Acces Point Dap 2360 - Manual

Table of Contents

Table of Contents
Product Overview......................................................... 4 LAN . ................................................................ 28
Package Contents.................................................... 4 Advanced Settings. ................................................ 29
.
System Requirements.............................................. 4 Performance..................................................... 29
Introduction............................................................... 5 Multi-SSID. ....................................................... 31
.
Features................................................................... 7 VLAN................................................................ 33
VLAN List...................................................... 33
Wireless Basics............................................................ 8
Port List......................................................... 34
Standards-Based Technology.................................. 9
Add/Edit VLAN.............................................. 35
Wireless Installation Considerations. ..................... 10
.
PVID Setting................................................. 36
.
Hardware Overview................................................ 11
Intrusion............................................................ 37
Connect Power over Ethernet (PoE)................ 12
Schedule........................................................... 38
Four Operational Modes............................................ 13 QoS. ................................................................. 39
.
AP Array........................................................... 41
Getting Started........................................................... 14
. Wireless Basic Settings................................ 42
.
Configuration.............................................................. 15 Wireless Advanced Settings......................... 42
Save and Activate Settings. ................................... 16
. Multiple SSID & VLAN.................................. 43
.
Basic Settings......................................................... 17 Advanced Functions..................................... 43
.
Wireless ........................................................... 17 Administration Settings................................. 43
Access Point mode....................................... 17 ARP Spoofing Prevention................................. 44
WDS with AP mode ..................................... 19 DHCP Server ................................................... 45
WDS mode.................................................... 21 Dynamic Pool Settings.................................. 45
Wireless Client mode.................................... 23 Static Pool Setting......................................... 47
Open System/Shared Key Authentication . .. 24 Current IP Mapping List................................ 49
WPA/WPA2-Personal Authentication........... 25 . Filters................................................................ 50
WPA/WPA2-Enterprise Authentication......... 26 Wireless MAC ACL....................................... 50
802.1x Authentication................................... 27
. WLAN Partition............................................. 51
.

D-Link DAP-2360 User Manual 2

Table of Contents

Status .................................................................... 52 Technical Specifications........................................... 75
Device Information............................................ 52
Client Information. ............................................ 53
.
WDS Information.............................................. 54
Stats. ................................................................ 55
.
Ethernet........................................................ 55
.
WLAN Traffic................................................. 56
Log.................................................................... 57
View Log....................................................... 57
Log Settings.................................................. 58
Maintenance .......................................................... 59
Administration Settings..................................... 59
Limit Administrator........................................ 60
System Name Settings................................. 61
.
Login Settings............................................... 62
Console Settings........................................... 63
SNMP Settings.............................................. 64
Firmware and SSL Certification Upload................. 65
Configuration File Upload....................................... 66
Time and Date........................................................ 67
System.............................................................. 68
System Settings............................................ 68
Help........................................................................ 69

Troubleshooting......................................................... 70

Networking Basics..................................................... 72
Check your IP address........................................... 72
Statically Assign an IP address.............................. 73


Section 1 - Product Overview

Product Overview
Package Contents

• D-Link DAP-2360 AirPremier® N PoE Access Point
• Power Adapter
• CAT5 Ethernet Cable
• CD-ROM with User Manual
• Install Guide

Note: Using a power supply with a different voltage rating than the one included
with the DAP-2360 will cause damage and void the warranty for this product.

System Requirements
• Computers with Windows®, Macintosh®, or Linux-based operating systems with an installed Ethernet
Adapter
• For configuration, the following web browsers are supported:
• Microsoft® Internet Explorer® 6.0 and higher
• Mozilla Firefox 3.0 and higher
• Google™ Chrome 2.0 and higher
• Apple Safari 3.0 and higher



Introduction
The DAP-2360 802.11n AP increases productivity by allowing you to work faster and more efficiently. With the DAP-
2360, bandwidth-intensive applications like graphics or multimedia will benefit significantly because large files are now
able to move across the network quickly.

The DAP-2360 is capable of operating in one of four different wireless networking modes: access point, WDS (Wireless
Distribution System) with AP, WDS, or Wireless Client mode.

Use less wiring, enjoy increased flexibility, save time and money with PoE (Power over Ethernet). With PoE, the
DAP-2360 shares power and data over the CAT5 cable, making the setup of your network less expensive and more
convenient.

An ideal solution for quickly creating and extending a wireless local area network (WLAN) in offices or other workplaces,
trade shows, and special events, the DAP-2360 provides data transfer rates up to 300Mbps. (The 802.11n standard
is backwards compatible with 802.11g and 802.11b devices.)

WPA/WPA2 is offered in two options: Enterprise (used for corporations) and Personal (used for home users).
WPA-Personal and WPA2-Personal are directed towards home users who do not have the server-based equipment
required for user authentication. This method of authentication is similar to WEP because you define a “Pre-Shared
Key” on the wireless router/AP. Once the pre-shared key is confirmed and satisfied at both the client and access point,
access is then granted. The encryption method used is referred to as the Temporal Key Integrity Protocol (TKIP), which
offers per-packet dynamic hashing. It also includes an integrity checking feature which ensures that the packets were
not tampered with during wireless transmission.



WPA-Enterprise and WPA2-Enterprise are ideal for businesses that already have existing security infrastructures
established. Management and security implementation can now be centralized on a server participating on the network.
Utilizing 802.1X with a RADIUS (Remote Authentication Dial-in User Service) server, a network administrator can
define a list of authorized users who can access the wireless LAN. When attempting to access a wireless LAN with
WPA-Enterprise configured, the new client will be requested to enter a username with a password. If the new client is
authorized by the administration, and enters the correct username and password, then access is granted. In the case
where an employee leaves the company, the network administrator is able to remove the previous employee from the
authorized list to avoid compromising the network.
EAP (Extensible Authentication Protocol) is available through the Windows® XP operating system. You will need to
use the same type of EAP protocol on all devices in your network when using the 802.1X feature.

*Maximum wireless signal rate derived from IEEE Standard 802.11n and 802.11g specifications. Actual data throughput may vary. Network
conditions and environmental factors, including volume of network traffic, building materials and construction, and network overhead can
lower actual data throughout rate.



Features
• Four different operation modes - Capable of operating in one of four different operation modes to meet your
wireless networking needs: Access Point, WDS with AP, WDS, or Wireless Client.
• Faster wireless networking with the 802.11n standard to provide a maximum wireless signal rate of up to 300
Mbps*.
• Compatible with the 802.11b standard to provide a wireless data rate of up to 11Mbps, allowing you to migrate
your system to the 802.11n and 802.11g standards on your own schedule without sacrificing connectivity.
• Compatible with the 802.11g standard to provide a wireless data rate of up to 54Mbps in the 2.4GHz frequency
range.
• Better security with WPA - The DAP-2360 can securely connect wireless clients on the network using WPA (Wi-Fi
Protected Access) to provide a much higher level of security for your data and communications than its previous
versions.
• AP Manager II management software - The real-time display of the network's topology and AP’s information
makes network configuration and management quick and simple.
• SNMP for management - The DAP-2360 is not just fast, but also supports SNMP v.3 for better network
management. Superior wireless AP manager software is bundled with the DAP-2360 for network configuration
and firmware upgrade. Systems administrators can also set up the DAP-2360 easily with the Web-based
configuration. A D-Link D-View 6.0 module will be downloadable for network administration and real-time
network traffic monitoring with D-Link D-View 6.0 software.
• Utilizes OFDM technology (Orthogonal Frequency Division Multiplexing).
• Supports 802.3af Power over Ethernet.
• Supports one 10/100/1000M Ethernet port.
• Operates in the 2.4 ~ 2.4835GHz frequency ranges.
• Web-based interface for managing and configuring.
*Maximum wireless signal rate derived from IEEE Standard 802.11n and 802.11g specifications. Actual data throughput may vary. Network conditions and environmental
factors, including volume of network traffic, building materials and construction, and network overhead can lower actual data throughout rate.


