resistance.
Travelling down a slide transforms energy into heat due to friction and air resistance

The total energy before a transformation = The total energy after a transformation
 Unit 2
Lesson 11
Hooke’s Law
To be able to state Hooke’s Law and explain what the spring constant is
Learning
Outcomes To be able to describe how springs behave in series and parallel
To be able to derive the energy stored in a stretched material N. DWYER

Hooke’s Law
If we take a metal wire or a spring and hang it from the ceiling it will have a natural, unstretched length of l
metres. If we then attach masses to the bottom of the wire is will begin to increase in length (stretch). The
amount of length it has increased by we will call the extension and represent by e.
If the extension increases proportionally to the force applied it follows Hooke’s Law:
The force needed to stretch a spring is directly proportional to the extension of the spring from its natural
length
So
Weitcan
takes twice
write thisasinmuch forceform:
equation to extend a spring twice
F as efar and half the force
or to extend it half as far.
F
Here k is the constant that shows us how much extension in length we would get for a given force. It ke is called...

The Spring Constant

The spring constant gives us an idea of the stiffness (or stretchiness) of the material.
F
If we rearrange Hooke’s Law we get: k
 e
If we record the length of a spring, add masses to the bottom and measure its
extension we can plot a graph of force against extension. The gradient of this graph will
be equal to the spring constant.
A small force causes a large extension the spring constant will be small – very stretchy
A large force causes a small extension the spring constant will be large – not stretchy
Spring Constant is measured in
Newtons per metre, N/m
Springs in Series
The
1 combined
1  1 spring constant of spring A and spring B connected in series is given by:
If A and B are identical this becomes:
kT kA kB

1 1 1  1 2  kT 
kT  k  k kT  k 2
k
Since this gives us a smaller value for the spring constant, applying the same force
produces a larger extension. It is stretchier
Springs in Parallel
The combined spring constant of spring A and spring B connected in parallel is:
kT  k A  kB so if A and B are identical this becomes:
kT  k  k  kT  2k
Since this gives us a larger value for the spring constant applying the same force
produces a smaller extension. It is less stretchy

Energy Stored (Elastic Strain Energy)

We can calculate the energy stored in a stretched material by considering the work done on it.
We defined work done as the force x distance moved in the direction of the force or W 
Work done is equal to the energy transferred, in this case transferred to the material, so: Fs E 
The distance moved is the extension of the material, e, making the equation: Fs E 
Fe (F 
The force is not constant; it increases from zero to a maximum of F. The average force is
0) 2
given by:
(F  0) E1
If we bring these terms together we get the equation E  2 e which simplifies to: 2
Fe
This is also equal to the area under the graph of force against extension.
We can write a second version of this equation by substituting our top equation of F  ke into the one
E  1 Fe  E  1 (ke)e  above. E  21 ke2
2 2
 Unit 2
Lesson 12
Stress and Strain
To know what stress is, be able to explain it, calculate it and state its units
Learning
Outcomes To know what strain is, be able to explain it, calculate it and state its units
To be able to calculate the elastic strain energy per unit volume N. DWYER

Deforming Solids
Forces can be used to change the speed, direction and shape of an object. This section of Physics looks at using
forces to change of shape of a solid object, either temporarily or permanently.
If a pair of forces are used to squash a material we say that they are compressive forces.
If a pair of forces is used to stretch a material we say that they are tensile forces.

Tensile Stress, σ
Tensile stress is defined as the force applied per unit cross-sectional area (which is the same as pressure).
This is represented by the equations:

F F
stress  
A A
The largest tensile stress that can be applied to a material before it breaks is called the ultimate tensile stress
(UTS). Nylon has an UTS of 85 MPa whilst Stainless steel has a value of 600 MPa and Kevlar a massive 3100 MPa
Stress is measured in Newtons per metre squared, N/m2 or N m-2
Stress can also be measured in Pascals, Pa
A tensile stress will cause a tensile strain. Stress causes Strain

Tensile Strain, ε
Tensile strain is a measure of how the extension of a material compares to the original, unstretched length.
This is represented by the equations:

e
strain  
l l
Steel wire will undergo a strain of e0.01 before it breaks. This means it will stretch by 1% of its original length
then break. Spider silk has a breaking strain of between 0.15 and 0.30, stretching by 30% before breaking
Strain has no units, it is a ratio of two
lengths

Stress-Strain Graphs
A stress-strain graph is very useful for comparing different materials.
Here we can see how the strain of two materials, a and b, changes when a stress is
applied.
If we look at the dotted lines we can see that the same amount of stress causes a
bigger strain in b than in a. This means that b will increase in length more than a
(compared to their original lengths).

