Motherboard manual 8vm533m-rz_e

8VM533M-RZ /
8VM533M-RZ-C
Intel® Pentium® 4 Processor Motherboard

User's Manual
Rev. 1003
12ME-VM533MRZ-1003

Copyright
© 2004GIGABYTE TECHNOLOGYCO., LTD
Copyright by GIGA-BYTETECHNOLOGY CO.,LTD. ("GBT"). No part of this manual may be reproduced or transmitted in any from
without the expressed, written permission of GBT.
Trademarks
Third-party brands and names are the property of their respective owners.
Notice
Please do not remove any labels on motherboard, this may void the warranty of this motherboard.
Due to rapid change in technology, some of the specifications might be out of date before publication of this booklet.
The author assumes no responsibility for any errors or omissions that may appear in this document nor does the author make a
commitmentto update the informationcontained herein.

Mother Board
8VM533M-RZ
Motherboard
8VM533M-RZ
Feb. 20 ,2004
Feb. 20, 2004

Preparing Your Computer
Computer motherboards and expansion cards contain very delicate Integrated Circuit (IC) chips. To
protect them against damage from static electricity, you should follow some precautions whenever you
work on your computer.
1. Unplug your computer when working on the inside.
2. Use a grounded wrist strap before handling computer components. If you do not have one,
touch both of your hands to a safely grounded object or to a metal object, such as the power
supply case.
3. Hold components by the edges and try not touch the IC chips, leads or connectors, or other
components.
4. Place components on a grounded antistatic pad or on the bag that came with the components
whenever the components are separated from the system.
5. Ensure that the ATX power supply is switched off before you plug in or remove the ATX power
connector on the motherboard.

Installing the motherboard to the chassis
If the motherboard has mounting holes, but they don't line up with the holes on the base and there
are no slots to attach the spacers, do not become alarmed you can still attach the spacers to the
mounting holes. Just cut the bottom portion of the spacers (the spacer may be a little hard to cut off, so
be careful of your hands). In this way you can still attach the motherboard to the base without worrying
about short circuits. Sometimes you may need to use the plastic springs to isolate the screw from the
motherboard PCB surface, because the circuit wire may be near by the hole. Be careful, don't let the
screw contact any printed circuit write or parts on the PCB that are near the fixing hole, otherwise it
may damage the board or cause board malfunctioning.

Table of Contents
English

Chapter 1 Introduction ................................................................................................ 5
Features Summary ...........................................................................................................................5
8VM533M-RZ Series Motherboard Layout......................................................................................6
Block Diagram ..................................................................................................................................7
Hardware Installation Process .........................................................................................................8
Step 1: Install the Central Processing Unit (CPU) ..........................................................................8
Step 1-1: CPU Installation ................................................................................................. 9
Step 1-2: CPU Cooling Fan Installation ............................................................................ 9
Step 2: Install Memory Modules ....................................................................................................10
Step 3: Install AGP Card ............................................................................................................... 11
Step 4: Install I/O Peripherals Cables ........................................................................................... 11
Step 4-1: I/O Back Panel Introduction ............................................................................. 11
Step 4-2: Connectors Introduction ................................................................................... 12

Chapter 2 BIOS Setup ............................................................................................. 19
The Main Menu (For example: BIOS Ver. : F4a) .........................................................................19
Standard CMOS Features .............................................................................................................21
Advanced BIOS Features .............................................................................................................23
IntegratedPeripherals .....................................................................................................................24
Power Management Setup .............................................................................................................26
PnP/PCI Configurations .................................................................................................................27
PC Health Status ............................................................................................................................28
Frequency/Voltage Control .............................................................................................................29
Load Fail-Safe Defaults ...................................................................................................................30
Load Optimized Defaults .................................................................................................................30
Set Supervisor/User Password .....................................................................................................31
Save & Exit Setup .........................................................................................................................32
Exit Without Saving ........................................................................................................................32

Chapter 3 Install Drivers ........................................................................................... 33

8VM533M-RZ Series Motherboard -4-

Chapter 1 Introduction

English
Features Summary
CPU — Socket 478 for Intel® Pentium ® 4 (Northwood) with HT Technology
— Intel® Pentium ® 4 533/400MHz FSB
— 2nd cache depends on CPU
Chipset — North Bridge: VIA P4M266A/P4M533
— South Bridge: VIA VT8235/VT8237R
Memory — 2 184-pin DDR DIMM sockets, supports up to 2GB DRAM (Max)
— Supports DDR266/DDR200 DIMM
— Supports only 2.5V DDR SDRAM
Slots — 1 AGP slot 4X (1.5V) device support
— 3 PCI slots support 33M Hz & PCI 2.2 compliant
On-Board IDE — 2 IDE controller provide IDE HDD/CD-ROM(IDE1, IDE2) with PIO, Bus
Master (Ultra DMA33/ATA66/ATA100/ATA133) operation modes
— Can connect up to 4 IDE devices
On-Board Floppy — 1 Floppy port supports 2 FDD with 360K, 720K,1.2M, 1.44M and 2.88M bytes
On-Board Peripherals — 1 Parallel port supports Norm al/EPP/ECP mode
— 1 Serial port (COMA), 1 VGA port, COMB onboard
— 6 USB 2.0/1.1 ports (4 x Rear, 2 x Front by cable)
— 1 Front Audio connector
— 1 PS/2 Keyboard
— 1 PS/2 Mouse
On-Board LAN * — Builit-in VIA 6103 chipset *
— 1 RJ45 port *
On-Board Sound — VIA VT1616 CODEC
— Support 2/6 channel
— Line Out / Line In / Mic In
— CD In
BIOS — Licensed AWARD BIOS
— Supports Q-Flash™
I/O Control — ITE8705
Hardware M onitor — CPU Fan Revolution detect
— CPU Fan Fail Warning
— CPU tem perature detect
— System Voltage Detect
Additional Features — Supports @BIOS™
— Supports EasyTune 4™
Form Factor — Micro ATX size form factor, 24.5cm x 20.8cm

"*" For 8VM533M-RZ only.