Section 2 - Installation

Wireless Basics
D-Link wireless products are based on industry standards to provide high-speed wireless connectivity that is easy to
use within your home, business or public access wireless networks. D-Link wireless products provides you with access
to the data you want, whenever and wherever you want it. Enjoy the freedom that wireless networking can bring to you.
WLAN use is not only increasing in both home and office environments, but in public areas as well, such as airports,
coffee shops and universities. Innovative ways to utilize WLAN technology are allowing people to work and communicate
more efficiently. Increased mobility and the absence of cabling and other types of fixed infrastructure have proven to
be beneficial to many users.
Wireless adapter cards used on laptop and desktop systems support the same protocols as Ethernet adapter cards,
allowing wireless users to use the same applications as those used on a wired network.

People use WLAN technology for many different purposes:
Mobility - productivity increases when people can have access to data in any location within the operating range
of their WLAN. Management decisions based on real-time information can significantly improve the efficiency
of a worker.
Low implementation costs - WLANs are easy to set up, manage, change and relocate. Networks that frequently
change can benefit from WLAN's ease of implementation. WLANs can operate in locations where installation of
wiring may be impractical.
Installation and network expansion - by avoiding the complications of troublesome cables, a WLAN system
can be fast and easy during installation, especially since it can eliminate the need to pull cable through walls
and ceilings. Wireless technology provides more versatility by extending the network beyond the home or office.
Inexpensive solution - wireless network devices are as competitively priced as conventional Ethernet network
devices. The DAP-2360 saves money by providing users with multi-functionality configurable in four different
modes.
Scalability - Configurations can be easily changed and range from Peer-to-Peer networks, suitable for a small
number of users to larger Infrastructure networks to accommodate hundreds or thousands of users, depending
on the number of wireless devices deployed.



Standards-Based Technology
The DAP-2360 Wireless Access Point utilizes the 802.11b, 802.11g, and 802.11n standards.

The IEEE 802.11n standard is an extension of the 802.11b and 802.11g standards that came before it. It increases
the maximum wireless signal rate up to 300Mbps* within the 2.4GHz bands, utilizing OFDM technology.

This means that in most environments - within the specified range of this device - you will be able to transfer large files
quickly, or even watch a movie in MPEG format over your network without noticeable delays. This technology works
by transmitting high-speed digital data over a radio wave utilizing OFDM (Orthogonal Frequency Division Multiplexing)
technology. OFDM works by splitting the radio signal into multiple smaller sub-signals that are then simultaneously
transmitted at different frequencies to the receiver. OFDM reduces the amount of crosstalk (interference) in signal
transmissions.

The D-Link DAP-2360 will automatically sense the best possible connection speed to ensure the greatest possible
speed and range.

IEEE 802.11n offers the most advanced network security features available today, including WPA.

*Maximum wireless signal rate derived from IEEE Standard 802.11n and 802.11g specifications. Actual data throughput may vary. Network conditions and environmental factors, including volume of network
traffic, building materials and construction, and network overhead can lower actual data throughout rate.



Wireless Installation Considerations
The D-Link AirPremier® N wireless access point lets you access your network using a wireless connection from virtually
anywhere within the operating range of your wireless network. Keep in mind, however, that the number, thickness and
location of walls, ceilings, or other objects that the wireless signals must pass through, may limit the range. Typical
ranges vary depending on the types of materials and background RF (radio frequency) noise in your home or business.
The key to maximizing wireless range is to follow these basic guidelines:

1. Keep the number of walls and ceilings between the access point and other network devices to a minimum.
Each wall or ceiling can reduce your adapter’s range from 3-90 feet (1-30 meters). Position your devices
so that the number of walls or ceilings is minimized.

2. Be aware of the direct line between network devices. A wall that is 1.5 feet thick (.5 meters), at a
45-degree angle appears to be almost 3 feet (1 meter) thick. At a 2-degree angle, it looks over 42 feet
(14 meters) thick! Position devices so that the signal will travel straight through a wall or ceiling (instead
of at an angle) for better reception.

3. Building Materials make a difference. A solid metal door or aluminum studs may have a negative effect
on the range. Try to position access points, wireless routers, and computers so that the signal passes
through drywall or open doorways. Materials and objects such as glass, steel, metal, walls with insulation,
water (fish tanks), mirrors, file cabinets, brick, and concrete will degrade your wireless signal.

4. Keep your product away (at least 3-6 feet or 1-2 meters) from electrical devices or appliances that
generate RF noise.

5. If you are using 2.4GHz cordless phones or X-10 (wireless products such as ceiling fans, lights, and
home security systems), your wireless connection may degrade dramatically or drop completely. Make
sure your 2.4GHz phone base is as far away from your wireless devices as possible. The base transmits
a signal even if the phone in not in use.



Hardware Overview

Power Receptacle Power LED
The supplied power adapter connects here. This light will be solid green when the unit is powered on.

Reset Button 2.4 GHz LED
A pinhole button located beside the Ethernet socket is used to reset This light will be flickering green when the 2.4GHz frequency is in
the system or restore the factory default settings. use.
Note: After resetting the unit, you will still be able to access the
data on your hard drives. LAN LED
This light will be flickering green when there is active LAN traffic.
LAN (PoE) Port
An Ethernet port that connects the unit to a network. This port can
also be used to supply power to this unit using Power over Ethernet.



Connect Power over Ethernet (PoE)

Connect one end of an Ethernet cable (included with your access point) to the LAN port on the DAP-2360 and the other end of the Ethernet
cable to either your computer or to your PoE switch. The AP can be powered on by a PoE switch or by the power adapter shipped with
the AP.



Four Operational Modes

Access Point (AP) Create a wireless LAN

Wirelessly connect multiple networks while still
WDS with AP
functioning as a wireless AP

WDS Wirelessly connect multiple networks

Wireless Client AP acts as a wireless network adapter for your Ethernet-
enabled device



Getting Started

1. You will need broadband Internet access.
2. Consult with your cable or DSL provider for proper installation of the modem.
3. Connect the cable or DSL modem to a router. See the printed Install Guide included with your router.
4. If you are connecting a desktop computer to your network, install a wireless PCI adapter into an available
PCI slot on your desktop computer.
5. Install the drivers for your wireless CardBus adapter into a laptop computer.


Section 3 - Configuration

Configuration
To configure the DAP-2360, use a computer that is connected to the DAP-2360 with an Ethernet cable (see the Network
Layout diagram).

Launch your web browser.
Type the IP address of the DAP-2360 in the address field (http://192.168.0.50)
and press Enter. Make sure that the IP addresses of the DAP-2360 and your
computer are in the same subnet.

