Dimensioning

Engineering Drawing (UG-CE 2024)

Lec Engr. Muhammad Hamza Sabir

[email protected]
Office 111, SCEE (NICE)

1
 TOPICS

Introduction
Dimensioning components
Dimensioning object’ s features

Placement of dimensions.

2
Introduction

3
 ENGINEERING DESIGN
PROCESS RESULT TRANSFERRED
INFORMATION

Design Sketches
a part of ideas

Multiview
Shape
Create Drawing
drawings
1. Size, Location
Dimensioning
2. Non-graphic information

Manufacture
4
 DEFINITION
Dimensioning is the process of specifying part’ s
information by using of figures, symbols and notes.

This information are such as:

1. Sizes and locations of features
2. Material’s type This course
3. Number required
4. Kind of surface finish
5. Manufacturing process
6. Size and geometric tolerances
5
 DIMENSIONING SYSTEM

1. Metric system : ISO and JIS standards This

Examples 32, 32.5, 32.55, 0.5 (not .5) etc. course

2. Decimal-inch system
Examples 0.25 (not .25), 5.375 etc.

3. Fractional-inch system
1 3
Examples , 5 etc.
4 8
6
Dimensioning
Components

7
DIMENSIONING COMPONENTS
Extension lines
Dimension lines Drawn with
(with arrowheads) 4H pencil
Leader lines
Dimension figures
Notes : Lettered with
- local note 2H pencil.
- general note
8
 EXTENSION LINES
indicate the location on the object’s features that
are dimensioned.

9
 DIMENSION LINES
indicate the direction and extent of a dimension and
inscribe dimension figures.

10 27

13
1 23
o

43 10
 LEADER LINES

indicate details of the feature with a local note.

10 27 10 Drill, 2 Holes
R16

13
1 23
o

43 11
Recommended
Practices

12
 EXTENSION LINES
Leave a visible gap (≈ 1 mm) from a view and
start drawing an extension line.
Extend the lines beyond the (last) dimension line
1-2 mm.
COMMON MISTAKE
Visible gap

13
 EXTENSION LINES
Do not break the lines as they cross object lines.

COMMON MISTAKE
Continuous

14
 DIMENSION LINES
Dimension lines should not be spaced too close
to each other and to the view.

Leave a space at least

2 times of a letter height.
16

11
34
35

Leave a space at least

1 time of a letter height. 15
 DIMENSION FIGURES
The height of figures is suggested to be 2.5~3 mm.
Place the numbers at about 1 mm above dimension
line and between extension lines.

34 COMMON MISTAKE
11

11
34
16
 DIMENSION FIGURES
When there is not enough space for figure or
arrows, put it outside either of the extension lines.

Not enough space Not enough space

for figures for arrows
16.25
16.25 1 1 1

or

17
 DIMENSION FIGURES : UNITS
The JIS and ISO standards adopt the unit of

Length dimension in millimeters without

specifying a unit symbol “mm”.

Angular dimension in degree with a symbol “o”

place behind the figures (and if necessary
minutes and seconds may be used together).

18
DIMENSION FIGURES : ORIENTATION
1. Aligned method
The dimension figures are placed so that they
are readable from the bottom and right side of
the drawing.

2. Unidirectional method

The dimension figures are placed so that they

can be read from the bottom of the drawing.

Do not use both system on the same drawing or

on the same series of drawing (JIS Z8317) 19
EXAMPLE : Dimension of length using aligned method.
30
30

30

30
30

30

30
30

20
EXAMPLE : Dimension of length using unidirectional method.

30

30 30

30 30

30 30

30
21
EXAMPLE : Dimension of angle using aligned method.

45o
45

o
45

o
45o

45o
45

o
45
o

45o

22
EXAMPLE : Dimension of angle using unidirectional method.

45o
45o 45o

45o 45o

45o 45o

45o

23
 LOCAL NOTES
Place the notes near to the feature which they
apply, and should be placed outside the view.
Always read horizontally.

COMMON MISTAKE
10 Drill 10 Drill

10 Drill
≈ 10mm
Too far

24
Dimensioning
Practices

25
 THE BASIC CONCEPT
Dimensioning is accomplished by adding size and
location information necessary to manufacture
the object.

This information have to be

Clear
Complete
Facilitate the
- manufacturing method
- measurement method
26
EXAMPLE L L

Designed
part

L
S

L
S
To manufacture this part S
we need to know…
1. Width, depth and
thickness of the part.
S

2. Diameter and depth

of the hole.
“S” denotes size dimension.
3. Location of the holes. 27
“L” denotes location dimension.
 ANGLE
To dimension an angle use circular dimension
line having the center at the vertex of the angle.

