William Stallings

Data and Computer

Communications
7th Edition

Chapter 10
Circuit Switching and Packet
Switching

1
Switching Networks
• Long distance transmission is typically
done over a network of switched nodes
• Nodes not concerned with content of data
• End devices are stations
—Computer, terminal, phone, etc.
• A collection of nodes and connections is a
communications network
• Data routed by being switched from node
to node

2
Nodes
• Nodes may connect to other nodes only,
or to stations and other nodes
• Node to node links usually multiplexed
• Network is usually partially connected
—Some redundant connections are desirable for
reliability
• Two different switching technologies
—Circuit switching
—Packet switching

3
Simple Switched Network

4
Switching Activities
• Some nodes connect only to other nodes
(intermediary nodes). Sole purpose is to
switch data
• Some nodes have one or more stations
attached. They accept from and deliver
data to the attached station.
• Node-to-node links are usually multiplexed
• Multiple paths enhance reliability

5
Circuit Switching
• Originated in public telephone networks
• Well suited to analog transmission of voice signal
• Dedicated communication path between two
stations
• Three phases
— Establish
— Transfer
— Disconnect
• Must have switching capacity and channel
capacity to establish connection
• Must have intelligence to work out routing

6
Circuit Switching - Applications
• Inefficient
—Channel capacity dedicated for duration of
connection
—If no data, capacity wasted
• Set up (connection) takes time
• Once connected, transfer is transparent
• Developed for voice traffic (phone)

7
Public Circuit Switched Network

8
Telecom Components
• Subscriber
— Devices attached to network
• Subscriber line
— Link between subscriber and network
• Also called Local Loop or Subscriber Loop
— Almost all Local Loops are TPW
— Range from Few km up to tens of km
• Exchange
— Switching center in the network
— End office specific switching center that supports
subscribers
• Trunks
— Branches between exchanges
— Multiplexed

9
Circuit Establishment

10
Circuit Switching Concepts
• Digital Switch
— Provide transparent signal path between devices
— Typically allows full duplex transmission
• Network Interface
• Functions and h/w needed to connect
digital devices to the network
• Control Unit
— Establish connections - Generally on demand, Handle
and acknowledge requests, Determine if destination is
free,construct path
— Maintain connection
— Disconnect

11
Blocking or Non-blocking Circuit
Switching
• Blocking
—A network may not be able to connect stations
because all paths are in use (more stations
than path)
—Used on voice systems
• Short duration calls
• Non-blocking
—Permits all stations to connect (in pairs) at
once (at least as many paths as stations)
—Used for some data connections

12
Space Division Switching
• Developed for analog environment, but
carried over into digital
• Signal paths are physically separate (slide
15)
• Each connection requires dedicated path
(crossbar switch)

13
Crossbar switch
• Number of crosspoints grows as square of
number of stations
• Loss of crosspoint prevents connection
—Inefficient use of crosspoints
—If all stations connected, only a few
crosspoints in use
• Non-blocking

14
Space Division Switch

15
Multistage Switch
• Reduced number of crosspoints
• More than one path through network
—Increased reliability
• More complex control
• May be blocking

16
Three Stage Space Division Switch

17
Time Division Switching
• Modern digital systems rely on intelligent
control of space and time division
elements
• Use digital time division techniques to set
up and maintain virtual circuits
• Partition low speed bit stream into pieces
that share higher speed stream

18
Control Signaling Functions
• Audible communication with subscriber
• Transmission of dialed number
• Call can not be completed indication
• Call ended indication
• Signal to ring phone
• Billing info
• Equipment and trunk status info
• Diagnostic info
• Control of specialist equipment

19
Control Signal Sequence
• Both phones on hook
• Subscriber lifts receiver (off hook)
• End office switch signaled
• Switch responds with dial tone
• Caller dials number
• If target not busy, send ringer signal to target
subscriber
• Feedback to caller
— Ringing tone, engaged tone, unobtainable
• Target accepts call by lifting receiver
• Switch terminates ringing signal and ringing tone
• Switch establishes connection
• Connection release when Source subscriber hangs up

20
Switch to Switch Signaling
• Subscribers connected to different
switches
• Originating switch seizes interswitch trunk
• Send off hook signal on trunk, requesting
digit register at target switch (for address)
• Terminating switch sends off hook
followed by on hook (wink) to show
register ready
• Originating switch sends address

21
Location of Signaling
• Subscriber to network
—Depends on subscriber device and switch
• Within network
—Management of subscriber calls and network
—More complex