Note: If you have changed the default IP address assigned to the DAP-2360, make sure to enter the correct IP address.

Enter the user name (admin) and your password. Leave the password field blank by default and click Login.

Note: If you have changed the password, make
sure to enter the correct password.



After successfully logging into the DAP-2360, the following screen will appear:

Save and Activate Settings
When making changes on most of the configuration screens in this section, use the button at the bottom of
each screen to save (not activate) your configuration changes.

You may change settings to multiple pages before activating. Once you are finished, click the Configuration button
located at the top of the page and then click Save and Activate.



Basic Settings
Wireless
Access Point mode
Wireless Band: Select 2.4GHz from the drop-down menu.

Mode: Select Access Point from the drop-down
menu. The other three choices are WDS with
AP, WDS, and Wireless Client.

Network Name Service Set Identifier (SSID) is the name
(SSID): designated for a specific wireless local area
network (WLAN). The SSID’s factory default
setting is dlink. The SSID can be easily
changed to connect to an existing wireless
network or to establish a new wireless network.
The SSID can be up to 32 characters and is
case-sensitive.

SSID Enable or Disable SSID visibility. Enabling
Visibility: this feature broadcasts the SSID across the
network, thus making it visible to all network
users.

Auto Channel Enabling this feature automatically selects the
Selection: channel that provides the best wireless performance. Enable is set by default. The channel selection process only occurs
when the AP is booting up.

Channel: All devices on the network must share the same channel. To change the channel, first toggle the Auto Channel Selection
setting to Disable, and then use the drop-down menu to make the desired selection.
Note: The wireless adapters will automatically scan and match the wireless settings.



Channel Width: Allows you to select the channel width you would like to operate in. Select 20 MHz if you are not using any 802.11n wireless
clients. Auto 20/40 MHz allows you to connect to both 802.11n and 802.11b/g wireless devices on your network.

Authentication: Use the drop-down menu to choose Open System, Shared Key, WPA-Personal, WPA-Enterprise, or 802.11x.

Select Open System to communicate the key across the network.

Select Shared Key to limit communication to only those devices that share the same WEP settings. If multi-SSID is enabled,
this option is not available.

Select WPA-Personal to secure your network using a password and dynamic key changes. No RADIUS server is required.

Select WPA-Enterprise to secure your network with the inclusion of a RADIUS server.

Select 802.1x to secure your network using 802.1x authentication.



WDS with AP mode
In WDS with AP mode, the DAP-2360 wirelessly connects multiple networks while still functioning as a wireless AP.


Mode: WDS with AP mode is selected from the drop-down
menu.

Network Name Service Set Identifier (SSID) is the name designated
(SSID): for a specific wireless local area network (WLAN). The
SSID’s factory default setting is dlink. The SSID can
be easily changed to connect to an existing wireless

SSID Visibility: Enable or Disable SSID visibility. Enabling this feature
broadcasts the SSID across the network, thus making
it visible to all network users.

Auto Channel Enabling this feature automatically selects the channel
Selection: that will provide the best wireless performance. This
feature is not supported in WDS with AP mode. The
channel selection process only occurs when the AP
is booting up.

Channel: To change the channel, use the drop-down menu
to make the desired selection. (Note: The wireless
adapters will automatically scan and match the
wireless settings.)

Channel Width: Indicates whether the device is capable of 20MHz operation only or both 20MHz and 40MHz operation.



Remote AP nter the MAC addresses of the APs on your network that will serve as bridges to wirelessly connect multiple networks.
E
MAC Address:

Site Survey: Click on the Scan button to search for available wireless networks, then click on the available network that you want to
connect with.

Authentication: Use the drop-down menu to choose Open System, Shared Key, or WPA-Personal.
Select Shared Key to limit communication to only those devices that share the same WEP settings. If multi-SSID is enabled,
this option is not available.



WDS mode
In WDS mode, the DAP-2360 wirelessly connects multiple networks, without functioning as a wireless AP.


Mode: WDS is selected from the drop-down menu.

Network Service Set Identifier (SSID) is the name
Name (SSID): designated for a specific wireless local area
setting is dlink. The SSID can be easily changed
to connect to an existing wireless network or to
establish a new wireless network.

SSID Enable or Disable SSID visibility. Enabling this
Visibility: feature broadcasts the SSID across the network,
thus making it visible to all network users.

Auto Channel Enabling this feature automatically selects
Selection: the channel that will provide the best wireless
performance. This feature is not supported in
WDS mode.

Channel: All devices on the network must share the
same channel. To change the channel, use the
drop-down menu to make the desired selection.

Channel Use the drop-down menu to choose 20 MHz or
Width: Auto 20/40 MHz.

Remote Enter the MAC addresses of the APs on your
AP MAC network that will serve as bridges to wirelessly
Address: connect multiple networks.



Site Survey: Click on the Scan button to search for available wireless networks, then click on the available network that you want to
connect with.

Authentication: Use the drop-down menu to choose Open System, Shared Key, or WPA-Personal.
Select Shared Key to limit communication to only those devices that share the same WEP settings.



Wireless Client mode
Mode: Wireless Client is selected from the drop-down menu.

Network Name Service Set Identifier (SSID) is the name designated for a specific
(SSID): wireless local area network (WLAN). The SSID’s factory default
setting is dlink. The SSID can be easily changed to connect to an
existing wireless network.

SSID Visibility: This option is unavailable in Wireless Client mode.

Auto Channel Enabling this feature automatically selects the channel that
Selection: will provide the best wireless performance. This feature is not
supported in Wireless Client mode.

Channel: The channel used will be displayed, and matches the AP that the
DAP-2360 is connected to when set to Wireless Client mode.

Channel Width: Use the drop-down menu to choose 20 MHz or Auto 20/40 MHz.

Site Survey: Click on the Scan button to search for available wireless networks,
then click on the available network that you want to connect with.
Use the drop-down menu to choose Open System or
WPA-Personal.

Authentication: Select Open System to communicate the key across the network.
Select WPA-Personal to secure your network using a password
and dynamic key changes. No RADIUS server is required.

Enable: Check to enable clone MAC. This feature will allow you to change
the MAC address of the access point to the MAC address of a
client.

MAC Source: Select the MAC source from the drop-down menu.

MAC Address: Enter the MAC address that you would like to assign to the access
point.



Open System/Shared Key Authentication
Encryption: Use the radio button to disable or enable
encryption.

Key Type*: Select HEX or ASCII.

Key Size: Select 64 Bits or 128 Bits.

Key Index (1- Select the 1st through the 4th key to be the
4): active key.

Input up to four keys for encryption. You will
Key: select one of these keys in the Key Index
drop-down menu.

**Hexadecimal (HEX) digits consist of the numbers 0-9 and the letters A-F.
*ASCII (American Standard Code for Information Interchange) is a code that represents English letters using numbers ranging
from 0-127.



WPA/WPA2-Personal Authentication
WPA Mode: When WPA-Personal is selected for Authentication
type, you must also select a WPA mode from the
drop-down menu: AUTO (WPA or WPA2), WPA2
Only, or WPA Only. WPA and WPA2 use different
algorithms. AUTO (WPA or WPA2) allows you to
use both WPA and WPA2.

Cipher Type: When you select WPA-Personal, you must also
select AUTO, AES, or TKIP from the drop-down
menu.