Elastic Strain Energy

We can build on the idea of energy stored from the previous lesson now that we know what stress and strain
are.
It We can
is given bywork out the amount of elastic strain energy that is stored per unit volume of the
the equation: E material.
1
stress 
2
There are two routes we can take to arrive at this result: strain
Equations
If we start with the equation for the total energy stored in the material: E  21
The volume of the material is given by: VFe Al
1
Fe Fe
Now divide the total energy stored by the volume: E  2 which can be written E  21 A l
as: Al
If we compare the equation to the equations we know for E  21 stress 
stress and strain we see that: strain
The area under a stress-strain graph gives us the elastic strain energy per unit volume (m3). The area is given by:
Graphs
A  1 base height  A  1 strain  stress or A  1 stress  strain  E  1 stress 
strain
2 2 2 2
 Unit 2
Lesson 13
Bulk Properties of Solids
To be able to calculate density and explain what it is
Learning
Outcomes To be able to explain what elastic, plastic, yield point, breaking stress, stiff, ductile and brittle are
To be able to label these qualities on stress-strain graphs N. DWYER

Density, ρ
Density is the mass per unit volume of a material, a measure of how much mass each cubic metre
of volume contains. Density if given by the equation:  Vm
Where ρ is density, m is mass in kilograms and V is volume in metres cubed.
Density is measured in kilograms per metre cubed, kg/m3 or kg m-3
Elasticity
Materials extend in length when a stress is applied to them (masses hung from them). A material can be
described as elastic if it returns to its original length when the stress is removed. They obey Hooke’s Law as
extension is proportional to the force applied.
Limit of Proportionality, P
Up to this point the material obeys Hooke’s Law; extension is proportional to the force applied.
Elastic Limit, E
The elastic limit is the final point where the material will return to its original length if we remove the stress
which is causing the extension (take the masses off). There is no change to the shape or size of the material.
We say that the material acts plastically beyond its elastic limit.
Yield Point, Y
Beyond the elastic limit a point is reached where small increases in stress cause a massive increase in extension
(strain). The material will not return to its original length and behaves like a plastic.
Plasticity
Materials extend in length when a stress is applied to them (masses hung from them). A material can be
described as plastic if it does not return to its original length when the stress is removed. There is a permanent
change to its shape
Breaking Stress – Ultimate Tensile Strength, UTS
This is the maximum amount of stress that can be applied to the material without making it break. It is
sometimes referred to as the strength of the material.
Breaking Point, B
This is (surprisingly?) the point where the material breaks.
Stiffness
If different materials were made into wires of equal dimensions, the stiffer materials bend the least.
Stiff materials have low flexibility
Ductility
A ductile material can be easily and permanently stretched. Copper is a good example, it can easily
be drawn
out into thin wires. This can be seen in graph d below.
Brittleness
A brittle material will extend obeying Hooke’s Law when a stress is applied to it. It will suddenly fracture with no
warning sign of plastic deformation. Glass, pottery and chocolate are examples of brittle materials.
Stress-Strain Graphs

In the first graph we see a material that stretches, shows plastic behaviour and eventually breaks.
In the second graph we can see that material a is stiffer than material b because the same stress causes a
greater strain in b.
In the third graph we see materials c and e are brittle because they break without showing plastic behaviour.
The fourth graph shows how a material can be permanently deformed, the wire does not return to its original
length when the stress is removed (the masses have been removed).
 Unit 2
Lesson 14
The Young Modulus
To know what the Young Modulus is, be able to explain it, calculate it and state its units
Learning
Outcomes To be able to describe an experiment for finding the Young Modulus
To be able to calculate the Young Modulus from a stress-strain graph N. DWYER

The Young Modulus, E

The Young Modulus can be thought of as the stiffness constant of a material, a measure of how much strain will
result from a stress being applied to the material. It can be used to compare the stiffness of different materials
even though their dimensions are not the same.
The Young Modulus only applies up to the limit of proportionality of a material.
stress 
YoungModulus or in equation terms we have E
 strain  
F
F e  
A
We have equations for stress   A and strain  l which makes the equation look like this: E   
e
 l 
Fl
E
F l
An easier way of writing this is E     which becomes: Ae
A e
The Young Modulus is measured in Newtons per metre squares, N/m2 or N m-2

Stress-Strain Graphs
The Young Modulus of a material can be found from its stress-strain graph.

y stress
Since gradient  x , this becomes gradient  strain for our graph. Our top equation stated that
stress
YoungModulus so we see that the gradient of a stress-strain graph gives us the Young Modulus.
 strain
This only applied to the straight line section of the graph, where gradient (and Young Modulus) are constant.