COMMON MISTAKE

28
 ARC
Arcs are dimensioned by giving the radius, in the
views in which their true shapes appear.
The letter “R” is always lettered before the figures
to emphasize that this dimension is radius of an
arc.

0
20
0 20
R R
or

29
 ARC
The dimension figure and the arrowhead should
be inside the arc, where there is sufficient space.

Sufficient space Sufficient space Insufficient space

for both. for arrowhead only. for both.
Move figure outside Move both figure
and arrow outside
R 62.5
0
20

R 6.5
R

R 58.5

30
 ARC
Leader line must be radial and inclined with
an angle between 30 ~ 60 degs to the horizontal.

COMMON MISTAKE
R62.5 R62.5 R62.5
60
o

R62.5
R62.5 R62.5
30
o

31
 ARC
Use the foreshortened radial dimension line,
when arc’ s center locates outside the sheet or
interfere with other views.

Method 2
1

Drawing sheet 32
 FILLETS AND ROUNDS
Give the radius of a typical fillet only by using a
local note.
If all fillets and rounds are uniform in size,
dimension may be omitted, but it is necessary to
add the note “ All fillets and round are Rxx. ”
R6.5 R12

NOTE:
NOTE: All fillets and round are R6.5
All fillets and round are R6.5 unless otherwise specified.
33
Drawing sheet
 CURVE
The curve constructed from two or more arcs,
requires the dimensions of radii and center’s
location.
COMMON MISTAKE
Tangent point

34
 CYLINDER
Size dimensions are diameter and length.
Location dimension must be located from its
center lines and should be given in circular view.

Measurement
method

35
 CYLINDER
Diameter should be given in a longitudinal view
with the symbol “ ” placed before the figures.

 100

 70 36
 HOLES
Size dimensions are diameter and depth.
Location dimension must be located from its
center lines and should be given in circular view.

Measurement
method

37
 HOLES : SMALL SIZE
Use leader line and local note to specify diameter
and hole’s depth in the circular view.
1) Through thickness hole

xx xx Thru. xx Drill. xx Drill, Thru.

or or or

38
 HOLES : SMALL SIZE
Use leader line and local note to specify diameter
and hole’s depth in the circular view.

2) Blind hole
xx, yy Deep xx Drill, yy Deep

or

Hole’s
depth

39
 HOLES : LARGE SIZE

Use extension and Use diametral Use leader line

dimension lines dimension line and note

xx

40
 HOLES
COMMON MISTAKE
xx xx
xx Rxx

xx

xx

41
 CHAMFER
Use leader line and note to indicate linear
distance and angle of the chamfer.


S 
S

For a 45o chamfer

or

CS 42
S S
 ROUNDED-END SHAPES
Dimensioned according to the manufacturing
method used.

12 Center to Center Distance

R12

21
5

43
 ROUNDED-END SHAPES
Dimensioned according to the manufacturing
method used.

R12
12

21

Center to Center Distance

5

44
 ROUNDED-END SHAPES
Dimensioned according to the manufacturing
method used.
R12

12

16 21

45
 ROUNDED-END SHAPES
Dimensioned according to the manufacturing
method used.
R12
12

27

Tool cutting distance

46
 ROUNDED-END SHAPES
Dimensioned according to the standard sizes of
another part to be assembled or manufacturing
method used.
Key
(standard part)

25

47
 ROUNDED-END SHAPES
Dimensioned according to the standard sizes of
another part to be assembled or manufacturing
method used.

20

48
Placement of
Dimensions

49
 RECOMMENDED PRACTICE
1. Extension lines, leader lines should not cross
dimension lines.

POOR GOOD

50
 RECOMMENDED PRACTICE
2. Extension lines should be drawn from the nearest
points to be dimensioned.

POOR GOOD

51
 RECOMMENDED PRACTICE
3. Extension lines of internal feature can cross visible
lines without leaving a gap at the intersection point.

WRONG CORRECT

52
 RECOMMENDED PRACTICE
4. Do not use object line, center line, and dimension

line as an extension lines.

POOR GOOD

53
 RECOMMENDED PRACTICE
5. Avoid dimensioning hidden lines.

POOR GOOD

54
 RECOMMENDED PRACTICE
6. Place dimensions outside the view, unless
placing them inside improve the clarity.

POOR GOOD

55
 RECOMMENDED PRACTICE
6. Place dimensions outside the view, unless
placing them inside improve the clarity.

JUST OK !!! BETTER

56
 RECOMMENDED PRACTICE
7. Apply the dimension to the view that clearly show
the shape or features of an object.

POOR GOOD

57
 RECOMMENDED PRACTICE
8. Dimension lines should be lined up and grouped
together as much as possible.

POOR GOOD

58
 RECOMMENDED PRACTICE
9. Do not repeat a dimension.

POOR GOOD

59