-5- Introduction

8VM533M-RZ Series Motherboard Layout
English

20.8 cm

#
KB_MS
FDD

CPU_FAN
ATX
COMA
LPT

SOC KET 478
VGA

8VM533M-RZ
IDE1
R_USB A TX_12V

IDE2

24.5 cm
LAN *
USB

AUDIO
V T6103 * VIA P4M 266A /P4M 533
DDR1
DDR2

F_AU DIO BAT
AGP

PCI1
CODEC

V I A V T82 35/
PCI2 V T8237R

BIOS
PCI3
I TE 8705
F_U SB1 F_PANEL
CD_I N COMB

PWR_LE D

"#" For8VM533M-RZ-C only.


Block Diagram

English
Pentium 4 CPUCLK+/- (100/133MHz)
Socket 478
CPU

AGP 4X System Bus
VGA Port 533/400MHz 200/266MHz

DDR
VIA
P4M266A/P4M533 MCHCLK (100/133MHz)
AGPCLK AGPCLK66 MHz
66MHz
66MHz V_Link

33 MHz
3 PCI 14.318 MHz
RJ45 *

VT6103* 48 MHz

BIOS
MII

PCI BUS 33MHz VIA LPC BUS
VT8235/VT8237R Floppy
IT8705
LPT Port
AC97 Link

PS/2 KB/Mouse
24 MHz
33 MHz
6 Channel 6 USB ATA33/66/ COM A/COMB
CODEC Ports 100/133
IDE Channels
PCICLK
(33MHz)
LINE-OUT
MIC
LINE-IN

PCICLK (33MHz) MCHCLK (100/133MHz)
USBCLK (48MHz) CLK
CPUCLK+/- (100/133MHz)
14.318 MHz GEN AGPCLK (66MHz)
33 MHz V_Link (66MHz)


-7- Introduction

Hardware Installation Process
English

To set up your computer, you must complete the following steps:
Step 1- Install the Central Processing Unit (CPU)
Step 2- Install mem ory modules
Step 3- Install expansion cards
Step 4- Connect ribbon cables, cabinet wires, and power supply

Step 4 Step 1 Step 2

Step 4
Step 4

Step 3

Step 1: Install the Central Processing Unit (CPU)
Before installing the processor, adhere to the following warning:
1. Please m ake sure the CPU type is supported by the m otherboard.
2. The processor will overheat without the heatsink and/or fan, resulting in perm anent
irreparable damage.
3. If you do not match the CPU socket Pin 1 and CPU cut edge well, it will cause im proper
installation. Please change the insert orientation.
4. Apply thermal grease between the processor and cooling fan.
5. Never run the processor without the heatsink properly and firmly attached. Perm anent
damage will result.
6. Please set the CPU host frequency in accordance with your processor's specifications.
We don't recomm end you to set the system bus frequency over the CPU's specification
because these specific bus frequencies are not the standard specifications for CPU,
chipset and most of the peripherals. Whether your system can run under these specific
bus frequencies properly will depend on your hardware configurations, including CPU,
Memory, Cards… etc.
HT functionality requirement content :
Enabling the functionality of Hyper-Threading Technology for your com puter system
requires all of the following platform components:
- CPU: An Intel® Pentium 4 Processor with HT Technology
- Chipset: An VIA Chipset that supports HT Technology
- BIOS: A BIOS that supports HT Technology and has it enabled
- OS: An operation system that has optim izations for HT Technology


Step 1-1: CPU Installation

English
Figure 1.
Socket
Pull the rod to the 90-degree directly.
Actuation
Lever

Figure 2.
Locate Pin 1 in the socket and look for a (golden) cut edge on the
CPU upper corner. Insert the CPU into the socket. (Do not force the
CPU into the socket.) Then m ove the socket lever to the locked
position while holding pressure on the center of the CPU.

Step 1-2: CPU Cooling Fan Installation
Figure 1.
Apply the therm al tape(or grease) to provide better heat conduction
between your CPU and cooling fan.

Figure 2.
Fasten the cooling fan supporting-base onto the CPU socket on the
motherboard.

Figure 3.
Make sure the CPU fan is plugged to the CPU fan connector, than
install complete.

-9- Hardware Installation Process

Step 2: Install Memory Modules
English

Before installing the m emory modules, adhere to the following warning:
1. Please note that the DIMM module can only fit in one direction due to the one notch.
Wrong orientation will cause im proper installation. Please change the insert orientation.

The motherboard has 2 dual inline memory m odule (DIM M) sockets. The BIOS will automatically
detects memory type and size. To install the memory module, just push it vertically into the DIMM
socket. The DIM M module can only fit in one direction due to the notch. M emory size can vary between
sockets.

Notch

DDR

1. The DIMM socket has a notch, so the DIMM
memory module can only fit in one direction.

2. Insert the DIMM mem ory module vertically into
the DIM M socket. Then push it down.

3. Close the plastic clip at both edges of the DIMM
sockets to lock the DIM M m odule.
Reverse the installation steps when you wish to
rem ove the DIM M module.

8VM533M-RZ Series Motherboard - 10 -

Step 3: Install AGP Card

English
1. Read the relateAGP card's instruction document before install the AGP card into the computer.
2. If your AGP card has "AGP 4X(1.5V) notch" (show below), please make sure your AGP card is AGP
4X(1.5V).

3. Please carefully pull out the small white- drawable bar at the end of the AGP slot when you try to
install/ Uninstall the AGP card. Please align the AGP card to the onboard AGP slot and press firm ly
down on the slot .M ake sure your AGP card is locked by the sm all white- drawable bar.

Step 4: Install I/O Peripherals Cables
Step 4-1: I/O Back Panel Introduction
v z *
u |

y
w x }
{
~

u PS/2 Keyboard and PS/2 Mouse connector
This connector supports standard PS/2 keyboard and PS/2 m ouse.
v Parallel port (LPT)
Device like printer can be connected to Parallel port.
w Serial port (COMA)
Mouse and modem etc. can be connected to Serial port.
x VGA port
Monitor can be connected to VGA port.
y/{ USB port
Before you connect your device(s) into USB connector(s), please make sure your device(s)
such as USB keyboard, mouse, scanner, zip, speaker...etc. Have a standard USB interface.
Also m ake sure your OS supports USB controller. If your OS does not support USB controller,
please contact OS vendor for possible patch or driver upgrade. For more information please
contact your OS or device(s) vendors.