Group Key Select the interval during which the group key will be
Update: valid. The default value of 1800 is recommended.
Select Manual to enter your key (PassPhrase).

Periodical You can select Periodical Key Change to have
Key Change: the access point automatically change your
PassPhrase. Enter the Activate From time and the
time in hours to change the key.

PassPhrase: When you select WPA-Personal, please enter a
PassPhrase in the corresponding field.



WPA/WPA2-Enterprise Authentication
WPA Mode: When WPA-Enterprise is selected, you must
also select a WPA mode from the drop-down
menu: AUTO (WPA or WPA2), WPA2 Only,
or WPA Only. WPA and WPA2 use different
algorithms. AUTO (WPA or WPA2) allows you
to use both WPA and WPA2.

Cipher Type: When WPA-Enterprise is selected, you must
also select a cipher type from the drop-down
menu: Auto, AES, or TKIP.

Group Key Select the interval during which the group key
Update will be valid. The recommended value is 1800.
Interval: A lower interval may reduce data transfer rates.

Network Enable or disable Microsoft Network Access
Access Protection.
Protection:

RADIUS Enter the IP address of the RADIUS server.
Server:

RADIUS Port: Enter the RADIUS port.

RADIUS Enter the RADIUS secret.
Secret:



802.1x Authentication
Key Update Select the interval during which the group
Interval: key will be valid (300 is the recommended
value). A lower interval may reduce data
transfer rates.

RADIUS Server: Enter the IP address of the RADIUS server.


RADIUS Secret: Enter the RADIUS secret.



LAN
LAN is short for Local Area Network. This is considered your internal network. These are the IP settings of the LAN
interface for the DAP-2360. These settings may be referred to as private settings. You may change the LAN IP address
if needed. The LAN IP address is private to your internal network and cannot be seen on the Internet.

Get IP Static IP (Manual) is chosen here. Choose this
From: option if you do not have a DHCP server in your
network, or if you wish to assign a static IP address
to the DAP-2360. When Dynamic IP (DHCP) is
selected, the other fields here will be grayed out.
Please allow about two minutes for the DHCP client
to be functional once this selection is made.

IP The default IP address is 192.168.0.50. Assign a
Address: static IP address that is within the IP address range
of your network.

Subnet Enter the subnet mask. All devices in the network
Mask: must share the same subnet mask.

Default Enter the IP address of the gateway in your network.
Gateway: If there is a gateway in your network, please enter
an IP address within the range of your network.



Advanced Settings
Performance
Wireless: Use the drop-down menu to turn the wireless
function On or Off.

Wireless Mode: The different combination of clients that can
be supported include Mixed 802.11n, 802.11g
and 802.11b, Mixed 802.11g and 802.11b
and 802.11n Only. Please note that when
backwards compatibility is enabled for legacy
(802.11g/b) clients, degradation of 802.11n
wireless performance is expected.

Data Rate*: Indicate the base transfer rate of wireless
adapters on the wireless LAN. The AP will
adjust the base transfer rate depending on
the base rate of the connected device. If there
are obstacles or interference, the AP will step
down the rate. This option is enabled in Mixed
802.11g and 802.11b mode. The choices
available are Best (Up to 54), 54, 48, 36, 24,
18, 12, 9, 6, 11, 5.5, 2 or 1.

*Maximum wireless signal rate derived from IEEE Standard 802.11n and 802.11g specifications. Actual data throughput may vary. Network conditions and environmental
factors, including volume of network traffic, building materials and construction, and network overhead can lower actual data throughout rate.



Beacon Interval Beacons are packets sent by an access point to synchronize a wireless network. Specify a value in milliseconds. The
(25-500): default (100) is recommended. Setting a higher beacon interval can help to save the power of wireless clients, while
setting a lower one can help a wireless client connect to an access point faster.
DTM Interval Select a Delivery Traffic Indication Message setting between 1 and 15. The default value is 1. DTIM is a countdown in-
(1-15): forming clients of the next window for listening to broadcast and multicast messages.
Transmit Power: This setting determines the power level of the wireless transmission. Transmitting power can be adjusted to eliminate
overlapping of wireless area coverage between two access points where interference is a major concern. For example,
if wireless coverage is intended for half of the area, then select 50% as the option. Use the drop-down menu to select
100%, 50%, 25%, or 12.5%.

WMM (Wi-Fi WMM stands for Wi-Fi Multimedia. Enabling this feature will improve the user experience for audio and video applica-
Multimedia): tions over a Wi-Fi network.

Ack Time Out To effectively optimize throughput over long distance links, enter a value for Acknowledgement Time Out from 64 to 200
(2.4 GHZ, 64~200) : microseconds in the 2.4 GHz in the field provided.

Short GI: Select Enable or Disable. Enabling a short guard interval can increase throughput. However, be aware that it can also
increase the error rate in some installations due to increased sensitivity to radio-frequency installations.

IGMP Snooping: Select Enable or Disable. Internet Group Management Protocol allows the AP to recognize IGMP queries and reports
sent between routers and an IGMP host (wireless STA). When IGMP snooping is enabled, the AP will forward multicast
packets to an IGMP host based on IGMP messages passing through the AP.

Connection Limit: Select Enable or Disable. This is an option for load balancing. This determines whether to limit the number of users
accessing this device. The exact number is entered in the User Limit field below. This feature allows the user to share
the wireless network traffic and the client using multiple APs. If this function is enabled, when the number of users
exceeds this value, the DAP-2360 will not allow clients to associate with the AP.

User Limit (0-64): Set the maximum amount of users that are allowed access (0-64 users). To use this feature, the Connection Limit
above must be enabled. For most users, a limit of 10 is recommended. The default setting is 20.

Multicast Rate for Select the multicast rate for 2.4G band. The choices available are 130,117,78,65,58.5,54, 52,48, 39,36, 26,24, 19.5,18,
2.4G Band 13,12, 9, 6.5,6, 11, 5.5, 2 or 1.



Multi-SSID
The device supports up to four multiple Service Set Identifiers. In the Basic > Wireless section, you can set the Primary
SSID. The SSID’s factory default setting is dlink. The SSID can be easily changed to connect to an existing wireless

Enable Check to enable support for multiple SSIDs.
Multi-SSID:

Band: This read-only value is the current band
setting.

Index: You can select up to three multi-SSIDs. With
the Primary SSID, you have a total of four
multi-SSIDs.

SSID: Service Set Identifier (SSID) is the name
designated for a specific wireless local area
setting is dlink. The SSID can be easily
changed to connect to an existing wireless
network or to establish a new wireless
network.

SSID Visibility: Enable or Disable SSID visibility. Enabling
this feature broadcasts the SSID across the
network, thus making it visible to all network
users.

Security: The Multi-SSID security can be Open System, WPA-Personal, WPA-Enterprise, or 802.1x. For a detailed description
of the Open System parameters, please go to page 25. For a detailed description of the WPA-Personal parameters,
please go to page 26. For a detailed description of the WPA-Enterprise parameters, please go to page 27. For a detailed
description of the O802.1x parameters, please go to page 28.



Priority: Check the Enable Priority box at the top of this window to enable. Select the priority from the drop-down menu.