Measuring the Young Modulus

Here is a simple experimental set up for finding the Young Modulus of a material.

 A piece of wire is held by a G-clamp, sent

over a pulley with the smallest mass attached
to it. This should keep it straight without
extending it.
 Measure the length from the clamp to the
pointer. This is the original length
(unstretched).
 Use a micrometer to measure the
diameter
of the wire in several places. Use this to
calculate the cross-sectional area of the
wire.
 Add a mass to the loaded end of the wire.
 Record the extension by measuring how far the pointer has moved from its
start position.
 Repeat for several masses but ensuring the elastic limit is not reached.
 Remove the masses, one at a time taking another set of reading of the
extension.
 Calculate stress and strain for each mass.
 Plot a graph of stress against strain and calculate the gradient of the line which
gives the Young Modulus.

Here is a more precise way of finding the Young Modulus but involves taking the
same measurements of extension and force applied.
 Unit 2
Lesson 15
Progressive Waves
To be know the basic measurements of a wave
Learning
Outcomes To be able to calculate the speed of any wave
To be know what phase and path difference are and be able to calculate them N. DWYER

Waves
All waves are caused by oscillations and all transfer energy without transferring matter. This means that a water
wave can transfer energy to you sitting on the shore without the water particles far out to sea moving to the
beach.
Here is a diagram of a wave; it is one type of wave called a
transverse wave. A wave consists of something (usually
particles) oscillating from an equilibrium point. The wave
can be described as progressive; this means it is moving
outwards from the source.
We will now look at some basic
measurements and characteristics or
Amplitude, A waves. Amplitude is measured in metres, m
The amplitude of a wave is the maximum displacement of the particles from the equilibrium position.
Wavelength, Wavelength is measured in metres, m
λ The wavelength of a wave is the length of one whole cycle. It can be measured between two adjacent peaks,
troughs or any point on a wave and the same point one wave later.
Time Period, T Time Period is measured in seconds, s
This is simply the time is takes for one complete wave to happen. Like wavelength it can be measured as the
time it takes between two adjacent peaks, troughs or to get back to the same point on the wave.
Frequency, f Frequency is measured in Hertz, Hz
Frequency is a measure of how often something happens, in this case how many complete waves occur in every
1
1 f 
second. It is linked to time period of the wave by the following equations: T  f and T
Wave Speed, c Wave Speed is measured in metres per second, m s-1
The speed of a wave can be calculated using the following equations: c
Here c represents the speed of the wave, f the frequency and λ the wavelength. f
Phase Difference Phase Difference is measured in radians, rad
If we look at two particles a wavelength apart (such as C and G) we would see that they are oscillating in time
with each other. We say that they are completely in phase. Two points half a wavelength apart (such as I and K)
we would see that they are always moving in opposite directions. We say that they are completely out of phase.
The phase difference between two points depends on what fraction of a wavelength lies between them

B C D E F G H I J K L M
Phase Difference ½π 1π 1½π 2π 2½π 3π 3½π 4π 4½π 5π 5½π 6π
from A (radians)
Phase Difference 90 180 270 360 450 540 630 720 810 900 990 1080
from A (degrees)
Path Difference Path Difference is measured in wavelengths, λ
If two light waves leave a bulb and hit a screen the difference in how far the waves have travelled is called the
path difference. Path difference is measured in terms of wavelengths.
B C D E F G H I J K L M
Path Difference ¼λ ½λ ¾λ 1λ 1¼λ 1½λ 1¾λ 2λ 2¼λ 2½λ 2¾λ 3λ
from A
So two waves leaving A with one making it to F and the other to J will have a path difference of 1 wavelength (1λ).
 Unit 2
Lesson 16
Longitudinal and Transverse Waves
To be able explain the differences between longitudinal and transverse waves
Learning
Outcomes To know examples of each
To be explain what polarisation is and how it proves light is a transverse wave N. DWYER

Waves
All waves are caused by oscillations and all transfer energy without transferring matter. This means that a
sound wave can transfer energy to your eardrum from a far speaker without the air particles by the speaker
moving into your ear. We will now look at the two types of waves and how they are different

Longitudinal Waves
Here is a longitudinal wave; the oscillations are parallel to the direction of propagation (travel).
Where the particles are close together we call a compression and where they are spread we call a rarefaction.
The wavelength is the distance from one compression or rarefaction to the next.
The amplitude is the maximum distance the particle moves from its equilibrium position to the right of left.