- 11 - Hardware Installation Process

z LAN port *
English

LAN is fast Ethernet with 10/100M bps speed.
| Line In jack
Devices like CD-ROM , walkm an etc. can be connect to Line In jack.
} Line Out jack
Connect the stereo speakers or earphone to this connector.
~ MIC In jack
Microphone can be connect to MIC In jack.
After installation of the audio driver, you are able to use 2/4/6-channel audio feature by software
selection. You can connect "Front speaker" to "Line Out" jack, Connect "Rear speaker" to
"Line In" jack and connect "Center/Subwoofer" to "MIC In" jack.

Step 4-2: Connectors Introduction
1 3 2

4

5

9
6

12
7

10 11 8

1) ATX_12V 7) F_PANEL
2) ATX 8) PWR_LED
3) CPU_FAN 9) F_AUDIO
4) FDD 10) CD_IN
5) IDE1 / IDE2 11) F_USB1
6) BAT 12) COMB



1) ATX_12V (+12V Power Connector)

English
This connector (ATX_12V) supplies the CPU operation voltage (Vcore).
If this "ATX_12V connector" is not connected, system cannot boot.

4 2 Pin No. Definition
1 GND
2 GND
3 +12V
3 1
4 +12V

2) ATX (ATX Power)
AC power cord should only be connected to your power supply unit after ATX power cable and
other related devices are firmly connected to the mainboard.

Pin No. Definition Pin No. Definition
11 1
1 3.3V 11 3.3V
2 3.3V 12 -12V
3 GND 13 GND
4 VCC 14 PS_ON(softon/off)
5 GND 15 GND
6 VCC 16 GND
7 GND 17 GND
20 8 PowerGood 18 -5V
10
9 5V SB (stand by +5V) 19 VCC
10 +12V 20 VCC

3) CPU_FAN (CPU Fan Connector)
Please note, a proper installation of the CPU cooler is essential to prevent the CPU from running
under abnormal condition or damaged by overheating. The CPU fan connector supports Max.
current up to 600 m A.

Pin No. Definition
1 GND
1 2 +12V
3 Sense


4) FDD (Floppy Connector)
English

Please connect the floppy drive ribbon cables to FDD. It supports 360K, 1.2M, 720K, 1.44M and
2.88M bytes floppy disk types.
The red stripe of the ribbon cable must be the sam e side with the Pin1.

34 33

2 1

5) IDE1 / IDE2 (IDE1 / IDE2 Connector)
Im portant Notice: Please connect first hard disk to IDE1 and connect CD-ROM to IDE2. The red
stripe of the ribbon cable must be the sam e side with the Pin1.

40 39

IDE2 IDE1

2 1

6) BAT (BATTERY)

+

CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the
manufacturer.
Dispose of used batteries according to the manufacturer's instructions.
If you want to erase CMOS...
1. Turn OFF the computerand unplug the power cord.
2. Remove the battery, wait for 30 second.
3. Re-install the battery.
4. Plug the power cord and turn ON the computer.

7) F_PANEL (2 x 10 pins Connector)

English
Please connect the power LED, PC speaker, reset switch and power switch etc of your chassisfront
panel to the F_PANEL connector according to the pin assignment below.
Soft Po we r
Con nector
Messa ge L ED / Sp eaker Co nne ctor
Po we r /
Sl ee p LED

MSG+

PW+

SPEAK+

SPEAK-
MSG-

PW-
1

1

1

19 20
1 2

1
1

RES+
HD-

NC
HD+

RES-
IDE H a rd D i sk Acti ve LED

R eset Swi tch

HD (IDE Hard Disk Active LED) Pin 1: LED anode(+)
Pin 2: LED cathode(-)
SPK(Speaker Connector) Pin 1: VCC(+)
Pin 2- Pin 3: NC
Pin 4: Data(-)
RES (Reset Switch) Open:Normal Operation
Close: Reset Hardware System
PW (Soft Power Connector) Open:Normal Operation
Close: Power On/Off
MSG (Message LED/ Power/ Sleep LED) Pin 1: LED anode(+)
Pin 2: LED cathode(-)
NC NC

8) PWR_LED
PWR_LED is connect with the system power indicator to indicate whether the system is on/off.
It will blink when the system enters suspend mode. If you use dual color LED, power LED will turn
to another color.

Pin No. Definition
1 MPD+
1
2 MPD-
3 MPD-


9) F_AUDIO (Front Audio Connector)
English

In order to utilize the front audio header, your chassis must have front audio connector. Also
please make sure the pin assigm ent on the cable is the same as the pin assigm ent on the MB
header. To find out if the chassis you are buying support front audio connector, please contact
your dealer. Please note, you can have the alternative of using front audio connector or of using
rear audio connector to play sound.
Pin No. Definition
1 MIC
2 GND
3 REF
10 9 4 Power
5 Front Audio (R)
2 1 6 Rear Audio (R)
7 Reserved
8 No Pin
9 Front Audio (L)
10 Rear Audio (L)
10) CD_IN (CD In Connector)
Connect CD-ROM or DVD-ROM audio out to the connector.

Pin No. Definition
1 CD-L
2 GND
1
3 GND
4 CD-R

11) F_USB1 (Front USB Connector)
Be careful with the polarity of the front USB connector. Check the pin assignment carefully while
you connect the front USB cable, incorrect connection between the cable and connector will m ake
the device unable to work or even damage it. For optional front USB cable, please contact your
local dealer.
Pin No. Definition
1 Power
2 Power
3 USB DX-
2 10 4 USB Dy-
5 USB DX+
6 USB Dy+
1 9
7 GND
8 GND
9 No Pin
10 NC


12) COMB (COM B Connector)

English
Be careful with the polarity of the COMB connector. Check the pin assignm ent while you connect
the COMB cable. Please contact your nearest dealer for optional COMB cable.