WMM (Wi-Fi Select Enable or Disable.
Multimedia):
Encryption: When you select Open System, toggle between Enable and Disable. If Enable is selected, the Key Type, Key Size, Key
Index (1~4), Key, and Confirm Keys must also be configured.

Key Type: Select HEX or ASCII.

Key Size: Select 64 Bits or 128 Bits.

Key Index (1-4): Select from the 1st to 4th key to be set as the active key.

Key: Input up to four keys for encryption. You will select one of these keys in the Key Index drop-down menu.

WPA Mode: When you select either WPA-Personal or WPA-Enterprise, you must also choose a WPA mode from the drop-down menu:
AUTO (WPA or WPA2), WPA2 Only, or WPA Only. WPA and WPA2 use different algorithms. AUTO (WPA or WPA2)
allows you to use both WPA and WPA2. In addition, you must configure Cipher Type and Group Key Update Interval.

Cipher Type: Select Auto, AES, or TKIP from the drop-down menu.

Group Key Update Select the interval during which the group key will be valid. The default value of 1800 seconds is recommended.
Interval:

PassPhrase: When you select WPA-Personal, please enter a PassPhrase in the corresponding field.

Confirm When you select WPA-Personal, please re-enter the PassPhrase entered in the previous item in the corresponding field.
PassPhrase:

RADIUS Server: When you select WPA-Enterprise, enter the IP address of the RADIUS server. In addition, you must configure RADIUS
Port and RADIUS Secret.


RADIUS Secret: Enter the RADIUS secret.



VLAN
VLAN List
The DAP-2360 supports VLANs. VLANs can be created with a Name and VID. Mgmt (TCP stack), LAN, Primary/
Multiple SSID, and WDS connection can be assigned to VLANs as they are physical ports. Any packet which enters the
DAP-2360 without a VLAN tag will have a VLAN tag inserted with a PVID.
The VLAN List tab displays the current VLANs.

VLAN Status: Use the radio button to toggle between
Enable or Disable. Next, go to the Add/Edit
VLAN tab to add or modify an item on the
VLAN List tab.



Port List
The Port List tab displays the current ports. If you want to configure the guest and internal networks on a Virtual LAN
(VLAN), the switch and DHCP server you are using must also support VLANs. As a prerequisite step, configure a port
on the switch for handling VLAN tagged packets as described in the IEEE 802.1Q standard.

VLAN Status: Use the radio button to toggle to Enable. Next,
go to the Add/Edit VLAN tab to add or modify
an item on the VLAN List tab.

Port Name: The name of the port is displayed in this
column.

Tag VID: The Tagged VID is displayed in this column.

Untag VID: The Untagged VID is displayed in this column.

PVID: The Port VLAN Identifier is displayed in this
column.



Add/Edit VLAN
The Add/Edit VLAN tab is used to configure VLANs. Once you have made the desired changes, click the Save button
to let your changes take effect.

VLAN Status: Use the radio button to toggle to Enable.

VLAN ID: Provide a number between 1 and 4094 for
the Internal VLAN.

VLAN Name: Enter the VLAN to add or modify.



PVID Setting
The PVID Setting tab is used to enable/disable the Port VLAN Identifier Auto Assign Status as well as to configure
various types of PVID settings. Click the Save button to let your changes take effect.

VLAN Status: Use the radio button to toggle between
Enable and Disable.

PVID Auto Assign Use the radio button to toggle PVID auto
Status: assign status to Enable.



Intrusion
The Wireless Intrusion Protection window is used to set APs as All, Valid, Neighborhood, Rogue, and New. Click
the Save button to let your changes take effect.

AP List: The choices include All, Valid, Neighbor,
Rogue, and New.

Detect: Click this button to initiate a scan of the
network.



Schedule
The Wireless Schedule Settings window is used to add and modify scheduling rules on the device. Click the Save
button to let your changes take effect.

Wireless Use the drop-down menu to enable the
Schedule: device’s scheduling feature.

Name: Enter a name for the new scheduling rule in
the field provided.

Index: Select the index from the drop-down menu.

SSID: Enter the name of your wireless network
(SSID).

Day(s): Toggle the radio button between All Week
and Select Day(s). If the second option is
selected, check the specific days you want
the rule to be effective on.

All Day(s): Check this box to have your settings apply
24 hours a day.

Start Time: Enter the start time for your rule. If you
selected All Day, this option will be greyed
out.

End Time: Enter the end time for your rule.

Add: Click to add the rule to the list.

Schedule Rule This section will display the list of created
List: schedules.

Save: Click the Save button to save your created rules.



QoS
Quality of Service (QoS) enhances the experience of using a network by prioritizing the traffic of different applications.
A QoS Rule identifies a specific message flow and assigns a priority to that flow. For most applications, the priority
classifiers ensure the right priorities and specific QoS Rules are not required. QoS supports overlaps between rules.
If more than one rule matches a specific message flow, the rule with the highest priority will be used.

QoS (Quality of Enable this option if you want to allow QoS to
Service): prioritize your traffic Priority Classifiers.

HTTP: Allows the access point to recognize HTTP
transfers for many common audio and video
streams and prioritize them above other traffic.
Such streams are frequently used by digital
media players.

Automatic: When enabled, this option causes the access
point to automatically attempt to prioritize traffic
streams that it does not otherwise recognize,
based on the behavior that the streams exhibit.
This acts to de-prioritize streams that exhibit
bulk transfer characteristics, such as file
transfers, while leaving interactive traffic, such
as gaming or VoIP, running at a normal priority.



Name: Enter a name for the new QoS rule in the field provided.

Priority: Use the drop-down menu to select the desired priority: Background (BK), Best Effort (BE), Video (VI), or Voice (VO).

Protocol: Use the drop-down menu to choose the appropriate protocol used by the messages: Any, TCP, UDP, Both, IMCP, or Other.

Host 1 IP Range: The rule applies to a flow of messages for which one computer’s IP address falls within the range set here.

Host 1 Port The rule applies to a flow of messages for which host 1’s port number is within the range set here when the Protocol is set
Range: to TCP, UDP, or Both.

Host 2 IP Range: The rule applies to a flow of messages for which the other computer’s IP address falls within the range set here.

Host 2 Port The rule applies to a flow of messages for which host 2’s port number is within the range set here when the Protocol is set
Range: to TCP, UDP, or Both.



AP Array
An AP array is a set of devices on a network that are organized into a single group to increase ease of management.

Enable Array: This check box allows the user to enable the AP array
function. The three modes that are available are Master,
Backup Master, and Slave. APs in the same array will
use the same configuration. The configuration will sync
the Master AP to the Slave AP and the Backup Master
AP when a Slave AP and a Backup Master AP join the
AP array.

AP Array Name: Enter a name for the AP array you have created.

AP Array Enter a password that will be used to access the AP
Password: array you have created.

Scan AP Array Click this button to initiate a scan of all the available
List: APs currently on the network.

AP Array List: This table displays the current AP array status for the
following parameters: Array Name, Master IP, MAC,
Master, Backup Master, Slave, and Total.

Current Array This table displays all the current array members. The
Members: DAP-2360 AP array feature supports up to eight AP
array members.



Wireless Basic Settings
Network Name Select this option to use a Network Name (SSID).
(SSID):

SSID Visibility: Select this option to enable SSID Visibility.