Example:
sound waves
Transverse Waves
Here is a transverse wave; the oscillations are perpendicular to the direction of propagation.
Where the particles are displaced above the equilibrium position we call a peak and below we call a
trough. The wavelength is the distance from one peak or trough to the next.
The amplitude is the maximum distance the particle moves from its equilibrium position up or down.

Examples:
water waves,
Mexican waves and
waves of the EM spectrum
EM waves are produced from varying electric and magnetic field.

Polarisation
Polarisation restricts the oscillations of a wave to one plane. In the diagrams the light is initially oscillating in all
directions. A piece of Polaroid only allows light to oscillate in the same direction as it.
In the top diagram the light passes through a vertical plane Polaroid and becomes
polarized in the vertical plane. This can then pass through the second vertical
Polaroid.
In the middle diagram the light becomes polarized in the horizontal
plane.
In the bottom diagram the light becomes vertically polarized but
this cannot pass through a horizontal plane Polaroid.
This is proof that the waves of the EM spectrum are transverse
waves. If they were longitudinal waves the forwards and backwards
motion would not be stopped by crossed pieces of Polaroid; the
bottom set up would emit light.
Applications
TV aerials get the best reception when they point to the transmission
source so they absorb the maximum amount of the radio waves.
 Unit 2
Lesson 17
Superposition and Standing Waves
To know and be able to explain what standing waves are and how they are formed
Learning
Outcomes To know what nodes and antinodes are
To be able to sketch the standing wave produced at different frequencies N. DWYER

Superposition
Here are two waves that have amplitudes of 1.0 travelling in opposite directions:

Superposition is the process by which two waves combine into a single wave form when they overlap.
If we add these waves together the resultant depends on where the peaks of the waves are compared to each
other. Here are three examples of what the resultant could be: a wave with an amplitude of 1.5, no resultant
wave at all and a wave with an amplitude of 2.0

Stationary/Standing Waves
When two similar waves travel in opposite directions they can
superpose to form a standing (or stationary) wave. Here is the
experimental set up of how we can form a standing wave on a
string. The vibration generator sends waves down the string at a
certain frequency, they reach the end of the string and reflect
back at the same frequency. On their way back the two waves
travelling in opposite direction superpose to form a standing
wave made up of nodes and antinodes.
Nodes Positions on a standing wave which do not vibrate. The
waves combine to give zero displacement
Antinodes Positions on a standing wave where there is a maximum
displacement.

Standing Waves Progressive Waves

Amplitude Maximum at antinode and zero at nodes The same for all parts of the wave
Frequency All parts of the wave have the same frequency All parts of the wave have the same frequency
Wavelength Twice the distance between adjacent nodes The distance between two adjacent peaks
Phase All points between two adjacent nodes in phase Points one wavelength apart in phase
Energy No energy translation Energy translation in the direction of the wave
Waveform Does not move forward Moves forwards

Harmonics
As we increase the frequency of the vibration generator we will see standing
waves being set up. The first will occur when the generator is vibrating at the
fundamental frequency, f0, of the string.
First Harmonic f = f0 λ=2L
2 nodes and 1 antinode
Second Harmonic f = 2f0 λ=L
3 nodes and 2 antinodes
Third Harmonic f = 3f0 λ=⅔
4 nodes and 3 antinodes L
Forth Harmonic
5 nodes and 4 antinodes f = 4f0 λ=½
L
 Unit 2
Lesson 18
Refraction
To be able to calculate the refractive index of a material and to know what it tells us
Learning
Outcomes To be able to describe and explain the direction light takes when entering a different material
To be able to calculate the relative refractive index of a boundary N. DWYER