Pin No. Definition
1 NDCDB-
2 NSINB
3 NSOUTB
2 10
4 NDTRB-
5 GND
1 9 6 NDSRB-
7 NRTSB-
8 NCTSB-
9 NRIB-
10 No Pin


English


Chapter 2 BIOS Setup

English
BIOS Setup is an ov erv iew of the BIOS Setup Program. The program that allow s users to modify the
basic sy stem configuration. This ty pe of information is stored in battery -backed CM OS RAM so that it
retains the Setup information w hen the pow er is turned off.
ENTERING SETUP
Pow ering ON the computer and pressing <Del> immediately w ill allow y ou to enter Setup. If y ou require
m ore adv anced BIOS s ettings , pleas e go to "Adv anc ed BIOS" s etting m enu. To enter
Adv anced BIOS s etting menu, press "Ctrl+F1" key on the BIOS sc reen.
CONTRO L KEYS
< >< >< >< > Mov e to select item
<Enter> Select Item
<Esc> Main Menu - Quit and not sav e c hanges into CMOS Status Page Setup Menu
and Option Page Setup Menu - Ex it current page and return to Main Menu
<+/PgUp> Increase the numeric v alue or make changes
<-/PgDn> Decrease the numeric v alue or make changes
<F1> General help, only for Status Page Setup Menu and Option Page Setup Menu
<F2> Item Help
<F5> Restore the prev ious CMOS v alue from CMOS, only for Option Page Setup Menu
<F6> Load the file-safe default CMOS v alue from BIOS default table
<F7> Load the Optim ized Defaults
<F8> Q-Flash utility
<F9> Sy stem Inform ation
<F10> Sav e all the C MOS changes, only for Main Menu

Main Menu
The on-line description of the highlighted setup function is display ed at the bottom of the sc reen.
Status Page Setup Menu / Opti on Page Setup Menu
Press F1 to pop up a sm all help w indow that describes the appropriate key s to use and the pos sible
selec tions for the highlighted item. To ex it the Help Window press <Esc>.

The Main Menu (For example: BIOS Ver. : F4a)
Once y ou enter Aw ard BIOS C MOS Setup Utility , the Main Menu (as figure below ) w ill appear on the
screen. T he Main Menu allow s y ou to select from eight setup func tions and tw o ex it choices. Use
arrow key s to s elect among the items and press <Enter> to accept or enter the sub-menu.
CMOS Setup Ut ility-Co pyright (C) 1984 -2003 Aw ard Soft ware

} Stan dard CM OS Feat ures Load Fail-Sa fe Defa ults
} Adva nced BI OS Feat ures Load Optimiz ed Defa ults
} Inte grated Periphe rals Set Supervis or Pass word
} Powe r Manag ement S etup Set U ser Pass word
} PnP/ PCI Con figurat ions Save & Exit S etup
} PC H ealth St atus Exit Without S aving
} Frequ ency/Vol tage Con trol

ESC: Quit higf: Selec t Item
F8: Q- Flash F10: Save & Exit S etup
Time, Date, Har d Disk Ty pe...

- 19 - BIOS Setup

If you can't find the setting you want, please press "Ctrl+F1" to search the advanced
English

option hidden.

• Standard CMOS Features
This setup page includes all the items in s tandard c ompatible BIOS.
• Advanced BIOS Features
This setup page includes all the items of Aw ard special enhanced features.
• Integrated Peripherals
This setup page includes all onboard peripherals.
• Power Management Setup
This setup page includes all the items of Green func tion features.
• PnP/PCI Configuration
This setup page includes all the configurations of PCI & PnP ISA resources.
• PC Health Status
This setup page is the Sy stem auto detect Temperature, v oltage, fan, s peed.
• Frequency/Voltage Control
This setup page is control CPU clock and frequency ratio.
• Load Fail-Safe Defaults
Fail-Safe Defaults indicates the v alue of the sy s tem parameters w hich the sy stem w ould be in safe
configuration.
• Load O ptimized Defaults
Optim ized Defaults indicates the v alue of the sy stem parameters w hich the sy stem w ould be in
best performance configuration.
• Set Supervisor Password
Change, set, or disable passw ord. It allow s y ou to limit acces s to the s y stem and Setup, or just
to Setup.
• Set User Password
Change, set, or disable passw ord. It allow s y ou to limit access to the sy stem.
• Save & Exit S etup
Sav e CMOS v alue settings to CMOS and ex it s etup.
• Exit Without S aving
Abandon all CM OS v alue changes and ex it s etup.


Standard CMOS Features

English
Stan dard CM OS Feat ures
Date (mm:dd :yy) Fri, Jan 9 2004 Item Help
Time (hh:mm :ss) 22:3 1:24 Menu L evel}
Chan ge the day, mo nth,
} IDE P rimary M aster [No ne] year
} IDE P rimary S lave [No ne]
} IDE S econdary M aster [No ne] <We ek>
} IDE S econdary Slave [No ne] Sun. t o Sat.

Driv e A [1.44M, 3.5"] <Mon th>
Driv e B [No ne] Jan. t o Dec.
Floppy 3 Mode Su pport [Disa bled]
<Day>
Halt On [All, But Keyb oard] 1 to 31 (or ma ximum
allowe d in the m onth)
Base M emory 640K
Exte nded Me mory 127M <Ye ar>
Total Memory 128M 1999 t o 2098
higf: M ove Enter: Select +/-/ PU/PD: V alue F10: Save ESC: Exit F1: General Help
F5: P revious V alues F6: Fa il-Safe De fault F7: Optimiz ed Defa ults

Date
The date format is <w eek>, <month>, <day >, <y ear>.
Week The w eek, from Sun to Sat, determined by the BIOS and is display only
Month The m onth, Jan. Through Dec.
Day The day , from 1 to 31 (or the max imum allow ed in the m onth)
Year The y ear, from 1999 through 2098
Time
The times format in <hour> <m inute> <second>. The time is c alc ulated bas e on the 24-hour
military -time clock. F or ex ample, 1 p.m. is 13:00:00.
IDE Primary Master, Slave / IDE Secondary Master, Slave
The category identifies the ty pes of hard disk from driv e C to F that has been installed in the
computer. There are tw o ty pes: auto ty pe, and manual ty pe. Manual ty pe is user-definable; Auto ty pe
w hich w ill autom atically detect HDD ty pe.
Note that the spec ifications of y our driv e must matc h w ith the driv e table. The hard disk w ill not w ork
properly if y ou enter improper information for this category .
If y ou select User Ty pe, related information will be asked to enter to the follow ing items. Enter the information
directly from the k ey board and press <Enter>. Such information should be prov ided in the doc umenta-
tion form y our hard disk v endor or the sy stem manufacturer.
Cy linder Number of cy linders
Head Number of heads
Prec omp Write precomp
Landing Zone Landing zone
Sec tor Number of sec tors
If a hard disk has not been installed, selec t NONE and press <Enter>.