Auto Channel Select this option to use Auto Channel Selection.
Selection:

Channel Width: Select this option to specify the Channel Width.

Security: Select this option to use Wireless Security.

Wireless Advanced Settings
Data Rate: Select this option to specify the Data Rate.

Beacon Interval: Select this option to specify the Beacon Interval.

DTIM Interval: Select this option to specify the DTIM Interval.

Transmit Power: Select this option to specify the Transmit Power.

WMM (Wi-Fi Select this option to use WMM.
Multimedia):

Ack Time Out: Select this option to use Ack Time Out.

Short GI: Select this option to use a Short GI.

IGMP Snooping: Select this option to enable IGMP Snooping.

Link Integrity: Select this option to use Link Integrity.

Connection Limit: Select this option to use a Connection Limit.

Wireless ACL: Select this option to use Wireless ACL.



Multiple SSID & VLAN
SSID: Select this option to use an SSID.

SSID Visibility: Select this option to make the SSID Visible.

Security: Select this option to use Wireless Security.

WMM: Select this option to use WMM.

VLAN: Select this option to use VLAN.

Advanced Functions
Schedule Settings: Select this option to use Scheduled Settings.

QoS Settings: Select this option to use Quality of Service.

DHCP Server Settings: Select this option to use DHCP.

Log Settings: Select this option to enable the Log Settings.

Time and Date Settings: Select this option to use the Time and Date Settings.

Administration Settings
SNMP Settings: Select this option to enable SNMP Settings.

System Name Settings: Select this option to use a System Name.

Login Settings: Select this option to use Login Settings.

Console Settings: Select this option to enable Console Settings.



ARP Spoofing Prevention
The ARP Spoofing Prevention feature allows users to add IP/MAC address mapping to prevent ARP spoofing attack.

ARP Spoofing Prevention: This check box allows you to enable
the ARP spoofing prevention
function.

Gateway IP Address: Enter a gateway IP address.

Gateway MAC Address: Enter a gateway MAC address.



DHCP Server
Dynamic Pool Settings
The DHCP address pool defines the range of the IP address that can be assigned to stations in the network. A Dynamic
Pool allows wireless stations to receive an available IP with lease time control. If needed or required in the network,
the DAP-2360 is capable of acting as a DHCP server.

Function Enable/ Dynamic Host Configuration Protocol (DHCP)
Disable: assigns dynamic IP addresses to devices on
the network. This protocol simplifies network
management and allows new wireless devices
to receive IP addresses automatically without
the need to manually assign new IP addresses.
Select Enable to allow the DAP-2360 to function
as a DHCP server.

IP Assigned Input the first IP address available for assignment
From: on your network.

The Range of Enter the number of IP addresses available for
Pool (1-254): assignment. IP addresses are increments of the
IP address specified in the “IP Assigned From”
field.

Subnet Mask: All devices in the network must have the
same subnet mask to communicate. Enter the
submask for the network here.

Gateway: Enter the IP address of the gateway on the
network.

WINS: Specify the Windows Internet Naming Service (WINS) server address for the wireless network. WINS is a system that
determines the IP address of a network computer that has a dynamically assigned IP address.



DNS: Enter the IP address of the Domain Name System (DNS) server. The DNS server translates domain names such as
www.dlink.com into IP addresses.

Domain Name: Enter the domain name of the network, if applicable. (An example of a domain name is: www.dlink.com.)

Lease Time The lease time is the period of time before the DHCP server will assign new IP addresses.
(60-31536000 sec):



Static Pool Setting
The DHCP address pool defines the range of IP addresses that can be assigned to stations on the network. A static
pool allows specific wireless stations to receive a fixed IP without time control.

Function Enable/ Dynamic Host Configuration Protocol
Disable: (DHCP) assigns IP addresses to wireless
devices on the network. This protocol
simplifies network management and allows
new wireless devices to receive IP addresses
automatically without the need to manually
assign IP addresses. Select Enable to allow
the DAP-2360 to function as a DHCP server.

Assigned IP: Use the Static Pool Settings to assign the
same IP address to a device every time you
start up. The IP addresses assigned in the
Static Pool list must NOT be in the same IP
range as the Dynamic Pool. After you have
assigned a static IP address to a device via
its MAC address, click Save; the device will
appear in the Assigned Static Pool at the
bottom of the screen. You can edit or delete
the device in this list.

Assigned MAC Enter the MAC address of the device
Address: requesting association here.

Subnet Mask: Define the submask of the IP address specified in the “IP Assigned From” field.



Gateway: Specify the Gateway address for the wireless network.

WINS: Specify the Windows Internet Naming Service (WINS) server address for the wireless network. WINS is a system that
determines the IP address of a network computer with a dynamically assigned IP address, if applicable.

DNS: Enter the Domain Name System (DNS) server address for the wireless network. The DNS server translates domain names
such as www.dlink.com into IP addresses.

Domain Name: Specify the domain name for the network.



Current IP Mapping List
This window displays information about the current assigned DHCP dynamic and static IP address pools. This information
is available when you enable DHCP server on the AP and assign dynamic and static IP address pools.

Current DHCP These are IP address pools the DHCP server
Dynamic Profile: has assigned using the dynamic pool setting.

Host Name: The host name of a device on the network
that is assigned an IP address from the DHCP
dynamic pool.

Binding MAC The MAC address of a device on the network
Address: that is assigned an IP address from the DHCP
dynamic pool.

Assigned IP The current corresponding DHCP-assigned IP
Address: address of the device.

Lease Time: The length of time that the dynamic IP address
will be valid.

Current DHCP These are the IP address pools of the DHCP
Static Pools: server assigned through the static pool
settings.

Host Name: The host name of a device on the network that
is assigned an IP address from the DHCP dynamic pool.

Binding MAC The MAC address of a device on the network that is within the DHCP static IP address pool.
Address:

Assigned IP The current corresponding DHCP-assigned static IP address of the device.
Address:



Filters
Wireless MAC ACL
Wireless Band: Displays the current wireless band rate.

Access Control Select Disable to disable the filters function.
List:

Select Accept to accept only those devices
with MAC addresses in the Access Control
List. All other devices not on the list will be
rejected.

Select Reject to reject the devices with MAC
addresses on the Access Control List. All
other devices not on the list will be accepted.

MAC Address: Enter each MAC address that you wish to
include in your filter list, and click Add.

MAC Address List: When you enter a MAC address, it appears
in this list. Highlight a MAC address and click
Delete to remove it from this list.

Upload ACL File: You may create an ACL list and upload it to
the access point instead of manually entering
the information. Once created, click the
Browse button and locate your file. Select it
and then click Upload.

Download ACL Click Download to export the ACL to a file
File: on your computer.



WLAN Partition
Wireless Band: Displays the current wireless band rate.

Link Integrity: Select Enable or Disable.

Ethernet to The default is Enable. When disabled, all
WLAN Access: data from the Ethernet to associated wireless
devices will be blocked. Wireless devices can
still send data to the Ethernet.

Internal Station The default value is Enable, which allows
Connection: stations to inter-communicate by connecting
to a target AP. When disabled, wireless
stations cannot exchange data through the
AP.



Status
Device Information
Device This read-only window displays the configuration
Information: settings of the DAP-2360, including the firmware
version and the device's MAC address.



Client Information
Client Information: This window displays the wireless client
information for clients currently connected
to the DAP-2360.