Refractive Index
The refractive index of a material is a measure of how easy it is for light to travel through it. The refractive index
of material s can be calculated using:

n
c
cs
where n is the refractive index, c is the speed of light in a
vacuum and cs is the speed of light in material s. c  n  n1
If light can travel at c in material x then the refractive index is: n R
c c
 e
cc c
If light can travel at c/2 in material y then the refractive index is: n x f n   n2
cy r
c
2
a
The higher the refractive index the slower light can travel through it
c
The higher the refractive index the denser the material
t
Bending Light i
When light passes from one material to another it is not only the speed of the v
light that changes, the direction can change too. e
If the ray of light is incident at 90° to the material then there is no change in
direction, only speed. I
It may help to imagine the front of the ray of light as the front of a car to n
determine the direction the light will bend. Imagine a lower refractive index as grass andd a higher refractive
index at mud. e
Entering a Denser Material x
The car travels on grass until tyre A reaches the mud. It is harder to move through ,
mud so A slows down but B can keep moving at the same speed as before. The car now
points in a new direction. n
Denser material – higher refractive index – bends towards the Normal ,
Entering a Less Dense Material
The car travels in mud until tyre A reaches the grass. It is easier to move across grass hso A
can speed up but B keeps moving at the same speed as before. The car now points a
in a new direction. s
Less dense material – lower refractive index – bends away from the Normal
Relative Refractive Index n
Whenever two materials touch the boundary between them o will have a refractive index
dependent on the refractive indices of the two materials. We call this the relative
refractive index. u
n
When light travels from material 1 to material 2 we can calculate the relative
i
refractive index of the boundary using any of the following:
t
n n c
1 2  2
 1
 s
n1 c2 sin 2
sin1
Relative Refractive Index, 1n2, has no units
Some questions may involve light travelling through several layers of
materials. Tackle one boundary at a time.

wn g  ng  cw  ---------------------------->
nw cg
sinw
sin g
n
g a ---------------------------->
nng cca sin
g

sina
 a
 
g
 Unit 2
Lesson 19
Total Internal Reflection
To know what the critical angle is and be able to calculate it
Learning
Outcomes To be able to explain what fibre optics are and how they are used
To be able to explain how cladding helps improve the efficiency of a fibre optic N. DWYER

Total Internal Reflection (Also seen in GCSE Physics 3)

We know that whenever light travels from one material to another the majority of the light refracts but a small
proportion of the light also reflects off the boundary and stays in the first material.
When the incident ray strikes the boundary at an angle less than the critical angle the light refracts into the
second material.
When the incident ray strikes the boundary at an angle equal to the critical angle all the light is sent along the
boundary between the two materials.
When the incident ray strikes the boundary at an angle greater than the critical angle all the light is reflected
and none refracts, we say it is total internal reflection has occurred.

Critical Angle (Also seen in GCSE Physics 3)

We can derive an equation that connects the critical angle with the refractive indices of the materials.
sin1 n sin1 n2
 2 but at the critical angle θ2 is equal to 90° which makes sinθ2 = 1 
sin2  1 n1
n1
n2
θ1 is the critical angle which we represent as θC making the equation: sinC
 n1

1
When the second material is air n2 = 1, so the equation becomes: sin C  1
or n1 sinC
1
n
Optical Fibres/Fibre Optics 
An optical fibre is a thin piece of flexible glass. Light can travel down
it due to total internal reflection. Thier uses include:
*Communication such as phone and TV signals: they can carry more
information that electricity in copper wires.
*Medical endoscopes: they allow us to see down them and are
flexible so they don’t cause injury to the patient.
Cladding
Cladding is added to the outside of an optical fibre to reduce the
amount of light that is lost. It does this by giving the light rays a
second chance at TIR as seen in the diagram.
It does increase the critical angle but the shortest path through
the
optical fibre is straight through, so only letting light which stays in
the core means the signal is transmitted quicker.
Consider the optical fibre with a refractive index of 1.5…
Without cladding n2 = 1 sinC  n2 sin C  1 C 
n 41.8
1 1.5
With cladding n2 = 1.4 sin C  n2 sin C C 
n1 1.5
1.4 69.0

If the cladding had a lower refractive index than the core it is easier for light to travel through so the light would
bend away from the normal, Total Internal Reflection.
If the cladding had a higher refractive index than the core it is harder for light to travel through so the light
would bend towards the normal, Refraction.
 Unit 2
Lesson 20
Interference
To be able to explain what interference and coherence is
Learning
Outcomes To be able to explain Young’s double slit experiment and a double source experiment
To be able to use the equation to describe the appearance of fringes produced N. DWYER