- 21 - BIOS Setup

Drive A / Dri ve B
English

The category identifies the ty pes of floppy disk driv e A or driv e B that has been installed in the
computer.
None No floppy driv e installed
360K, 5.25" 5.25 inch PC-ty pe standard driv e; 360K by te capacity .
1.2M, 5.25" 5.25 inch AT-ty pe high-density driv e; 1.2M by te capacity
(3.5 inch w hen 3 Mode is Enabled).
720K, 3.5" 3.5 inch double-sided driv e; 720K by te capacity
1.44M, 3.5" 3.5 inch double-sided driv e; 1.44M by te capacity .
2.88M, 3.5" 3.5 inch double-sided driv e; 2.88M by te capacity .
Floppy 3 Mode Support (for Japan Area)
Disabled Normal Floppy Driv e. (Default v alue)
Driv e A Driv e A is 3 mode Floppy Driv e.
Driv e B Driv e B is 3 mode Floppy Driv e.
Both Driv e A & B are 3 mode Floppy Driv es.
Halt on
The c ategory determines w hether the computer w ill stop if an error is detected during pow er up.
No Errors The sy stem boot w ill not s top for any error that may be detected and y ou
w ill be prompted.
All Errors Whenev er the BIOS detects a non-fatal error the s y stem w ill be stopped.
All, But Key board The s y stem boot w ill not stop for a key board error; it w ill stop for all other
errors . (Default v alue)
All, But Disk ette The sy stem boot w ill not stop for a disk error; it w ill stop for all other errors.
All, But Disk /Key The sy stem boot w ill not stop for a key board or disk error; it w ill stop for all
other errors.
Memory
The c ategory is display -only w hich is determined by POST (Pow er On Self Test) of the BIOS.
Base Memory
The POST of the BIOS w ill determine the amount of base (or conv entional) memory ins talled
in the sy stem.
The v alue of the base memory is ty pic ally 512K for sy stems w ith 512K memory installed on
the motherboard, or 640K for sy stems w ith 640K or more memory installed on the motherboard.
Extended Memory
The BIOS determines how much ex tended memory is present during the POST.
This is the am ount of memory located abov e 1 MB in the CPU 's memory address map.


Advanced BIOS Features

English
Adva nced BI OS Feat ures
Firs t Boot D evice [Flo ppy] Item Help
Seco nd Boot D evice [HDD -0] Menu L evel}
Thir d Boot D evice [CDR OM] Selec t Boot D evice
Pas sword C heck [Set up] prio rity
#
CPU H yper-Threa ding [Enab led]
[Flo ppy]
Boot from fl oppy

[LS1 20]
Boot from L S120

[HDD -0]
Boot from Firs t HDD

[HDD -1]
Boot from Secon d HDD


" # " Sy stem w ill detect automatic ally and s how up w hen y ou ins tall the Intel® Pentium ® 4
proc essor w ith HT Technology.

First / Second / Third Boot Device
Floppy Selec t y our boot dev ic e priority by Floppy .
LS120 Selec t y our boot dev ice priority by LS120.
HDD-0~3 Selec t y our boot dev ic e priority by HDD-0~3.
SCSI Select y our boot dev ice priority by SCSI.
CDROM Selec t y our boot dev ice priority by C DROM.
ZIP Selec t y our boot dev ice priority by ZIP.
USB-FDD Selec t y our boot dev ic e priority by USB-FDD.
USB-ZIP Selec t y our boot dev ic e priority by USB-ZIP.
USB-C DROM Selec t y our boot dev ice priority by USB-C DROM.
USB-HDD Selec t y our boot dev ic e priority by USB-HDD.
LAN Selec t y our boot dev ice priority by LAN.
Disabled Selec t y our boot dev ice priority by Disabled.
Password Check
Sy s tem The sy stem can not boot and can not acc ess to Setup page w ill be denied if the
correct passw ord is not entered at the prompt.
Setup The sy stem w ill boot, but access to Setup w ill be denied if the correct passw ord
is not entered at the prompt. (Default v alue)
CPU Hyper-Threading
Enabled Enables CPU Hy per Threading Feature. Please note that this feature is only w orking
for operating sy stem w ith multi processors mode supported. (Default value)
Disabled Disables CPU Hy per Threading.

- 23 - BIOS Setup

Integrated Peripherals
English

Inte grated Periphe rals
OnChi p IDE Cha nnel0 [Enab led] Item Help
OnChi p IDE Cha nnel1 [Enab led] Menu L evel}
AC97 Audio [Au to]
VIA o nboard L AN * [Enab led] [Au to]
USB 1 .1 Contr oller [Enab led] Auto -detect IDE
USB 2 .0 Contr oller [Enab led] cable type
USB K eyboard Su pport [Disa bled]
USB M ouse Sup port [Disa bled] [ATA 66/100/ 133]
Onboar d Serial P ort 1 [3F8/ IRQ4] Set C onductor cable
Onboar d Serial P ort 2 [2F8/ IRQ3] to AT A66/100/1 33(80
Onboar d Parallel Port [378/ IRQ7] -pi ns)
Paral lel Port Mode [SPP]
[ATA 33]
Set C onductor cable
to AT A33(40-p ins)


OnChi p IDE Channel0
When enabled, allow s y ou to use the onboard primary PCI IDE. If a hard disk controller card is
used, set at Dis abled.
Enabled Enable onboard 1st channel IDE port. (Default v alue)
Disabled Disable onboard 1st channel IDE port.
OnChi p IDE Channel1
When enabled, allow s y ou to use the onboard secondary PCI IDE. If a hard disk controller card is
used, set at Dis abled.
Enabled Enable onboard 2nd channel IDE port. (Default v alue)
Disabled Disable onboard 2nd channel IDE port.
AC97 Audio
Auto Enable onboard AC'97 audio function. (Default v alue)
Disabled Disable this function.
VIA onboard LAN *
Enable Enable onboard LAN function.(Default v alue)
Disable Disable onboard LAN func tion.
USB 1.1 Controller
Disable this option if y ou are not using the onboard USB feature.
Enabled Enable USB1.1 Controller. (Default v alue)
Disabled Disable USB1. 1 Controller.
USB 2.0 Controller
Disable this option if y ou are not using the onboard U SB 2.0 feature.
Enabled Enable USB 2. 0 Controller. (Default v alue)
Disabled Disable USB 2. 0 Controller.