The following information is available for each
client communicating with the DAP-2360.

SSID: Displays the SSID of the client.

MAC: Displays the MAC address of the client.

Band: Displays the wireless band that the client
is connected to.

Authentication: Displays the type of authentication being
used.

Signal: Displays the client's signal strength.

Power Saving Displays the status of the power saving
Mode: feature.



WDS Information
WDS This window displays the Wireless
Information: Distribution System information for clients
currently connected to the DAP-2360.

The following information is available for each
client communicating with the DAP-2360.

Name: Displays the SSID of the client.

MAC: Displays the MAC address of the client.

Authentication: Displays the type of authentication being
used.

Signal: Displays the client's signal strength.

Status: Displays the status of the power saving
feature.



Stats
Ethernet
Ethernet Traffic This page displays transmitted and received
Statistics: count statistics for packets and bytes.



WLAN Traffic
WLAN Traffic This page displays wireless network statistics
Statistics: for data throughput, transmitted and received
frames, and frame errors.



Log
View Log
View Log: The AP’s embedded memory displays
system and network messages including
a time stamp and message type. The log
information includes but is not limited to the
following items: cold start AP, upgrading
firmware, client associate and disassociate
with AP, and web login. The web page holds
up to 500 logs.



Log Settings
Log Server/IP Enter the IP address of the server you would
Address: like to send the DAP-2360 log to.

Log Type: Check the box for the type of activity you
want to log. There are three types: System
Activity, Wireless Activity, and Notice.

Email Notification: Check to enable Email notification.

Outgoing Mail Select the SMTP server from the drop-down
Server (SMTP): menu.

Authentication: Check to enable authentication.

SSL / TLS: Check to enable SSL/TLS authentication.

From Email Enter the “From” email address.
Address:

To Email Address: Enter the destination email address.

Email Server Enter the Email Server Address.
Address:

SMTP Port: Enter the SMTP port.

Username: Enter your email username.

Password: Enter your email password.

Confirm Password: Enter your email password again.

Schedule: Select when to send the log to your email
(in hours). You will receive an email when
the log is full too.


Maintenance
Administration Settings
Check one or more of the five main categories to display the various hidden administrator parameters and settings
displayed on the next five pages.



Limit Administrator
Each of the five main categories display various hidden administrator parameters and settings.
Limit Check the box provided and the enter the
Administrator specific VLAN ID that the administrator will
VLAN ID: be allowed to log in from.

Limit Check to enable the Limit Administrator IP
Administrator IP: address.

IP Range: Enter the IP address range that the
administrator will be allowed to log in from
and then click the Add button.



System Name Settings
System Name: The name of the device. The default name is
D-Link DAP-2360.

Location: The physical location of the device, e.g. 72nd
Floor, D-Link HQ.



Login Settings

Login Name: Enter a user name. The default is admin.

Old Password: When changing your password, enter the old
password here.

New Password: When changing your password, enter the new
password here. The password is case-sensitive.
“A” is a different character than “a.” The length
should be between 0 and 12 characters.

Confirm Enter the new password a second time for
Password: confirmation purposes.



Console Settings

Status: Status is enabled by default. Uncheck the box
to disable the console.

Console Select the type of protocol you would like to
Protocol: use, Telnet or SSH.

Timeout: Set to 1 Min, 3 Mins, 5 Mins, 10 Mins, 15
Mins or Never.



SNMP Settings

Status: Check the box to enable the SNMP
functions. This option is disabled
by default.

Public Community String: Enter the public SNMP community
string.

Private Community String: Enter the private SNMP community
string.

Trap Status: Check the box to enable Trap
Status.

Trap Server IP: Enter the Trap Server IP address.



Firmware and SSL Certification Upload
This page allows the user to perform a firmware upgrade. A Firmware upgrade is a function that upgrade the running
software used by the access point. This is a useful feature that prevents future bugs and allows for new features to
be added to this product. Please go to your local D-Link website to see if there is a newer version firmware available.

Upload Firmware The current firmware version is displayed
From Local Hard above the file location field. After downloading
Drive: the most recent version of firmware for the
DAP-2360 from http://support.dlink.com to
your local computer, use the Browse button to
locate the firmware file on your computer. Click
Upload to update the firmware version. Please
don’t turn the power off while upgrading.

Language Pack You may load a language pack to display the
Upgrade: utility in another language. Click Browse to
locate the language pack file on your local
computer. After selecting and opening the
file, click Upload to upload the file to the
DAP-2360.

Upload SSL Click Browse to locate the SSL Certification
Certification file on your local computer. After selecting and
From Local Hard opening the file, click Upload to upload the file
Drive: to the DAP-2360.



Configuration File Upload
Upload File: Click the Browse button to locate a previously
saved configuration file on your local computer.
After selecting the file, click Upload to apply
the configuration settings to the DAP-2360.

Download Click Download to save the current
Configuration DAP-2360 configuration to your local computer.
File: Note that if you save one configuration with
the administrator’s password now, after
resetting your DAP-2360, and then updating
to this saved configuration file, the password
will be gone.



Time and Date
Current Time: Displays the current time and date settings.

Time Zone: Use the drop-down menu to select your
correct Time Zone.

Enable Daylight Check the box to Enable Daylight Saving
Saving: Time.

Daylight Saving Use the drop-down menu to select the correct
Dates: Daylight Saving offset.

Enable NTP Check to enable the AP to get system time
Server: from an NTP server.

NTP Server: Enter the NTP server IP address.

Set the Date and You can either manually set the time for your
Time Manually: AP here, or you can click the Copy Your
Computer’s Time Settings button to copy
the time from the computer you are using
(Make sure that the computer’s time is set
correctly).



System
System Settings
Restart the Device: Click Restart to restart the DAP-2360.

Restore to Factory Click Restore to restore the DAP-2360
Default Settings: back to factory default settings.

Clear Language Pack: Click Clear to remove any loaded
language packs.



Help
Help: Scroll down the Help page for topics and
explanations.


Section 6 - Troubleshooting

Troubleshooting
This chapter provides solutions to problems that can occur during the installation and operation of the DAP-2360.
Read the following descriptions if you are having problems. (The examples below are illustrated in Windows® XP. If
you have a different operating system, the screenshots on your computer will look similar to the following examples.)

1. Why can’t I access the web-based configuration utility?

When entering the IP address of the D-Link access point (192.168.0.50 for example), you are not connecting to a
website on the Internet nor do you have to be connected to the Internet. The device has the utility built-in to a ROM
chip in the device itself. Your computer must be on the same IP subnet to connect to the web-based utility.

• Make sure you have an updated Java-enabled web browser. We recommend the following:

- Microsoft Internet Explorer® 6.0 and higher
- Mozilla Firefox 3.0 and higher
- Google™ Chrome 2.0 and higher
- Apple Safari 3.0 and higher

• Verify physical connectivity by checking for solid link lights on the device. If you do not get a solid link light, try using
a different cable or connect to a different port on the device if possible. If the computer is turned off, the link light may
not be on.

• Disable any internet security software running on the computer. Software firewalls such as Zone Alarm, Black Ice,
Sygate, Norton Personal Firewall, and Windows® XP firewall may block access to the configuration pages. Check the
help files included with your firewall software for more information on disabling or configuring it.