Interference
Interference is a special case of superposition where the waves that combine are coherent. The waves overlap
and form a repeating interference pattern of maxima and minima areas. If the waves weren’t coherent the
interference pattern would change rapidly and continuously.
Coherence: Waves which are of the same frequency, wavelength, polarisation and amplitude and in a constant
phase relationship. A laser is a coherent source but a light bulb is not.
Constructive Interference: The path difference between the waves is a whole number of wavelengths so the
waves arrive in phase adding together to give a large wave. 2 peaks overlap
Destructive Interference: The path difference between the waves is a half number of wavelengths so the waves
arrive out of phase cancelling out to give no wave at all. A peak and trough overlap

Young’s Double Slit Experiment

In 1803 Thomas Young settled a debate started over 100 years earlier between Newton and
Huygens by demonstrating the interference of light. Newton thought that light was made
up of tiny particles called corpuscles and Huygens thought that light was a wave,
Young’s interference of light proves light is a wave. Here is
Young’s double slit set up, the two slits act as coherent
sources of waves

Interference occurs where the light from the two slits

overlaps. Constructive interference produces bright
areas, while deconstructive interference produces dark
areas. These areas are called interference fringes.

Fringes
There is a central
bright
fringe directly behind the midpoint between the slits with
more fringes evenly spaced and parallel to the slits.
As we move away from the centre of the screen we see the
intensity of the bright fringes decreases.

Double Source Experiment

The interference of sound is easy to demonstrate with two speakers connected to the same signal generator.
Waves of the same frequency (coherent) interfere with each other. Constructive interference produces loud
fringes, while deconstructive interference produces quiet fringes.

Derivation
We can calculate the separation of the fringes (w) if we
consider the diagram to the right which shows the first
bright fringe below the central fringe. The path
difference between the two waves is equal to one
whole wavelength (λ) for constructive interference.
If the distance to the screen (D) is massive compared to
the separation of the sources (s) the angle (θ) in the
large triangle can be assumed the same as the angle in the
smaller triangle.
Opposite 
sin For the small triangle: sin  For the large triangle: sin 
w
 Hypotenuse
w s D
which rearranges to: w
D
 s D D s  s
Fringe Separation, Source Separation, Distance to Screen and Wavelength are measured in metres, m
w
 Unit 2
Lesson 21
Diffraction
To know what diffraction is and when it happens the most
Learning
Outcomes To be able to sketch the diffraction pattern from a single slit and a diffraction grating
To be able to derive dsinθ=n N. DWYER

Diffraction
When waves pass through a gap they spread
out, this is called diffraction. The amount of
diffraction depends on the size of the
wavelength compared to the size of the gap.
In the first diagram the gap is several times
wider than the wavelength so the wave only
spreads out a little.
In the second diagram the gap is closer to
the wavelength so it begins to spread out
more.
In the third diagram the gap is now roughly
the same size as the wavelength so it
spreads out the most.

Diffraction Patterns
Here is the diffraction pattern from light being shone through a single slit.
There is a central maximum that is twice as wide as the others and by far the
brightest. The outer fringes are dimmer and of equal width.
If we use three, four or more slits the interference maxima become brighter,
narrower and further apart.

Diffraction Grating
A diffraction grating is a series of narrow, parallel slits. They
usually have around 500 slits per mm.
When light shines on the diffraction grating several bright sharp
lines can be seen as shown in the diagram to the right.
The first bright line (or interference maximum) lies directly
behind
where the light shines on the grating. We call this the zero-order
maximum. At an angle of θ from this lies the next bright line
called the first-order maximum and so forth.
The zero-order maximum (n=0)
There is no path difference between neighbouring waves. They
arrive in phase and interfere constructively.
The first-order maximum (n=1)
There is a path difference of 1 wavelength between neighbouring
waves. They arrive in phase and interfere constructively.
The second-order maximum (n=2)
There is a path difference of 2 wavelengths between neighbouring
waves. They arrive in phase and interfere constructively.
Between the maxima
The path difference is not a whole number of wavelengths so the
waves arrive out of phase and interfere destructively.

Derivation
The angle to the maximaOpposite
depends on the wavelength of the light
sin of the
and the separation  sin   d sin 
Hypotenuse 
 an equation that links them by taking a closer look at two
slits. We can derive
For the nth order
neighbouring thegoing
waves opposite side
to the of the triangle
first-order
d
becomes
maximum. nλ, making the equation:
The distance to the screen is so much biggerd sinthan
 the distance between two slits that
n 
emerging waves appear to be parallel and can be treated that way.