USB Keyboard Support

English
Enabled Enable USB key board support.
Disabled Disable USB key board support. (Default v alue)
USB Mouse Support
Enabled Enable USB mouse support.
Disabled Disable USB m ouse support. (Default v alue)
Onboard Serial P ort 1
Auto BIOS w ill autom atically s etup the port 1 address.
3F8/ IRQ4 Enable onboard Serial port 1 and address is 3F8. (Default v alue)
2F8/ IRQ3 Enable onboard Serial port 1 and address is 2F8.
3E8/ IRQ4 Enable onboard Serial port 1 and address is 3E8.
Disabled Disable onboard Serial port 1.
Onboard Serial P ort 2
Auto BIOS w ill autom atically s etup the port 2 address.
3F8/ IRQ4 Enable onboard Serial port 2 and address is 3F8.
2F8/ IRQ3 Enable onboard Serial port 2 and address is 2F8. (Default v alue)
Disabled Disable onboard Serial port 2.
Onboard Parallel port
378/ IRQ7 Enable onboard LPT port and address is 378/IRQ7. (Default v alue)
278/ IRQ5 Enable onboard LPT port and address is 278/ IRQ5.
Disabled Disable onboard LPT port.
3BC/ IRQ7 Enable onboard LPT port and address is 3BC/ IRQ7.
Paral lel Port Mode
SPP Using Parallel port as Standard Parallel Port. (Default v alue)
EPP Using Parallel port as Enhanced Parallel Port.
ECP Using Parallel port as Ex tended Capabilities Port.
ECP+EPP Using Parallel port as ECP & EPP mode.

- 25 - BIOS Setup

Power Management Setup
English

Powe r Manag ement S etup
ACPI Suspend Type [S1(P OS)] Item Help
x USB D evice Wa ke-Up Fr om S3 Disa bled Menu L evel}
Soft- Off by PWR -BTTN [Instan t-Off] [S1]
AC B ack Func tion [Soft -Off] Set s uspend ty pe to
Keybo ard Powe r On [Disa bled] Powe r On Su spend u nder
Mous e Powe r On [Disa bled] ACPI OS
PME E vent Wak e Up [Enab led]
Resu me by A larm [Disa bled] [S3]
x Date ( of Month) Alarm Ever yday Set s uspend ty pe to
x Time ( hh:mm:ss) Alarm 0 : 0 : 0 Suspe nd to RAM under
ACPI OS


ACPI Suspend Type
S1(POS) Set ACPI suspend ty pe to S1. (Default v alue)
S3(STR) Set ACPI suspend ty pe to S3.
USB Device Wakeup From S3(When ACPI Suspend Type is set [S3/STR])
USB dev ice w ak eup From S3 can be set w hen ACPI standby state set to S3/STR.
Enabled USB Dev ice can w akeup s y stem from S3.
Disabled USB Dev ice can't w akeup sy stem from S3. (Default v alue)
Soft-off by PWR-BTTN
Instant-off Press pow er button then Pow er off instantly . (Default v alue)
Delay 4 Sec. Press pow er button 4 sec to Pow er off. Enter suspend if button is pressed
less than 4 sec.
AC Back Function
Soft-Off Alw ay s in Off state w hen AC back. (Default v alue)
Mem ory Sy stem pow er on depends on the status before AC lost.
Full-On Alw ay s pow er on the sy stem w hen AC back.
Keyboard Power On
This feature allow s y ou to set the method for pow ering-on the sy stem.
The option "Pass w ord" allow s y ou to set up to 8 alphanumeric characters to pow er-on the sy stem.
The option "Key board 98" allow s y ou to us e the standard key board 98 to pow er on the sy stem.
Pass w ord Enter from 1 to 8 charac ters to set the key board pow er on pass w ord.
Disabled Disabled this function. (Default v alue)
Key board 98 If y our key board hav e "POWER Key " button, y ou can press the k ey to
pow er on y our sy stem.
Mouse P ower On
Disabled Can't Pow er on sy stem by Mouse Ev ent. (Default v alue)
Enabled Can Pow er on sy stem by Mouse Ev ent.


PME Event Wake Up

English
When set at Enabled, any PCI-PM ev ent aw akes the sy stem from a PCI-PM controlled
state.
This feature requires an ATX pow er supply that prov ides at least 1A on the +5VSB lead.
Disabled Disable this function.
Enabled Enable PME as w ake up ev ent. (Default v alue)
Resume by Alarm
You c an set "Resume by Alarm" item to enabled and key in Data/ time to pow er on sy stem.
Disabled Disable this function. (Default Value)
Enabled Enable alarm function to POWER ON sy stem.
If RTC Alarm Lead To Pow er On is Enabled.
Date (of Month) Alarm : Ev ery day , 1~31
Time (hh: mm: ss) Alarm : (0~23) : (0~59) : (0~59)

PnP/PCI Configurations
PnP/ PCI Con figurat ions
PCI 1 IRQ Assig nment [Au to] Item Help
PCI 2 IRQ Assig nment [Au to] Menu L evel}
PCI 3 IRQ Assig nment [Au to]
Devic e(s) using this
INT:

Disp lay Cn trlr
-Bus 1 Dev 0 F unc 0


PCI 1 IRQ Assignment
Auto Auto assign IRQ to PC I 1. (Default v alue)
3,4, 5,7,9,10,11,12,14,15 Set IRQ 3,4,5,7,9,10, 11,12,14,15 to PCI 1.
3,4, 5,7,9,10,11,12,14,15 Set IRQ 3,4,5,7,9,10, 11,12,14,15 to PCI 2.
3,4, 5,7,9,10,11,12,14,15 Set IRQ 3,4,5,7,9,10, 11,12,14,15 to PCI 3.