22
In Channel Signaling
• Use same channel for signaling control and call
— Requires no additional transmission facilities
• Inband
— Control signals have same electromagnetic properties
(frequency) as voice signal
— Can go anywhere a voice signal can
— Impossible to set up a call on a faulty speech path
• Out of band
— Voice signals do not use full 4kHz bandwidth
— Narrow signal band within 4kHz used for control
— Can be sent whether or not voice signals are present
— Need extra electronics
— Slower signal rate (narrow bandwidth)

23
Drawbacks of In Channel Signaling
• Limited transfer rate
• Delay between entering address (dialing)
and connection
• Overcome by use of common channel
signaling

24
Common Channel Signaling
• Control signals carried over paths independent of
voice channel
• One control signal channel can carry signals for
a number of subscriber channels
• Common control channel for these subscriber
lines
• Associated Mode
— Common channel closely tracks interswitch trunks
• Disassociated Mode
— Additional nodes (signal transfer points)
— Effectively two separate networks

25
Common
Channel
Signaling
Modes

26
Signaling System Number 7
• SS7
• Common channel signaling scheme
• ISDN
• Overall purpose to provide international
standardized common channel signaling
system
• Performs call management (setup,
maintenance, termination) and network
management functions
• Network is circuit switched, but control is
packet switched
27
Softswitch Architecture
• Latest trend in circuit-switching
technology
• General purpose computer running software to
make it a smart phone switch
• Lower cost, greater functionality
• Can packetize digitized voice data, allowing voice
over IP
• Performs call routing
• Separates call processing from hardware function
of switch

28
Traditional Circuit Switching

29
Softswitch

30
Circuit Switching Shortcomings
• Inefficient for data because of idle time
• Provides for transmission at constant rate
– must transmit and receive at same data
rate. Limits versatility

31
Packet Switching Basic Operation
• Data transmitted in small packets
—Typically 1000 octets (8 bit byte)
—Longer messages split into series of packets
—Each packet contains a portion of user data
plus some control info
• Control info
—Routing (addressing) info
• Packets are received, stored briefly
(buffered) and passed on to the next node
—Store and forward

32
Use of Packets

33
Advantages
• Line efficiency
— Single node to node link can be shared by many packets
over time
— Packets queued and transmitted as fast as possible
• Data rate conversion
— Each station connects to the local node at its own speed
— Nodes buffer data if required to equalize rates
• Packets are accepted even when network is busy
— Delivery may slow down
• Priorities can be used

34
Switching Technique
• Station breaks long message into packets
• Packets sent one at a time to the network
• Packets handled in two ways
—Datagram
—Virtual circuit

35
Datagram
• Each packet treated independently
• Packets can take any practical route
• Packets may arrive out of order
• Packets may go missing
• Up to receiver to re-order packets and
recover from missing packets

36
Datagram
Diagram

37
Virtual Circuit
• Preplanned route established before any
packets sent
• Call request and call accept packets
establish connection (handshake)
• Each packet contains a virtual circuit
identifier instead of destination address
• No routing decisions required for each
packet
• Clear request to drop circuit
• Not a dedicated path
38
Virtual
Circuit
Diagram

39
Virtual Circuits v Datagram
• Virtual circuits
—Network can provide sequencing and error
control
—Packets are forwarded more quickly
• No routing decisions to make
—Less reliable
• Loss of a node loses all circuits through that node
• Datagram
—No call setup phase
• Better if few packets
—More flexible
• Routing can be used to avoid congested parts of the
network

40
Circuit vs. Packet Switching
Circuit Switched Packet Switched
• Bandwidth • Bandwidth
dynamically
guaranteed
allocated on as-
• Circuit capacity not needed basis
reduced by other • May have concurrent
network traffic transmissions over
• Circuit costs physical channel
independent of • May have delays and
amount of data congestion
transmitted, • More cost-effective,
offer better
resulting in wasted performance
bandwidth
41
X.25
• Old ITU standard
• Interface between host and packet
switched network
• Almost universal on packet switched
networks and packet switching in ISDN
• Defines three layers
—Physical
—Link
—Packet

42
X.25 Use of Virtual Circuits

43
Virtual Circuit Service
• Logical connection between two stations
—External virtual circuit
• Specific preplanned route through network
—Internal virtual circuit
• Typically one to one relationship between
external and internal virtual circuits
• Can employ X.25 with datagram style network
• External virtual circuits require logical channel
—All data considered part of stream