Section 6 - Troubleshooting

• Configure your Internet settings:

• Go to Start > Settings > Control Panel. Double-click the Internet Options Icon. From the Security tab,
click the button to restore the settings to their defaults.

• Click the Connection tab and set the dial-up option to Never Dial a Connection. Click the LAN Settings
button. Make sure nothing is checked. Click OK.

• Go to the Advanced tab and click the button to restore these settings to their defaults. Click OK three
times.

• Close your web browser (if open) and open it.

• Access the web management. Open your web browser and enter the IP address of your D-Link access point in the
address bar. This should open the login page for your the web management.

• If you still cannot access the configuration, unplug the power to the access point for 10 seconds and plug back in.
Wait about 30 seconds and try accessing the configuration. If you have multiple computers, try connecting using a
different computer.

2. What can I do if I forgot my password?

If you forgot your password, you must reset your access point. Unfortunately, this process will change all your settings
back to the factory defaults.

To reset the access point, locate the reset button (hole) on the rear panel of the unit. With the access point powered
on, use a paperclip to hold the button down for 10 seconds. Release the button and the access point will go through
its reboot process. Wait about 30 seconds to access the access point. The default IP address is 192.168.0.50. When
logging in, the username is admin and leave the password box empty.


Appendix B - Networking Basics

Networking Basics
Check your IP address
After you install your network adapter, by default, the TCP/IP settings should be set to obtain an IP address from a
DHCP server (i.e. wireless router) automatically. To verify your IP address, please follow the steps below.

Click on Start > Run. In the run box type cmd and click OK.

At the prompt, type ipconfig and press Enter.

This will display the IP address, subnet mask, and
the default gateway of your adapter.

If the address is 0.0.0.0, check your adapter
installation, security settings, and the settings on
your router. Some firewall software programs may
block a DHCP request on newly installed adapters.

If you are connecting to a wireless network at a
hotspot (e.g. hotel, coffee shop, airport), please
contact an employee or administrator to verify their
wireless network settings.



Statically Assign an IP address
If you are not using a DHCP capable gateway/router, or you need to assign a static IP address, please follow the steps
below:

Step 1
Windows® 2000: Click on Start > Settings > Control Panel > Network Connections
Windows® XP: Click on Start > Control Panel > Network Connections
Windows Vista®: Click on Start > Control Panel > Network and Internet > Network and Sharing Center > Manage
network connections

Step 2
Right-click on the Local Area Connection which represents your network adapter and select Properties.

Step 3
Highlight Internet Protocol (TCP/IP) and click Properties.

Step 4
Click Use the following IP address and enter an IP address that is on the same subnet as your network or the
LAN IP address on your router.

Example: If the router’s LAN IP address is 192.168.0.1, make your IP address 192.168.0.X where X is a number
between 2 and 99. Make sure that the number you choose is not in use on the network. Set Default Gateway the
same as the LAN IP address of your router (192.168.0.1).



Set Primary DNS the same as the LAN IP address of your router
(192.168.0.1). The Secondary DNS is not needed or you may
enter a DNS server from your ISP.

Step 5
Click OK twice to save your settings.


Appendix C - Technical Specifications

Technical Specifications
Standards • 802.1x
• IEEE 802.11b • WEP™ 64-/128-bit
• IEEE 802.11g • SSID Broadcast Disable
• IEEE 802.11n • MAC Address Access Control
• IEEE 802.3
• IEEE 802.3u Wireless Frequency Range
• IEEE 802.3ab • 2.4 to 2.4835 GHz**
• IEEE 802.3af
Operating Voltage
Network Management
• Web Browser interface • 48V DC +/- 10% for PoE or 5V/2.5A
HTTP Radio and Modulation Type
Secure HTTP (HTTPS) For 802.11g/n:
• AP Manager II BPSK, QPSK, 16QAM, and 64QAM with OFDM
• SNMP Support For 802.11b:
D-View Module DQPSK, DBPSK, DSSS, and CCK
Private MIB
• Command Line Interface
Operating Frequency**
Telnet
For 802.11b/g:
Secure SSH Telnet
2.4 ~ 2.4835 GHz
Data Rates* For 802.11n:
For 802.11b: 2.4 GHz Band: 2.4 ~ 2.4835 GHz
• 11, 5.5, 2, and 1 Mbps
For 802.11g: Dipole Antenna
• 54, 48, 36, 24, 18, 12, 9, and 6 Mbps • 5dBi Gain @2.4 GHz
For 802.11n:
HT20/HT40
• 144.4/300, 130/270, 117/243, 104/216, 78/162, 66/135, 58.5/121.5, Transmit Output Power (at Antenna Connector)
52/108, 39/81, 26/54, 19.5/40.5, 12/27, and 6.5/13.5 Mbps • 23dBm @ 2.4GHz
Security
• WPA™ Personal/Enterprise Max Power Consumption
• WPA2™ Personal/Enterprise • Max. 8W with 5V/DC
• Max. 9W with PoE

* aximum wireless signal rate derived from IEEE Standard 802.11g and 802.11n specifications. Actual data throughput will vary. Network conditions and environmental
M
factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate. Environmental factors will
adversely affect wireless signal range.


Appendix C - Technical Specifications

LEDs
• Power
• LAN
• 2.4 GHz

Temperature
• Operating: 0˚C to 40˚C
• Storing: -20˚C to 65˚C

Humidity
• Operating: 10%~90% (non-condensing)
• Storing: 5%~95% (non-condensing)

Certifications
• FCC Class B
• CE
• IC
• C-Tick
• UL
®
• WiFi

Dimensions
• L = 188 mm
• W = 166 mm
• H = 37 mm

**Please note that operating frequency ranges vary depending on the regulations of individual countries and jurisdictions.


Trademarks:
D-Link Networking is a registered trademark of D-Link Corporation/D-Link Systems, Inc. Other trademarks or registered trademarks are
the property of their respective owners.

Copyright Statement:
No part of this publication or documentation accompanying this product may be reproduced in any form or by any means or used to make
any derivative such as translation, transformation, or adaptation without permission from D-Link Corporation/D-Link Systems, Inc., as
stipulated by the United States Copyright Act of 1976 and any amendments thereto. Contents are subject to change without prior notice.

Copyright ©2008-2010 by D-Link Corporation/D-Link Systems, Inc. All rights reserved.

CE Mark Warning:
This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required
to take adequate measures.

FCC Statement:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
For detailed warranty information applicable to products purchased outside the United States, please contact the corresponding local
D-Link office.

FCC Caution:
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate
this equipment.


This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.

IMPORTANT NOTICE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed
and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at
the factory to match the intended destination. The firmware setting is not accessible by the end user.
For detailed warranty information applicable to products purchased outside the United States, please contact the corresponding local
D-Link office.

IC statement
This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.

IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed
and operated with minimum distance 20cm between the radiator & your body.

This device has been designed to operate with an antenna having a maximum gain of 5dB. Antenna having a higher gain is strictly prohibited
per regulations of Industry Canada. The required antenna impedance is 50 ohms.


Acces Point Dap 2360 - Manual

More Related Content

What's hot (12)

Similar to Acces Point Dap 2360 - Manual (20)

More from Nikoroso (20)

Recently uploaded (20)

Acces Point Dap 2360 - Manual