- 27 - BIOS Setup

PC Health Status
English

PC H ealth St atus
Vcore 1.54V Item Help
DDR 25V 2.5 44V Menu L evel}
+3.3V 3.3 60V
+12V 11. 92V Don' t reset case
Curr ent CPU Tempera ture 45° C open s tatus
Curren t CPU FAN Speed 4440 RPM
CPU F AN Fail Wa rning [Disa bled] Clea r case open
statu s at next boot


Current Voltage (V) Vcore / DDR25V / +3.3V / +12V
Detec t sy stem' s v oltage status automatic ally .
Current CPU Temperature
Detec t CPU tem perature automatic ally .
Current CPU FAN Speed (RPM)
Detec t CPU Fan speed status automatic ally .
CPU FAN Fail Warning
Disabled Fan w arning function disable. (Default v alue)
Enabled Fan w arning function enable.


Frequency/Voltage Control

English
Frequ ency/Vol tage Con trol
CPU Clock R atio [15X] Item Help
Auto Detect PCI/DIMM Clk [Enab led] Menu L evel}
Spre ad Spec trum [Enab led]
CPU Host Cl ock Con trol [Disa bled]
ø CPU C lock 100


ø This item w ill be av ailable w hen "CPU Host Clock Control" is set to Enabled.

CPU Clock Ratio
This option w ill not be show n or not be av ailable if y ou are using a CPU w ith the locked ratio.
15X~21X It depends on C PU Clock R atio.
This setup option w ill automatically as sign by C PU detec tion.
For C -Stepping P4: 8X,10X~24X default: 15X
For N orthw ood C PU: 12X~24X default: 16X
The option w ill display "Locked" and read only if the CPU ratio is not changeable.
Auto Detect PCI/DI MM Clk
Disabled Disable auto detect PCI/DIMM Clk.
Enabled Enable auto detect PCI/DIMM Clk. (Default v alue)
Spread S pectrum
Disabled Disable spread spectrum.
Enabled Enable spread s pectrum. (Default v alue)
CPU Host Clock Control
Note: If sy stem hangs up before enter CMOS setup utility , w ait for 20 s ec for times out reboot.
When time out occur, sy s tem w ill reset and run at CPU default Host cloc k at nex t boot.
Disabled Disable CPU Host Clock C ontrol. (Default v alue)
Enabled Enable CPU Host Clock Control.
CPU Clock
Incorrect using it may c ause y our sy stem broken. For pow er End-User use only !
100 Set CPU Clock to 100MHz~132MHz.
133 Set CPU Clock to 133MHz~165MHz.

- 29 - BIOS Setup

Load Fail-Safe Defaults
English


} PnP/ PCI Con figurat ions Load Fail-Sa fe Defau lts (Y/N )? N S etup
Save & Exit

Loa d Fail-S afe Defa ults

Fail-Safe defaults contain the m ost appropriate v alues of the s y stem parameters that allow minimum
sy stem perform ance.

Load Optimized Defaults

} PnP/ PCI Con figurat ions Load Optimiz ed Defau lts (Y/N )? N S etup
Save & Exit

Load Optimiz ed Defa ults

Selecting this field loads the factory defaults for BIOS and Chipset Features w hich the sy stem automatically
detects.


Set Supervisor/User Password

English

} PnP/ PCI Con figuratEnte r Passw ord:
ions Save & Exit S etup

Chang e/Set/Dis able Pas sword

When y ou select this function, the follow ing message w ill appear at the center of the screen to assist y ou
in creating a pas sw ord.
Ty pe the passw ord, up to eight characters, and press <Enter>. You will be asked to confirm the passw ord.
Ty pe the passw ord again and press <Enter>. You may also press <Esc> to abort the selection and not
enter a passw ord.
To disable pass w ord, jus t press <Enter> w hen y ou are prompted to enter pass w ord. A mess age
"PASSWORD DISABLED" w ill appear to confirm the pass w ord being disabled. Once the passw ord is
disabled, the sy stem w ill boot and y ou c an enter Setup freely .
The BIOS Setup program allow s y ou to specify tw o separate passw ords:
SUPERVISOR PASSWOR D and a USER PASSWORD. When disabled, any one m ay access all BIOS
Setup program function. When enabled, the Superv is or passw ord is required for entering the BIOS
Setup program and hav ing full configuration fields, the User passw ord is required to access only basic
items.
If y ou select "Sy stem" at "Passw ord Check" in Adv anc e BIOS Features Menu, y ou w ill be prompted
for the passw ord ev ery time the sy stem is rebooted or any time y ou try to enter Setup Menu.
If y ou select "Setup" at "Passw ord Check" in Adv ance BIOS Features Menu, y ou w ill be prompted only
w hen y ou try to enter Setup.

- 31 - BIOS Setup

Save & Exit Setup
English


} PnP/ PCI Con figurat ions Save to CMOS an d EXIT (Y/ N)? Y S etup
Save & Exit

Save Data to CMOS

Ty pe "Y" w ill quit the Setup Utility and sav e the user setup v alue to RTC CMOS.
Ty pe "N" w ill return to Setup Utility .

Exit Without Saving

} PnP/ PCI Con figurat ions Quit Without S aving SaveN)? Exit S etup
(Y/ & N

Aban don all Data

Ty pe "Y" w ill quit the Setup Utility w ithout sav ing to RTC CMOS.
Ty pe "N" w ill return to Setup Utility .


Revision History Drivers
Chapter 3 Install

English
Install Drivers

Pictures below are shown in Windows XP (CD ver. 2.3)
Insert the driver CD-title that came with your motherboard into your CD-ROM drive, the driver
CD-title will auto start and show the installation guide. If not, please double click the CD-ROM
device icon in "My computer", and execute the setup.exe.

INSTALL CHIPSET DRIVER

This page shows the drivers that need to be installed for the system. Click each item to install the driver
manually or switch to the to install the drivers automatically.

The "Xpress Install" uses the"Click and Go" technology to install the drivers automatically. Just select the
drivers you want then click the "GO" button. The will execute the installation for you by itself.

We recommend that you install all components in the list.

Massage: Some device drivers will restart your
system automatically. After restarting your system
the "Xpress Install" will continue to install other
drivers.

Click "GO".