44
Frame Relay
• Designed to be more efficient than X.25
• Developed before ATM
• Larger installed base than ATM
• ATM now of more interest on high speed
networks

45
Frame Relay
• Public WAN packet-switching protocol
• Provides LAN-LAN connectivity
• Relays frames across a network from
source to destination
• Connection-oriented protocol – must first
establish a connection before two nodes
can communicate

46
 LAN-LAN Connectivity
Prior to Frame Relay
• Conventional dial-up circuit switching
• Dedicated leased line using point-to-point
protocols or X.25 Packet Switching
• (Both have significant problems in today’s
technology)

47
Frame Relay Circuits
• Connection-oriented protocol
• Relies on permanent virtual circuit (PVC) –
provide non-dedicated connections
through a shared medium (bandwidth is
shared among multiple sites (simplex
lines)
• Can also support switched virtual circuit
(SVC)

48
Frame Relay Permanent Virtual Circuit

• Pre-determined link between source and

destination
• Bandwidth is shared among multiple sites,
not dedicated
• Bandwidth cost based on Committed
Information Rate (CIR)
• Frames encapsulate data contained in
layers 3-7

49
CIR
• If Leased line, a fixed amount of bandwidth is provided,
regardless of use.
• If CIR, frame relay provider guarantees a given
throughput (bps) during normal workloads - user
hedges bet and hopes for more
• CIR can be symmetric or asymmetric (as in ADSL)
• If CIR is too small, network becomes congested, and
frames may be dropped
• If CIR is too high, you are paying for excessive
bandwidth (think of the Sprint commercials)
• Service provider does not guarantee delivery above CIR

50
BURST
• A data transmission that is equal to, or
exceeds the CIR
• Committed Burst – Maximum amount of
data the provider guarantees to deliver
within a specified time period (CIR/time) –
In general, CIR should not exceed 70% of
port speed
• Excessive Burst – Maximum amount of
uncommitted data a provider will attempt
to deliver within a specified time period

51
Committed plus Excessive Burst

52
Switched Virtual Circuit
• Frame Relay also supports switched
virtual circuits (SVC)
• SVCs also support CIRs
• Circuits between source and destination
are established when needed (logical
dynamic, rather than logical permanent)
• Analogous to PSTN - paths change
between connections

53
PVC Advantages and
Disadvantages
 Widespread availability
 Less complex network design
 Less expensive equipment
• Permanent connections - always paying
for a certain amount of bandwidth,
regardless of use
• Every time a new connection is required, a
new permanent circuit must be
established

54
Frame Relay Basic Operation
• Packet switching – every frame carries
source and destination address
• Data link layer protocol, but does not
support flow control, error detection,
frame sequencing or ACK (all performed at
end nodes (routers))
—Since frame integrity performed by end nodes,
FR is fast and efficient
• Statistical multiplexing – multiple
subscribers share same backbone

55
Congestion Control and Management

• If no ACK within a given time period,

sending node assumes frame was
discarded
• Discarded frames must be
retransmitted, increasing network traffic
• Provider responsibilities
— Design networks to provide sufficient bandwidth
— Ensure links are error free
— Prevent any node from monopolizing the system
— Distribute resources in fair and equitable manner
• Refer to Lucent White Paper
http://www.lucent.com/livelink/090094038000
49af_White_paper.pdf
56
Advantages and Disadvantages
• Lost link by link error and flow control
—Increased reliability makes this less of a
problem
• Streamlined communications process
—Lower delay
—Higher throughput

57
Required Reading
• Stallings Chapter 10
• http://www.lucent.com/livelink/
09009403800049af_White_paper.pdf

58
Chapter 10 Review Questions
• Why is it useful to have more than one possible path
through a network for each pair of stations?
• Describe a simple switched network; describe a circuit
switched network
• What is a dedicated path?
• Describe the differences between blocking and non-
blocking circuit switching
• Describe how circuit switching is inefficient.
• Describe SS7.
• Describe packet switching. What are the advantages
of packet switching compared to circuit switching?
• Explain the difference between datagram and virtual
circuit operation.
• Continued on next page!
59
Chapter 10 Review Questions
(cont.)
• What is the significance of packet size in a packet-
switching network?
• What is the difference between inchannel and
common channel signaling? Which is preferred,
and why?
• Describe frame relay. What are the relative
advantages and disadvantages of frame relay?
• Compare and contrast PVC and SVC
• Explain the concept of the committed information
rate (CIR)
• Describe frame relay’s method of congestion
control.

60