- 33 - Driver Installation

Driver install finished!! you have to reboot system!!
English

Item Description

n VIA 4IN1 Driver
For INF, AGP, IDE and DMA Driver.
n VIA KM266/P4M266 VGA Driver
For VIA KM266/P4M266 VGA driver.
n USB Path for WinXP
This patch driver can help you to resolve the USB device wake up S3 hang up issue in XP.
n VIA Lan Driver *
For VIA LAN driver.
n VIA AC97 Audio Driver
Audio driver for VIA AC97 codec chipset.
n VIA USB 2.0 Controller
For VIA VT8233 (VT6203) / VIA VT8235 / VIA VT8237/ VIA VT8237R south bridge.

For USB2.0 driver support under Windows XP operating system, please use Windows Service
Pack. After install Windows Service Pack, it will show a question mark "?" in "Universal Serial
Bus controller" under "Device Manager". Please remove the question mark and restart the
system (System will auto-detect the right USB2.0 driver).



English
Contact Us

— Taiwan (Headquarters) — Japan
GIGA-BYTE TECHNOLOGY CO., LTD. NIPPON GIGA-BYTE CORPORATION
Address: No.6, Bau Chiang Road, Hsin-Tien, Taipei Hsien, WEB address : http://www.gigabyte.co.jp
Taiwan — Singapore
TEL: +886 (2) 8912-4888 GIGA-BYTE SINGAPORE PTE. LTD.
FAX: +886 (2) 8912-4003 Tech. Support :
Tech. Support : http://tw.giga-byte.com/TechSupport/ServiceCenter.htm
http://tw.giga-byte.com/TechSupport/ServiceCenter.htm Non-Tech. Support (Sales/Marketing) :
Non-Tech. Support (Sales/Marketing) : http://ggts.gigabyte.com.tw/nontech.asp
http://ggts.gigabyte.com.tw/nontech.asp — U.K.
WEB address (English): http://www.gigabyte.com.tw G.B.T. TECH. CO., LTD.
WEB address (Chinese): http://chinese.giga-byte.com Address: GUnit 13 Avant Business Centre 3 Third Avenue, Denbigh
— U.S.A. West Bletchley Milton Keynes, MK1 1DR, UK, England
G.B.T. INC. TEL: +44-1908-362700
Address: 17358 Railroad St, City of Industry, CA 91748. FAX: +44-1908-362709
TEL: +1 (626) 854-9338 Tech. Support :
FAX: +1 (626) 854-9339 http://uk.giga-byte.com/TechSupport/ServiceCenter.htm
Tech. Support : Non-Tech. Support (Sales/Marketing) :
http://www.giga-byte.com/TechSupport/ServiceCenter.htm http://ggts.gigabyte.com.tw/nontech.asp
Non-Tech. Support (Sales/Marketing) : WEB address : http://uk.giga-byte.com
http://ggts.gigabyte.com.tw/nontech.asp — The Netherlands
WEB address : http://www.giga-byte.com GIGA-BYTE TECHNOLOGY B.V.
— Germany TEL: +31 40 290 2088
G.B.T. TECHNOLOGY TRADING GMBH NL Tech.Support: 0900-GIGABYTE (0900-44422983)
Address: Friedrich-Ebert-Damm 112 22047 Hamburg BE Tech.Support: 0900-84034
TEL: +49-40-2533040 (Sales) FAX: +31 40 290 2089
+49-1803-428468 (Tech.) Tech. Support :
FAX: +49-40-25492343 (Sales) http://nz.giga-byte.com/TechSupport/ServiceCenter.htm
+49-1803-428329 (Tech.) Non-Tech. Support (Sales/Marketing) :
Tech. Support : http://ggts.gigabyte.com.tw/nontech.asp
http://de.giga-byte.com/TechSupport/ServiceCenter.htm WEB address : http://www.giga-byte.nl
Non-Tech. Support (Sales/Marketing) :
http://ggts.gigabyte.com.tw/nontech.asp
WEB address : http://www.gigabyte.de

- 35 - Contact Us

— China — Australia
English

NINGBO G.B.T. TECH. TRADING CO., LTD. GIGABYTE TECHNOLOGY PTY. LTD.
Tech. Support : Address: 3/6 Garden Road, Clayton, VIC 3168 Australia
http://cn.giga-byte.com/TechSupport/ServiceCenter.htm TEL: +61 3 85616288
Non-Tech. Support (Sales/Marketing) : FAX: +61 3 85616222
http://ggts.gigabyte.com.tw/nontech.asp Tech. Support :
WEB address : http://www.gigabyte.com.cn http://www.giga-byte.com.au/TechSupport/ServiceCenter.htm
Shanghai Non-Tech. Support (Sales/Marketing) :
TEL: +86-021-63410999 http://ggts.gigabyte.com.tw/nontech.asp
FAX: +86-021-63410100 WEB address : http://www.giga-byte.com.au
Beijing — France
TEL: +86-010-82886651 GIGABYTE TECHNOLOGY FRANCES S.A.R.L.
FAX: +86-010-82888013 Tech. Support :
Wuhan http://tw.giga-byte.com/TechSupport/ServiceCenter.htm
TEL: +86-027-87851061 Non-Tech. Support (Sales/Marketing) :
FAX: +86-027-87851330 http://ggts.gigabyte.com.tw/nontech.asp
GuangZhou WEB address : http://www.gigabyte.fr
TEL: +86-020-87586074 — Russia
FAX: +86-020-85517843 Moscow Representative Office Of Giga-Byte Technology Co.,
Chengdu Ltd.
TEL: +86-028-85236930 Tech. Support :
FAX: +86-028-85256822 http://tw.giga-byte.com/TechSupport/ServiceCenter.htm
Xian Non-Tech. Support (Sales/Marketing) :
TEL: +86-029-85531943 http://ggts.gigabyte.com.tw/nontech.asp
FAX: +86-029-85539821 WEB address : http://www.gigabyte.ru
Shenyang — Poland
TEL: +86-024-23960918 Representative Office Of Giga-Byte Technology Co., Ltd.
FAX: +86-024-23960918-809 POLAND
Tech. Support :
http://tw.giga-byte.com/TechSupport/ServiceCenter.htm
Non-Tech. Support (Sales/Marketing) :
http://ggts.gigabyte.com.tw/nontech.asp
WEB address : http://www.gigabyte.pl


Motherboard manual 8vm533m-rz_e

More Related Content

What's hot (13)

Viewers also liked (20)

Similar to Motherboard manual 8vm533m-rz_e (20)

Recently uploaded (20)

Motherboard manual 8vm533m-rz_e