John deere ja62 21 inch walk-behind mower service repair manual

TECHNICAL
MANUAL
Litho in U.S.A
John Deere
Worldwide Commercial and
Consumer Equipment Division
TM1723 (Mar01)
Replaces TM1723 (15Oct97)
JA60, JA62, JA65,
JE75, JX75, and JX85
21-Inch Walk-Behind
Mower (Cast Deck)

M88849
21” Walk-Behind Mower (Cast Deck)

INTRODUCTION
3/30/01 1 - 1
This technical manual is written for an experienced
technician and contains sections that are specifically for
this product. It is a part of a total product support
program.
The manual is organized so that all the information on a
particular system is kept together. The order of grouping
is as follows:
• Table of Contents
• General Diagnostic Information
• Specifications
• Electrical Wiring Harness Legend
• Component Location
• System Schematic
• Wiring Harness
• Troubleshooting Chart
• Theory of Operation
• Diagnostics
• Tests & Adjustments
• Repair
Note: Depending on the particular section or system
being covered, not all of the above groups may be
used.
Each section will be identified with a symbol rather than a
number. The groups and pages within a section will be
consecutively numbered.
We appreciate your input on this manual. To help, there
are postage paid post cards included at the back. If you
find any errors or want to comment on the layout of the
manual please fill out one of the cards and mail it back to
us.
All information, illustrations and
specifications in this manual are based on
the latest information available at the time of
publication. The right is reserved to make
changes at any time without notice.
COPYRIGHT© 2001
Deere and Co.
John Deere Worldwide Commercial and
Consumer Equipment Division
Horicon, WI
All rights reserved
Information
Specifications and
Engine - B&S Quantum
Safety
Miscellaneous
Power Train
Engine - Kawasaki
Electrical
Engine - B&S Intek

SAFETY
1 - 2 3/30/01
Handle Fluids Safely-Avoid Fires
Be Prepared For Emergencies
When you work around fuel, do not smoke or work near
heaters or other fire hazards.
Store flammable fluids away from fire hazards. Do not
incinerate or puncture pressurized containers.
Make sure machine is clean of trash, grease, and
debris.
Do not store oily rags; they can ignite and burn
spontaneously.
Be prepared if a fire starts.
Keep a first aid kit and fire extinguisher handy.
Keep emergency numbers for doctors, ambulance
service, hospital, and fire department near your
telephone.
Wear Protective Clothing
Wear close fitting clothing and safety equipment
appropriate to the job.
Prolonged exposure to loud noise can cause
impairment or loss of hearing. Wear a suitable hearing
protective device such as earmuffs or earplugs to
protect against objectionable or uncomfortable loud
noises.
Recognize Safety Information
This is the safety-alert symbol. When you see this
symbol on your machine or in this manual, be alert to
the potential for personal injury.
Follow recommended precautions and safe servicing
practices.
Understand Signal Words
A signal word—DANGER, WARNING, or CAUTION—is
used with the safety-alert symbol. DANGER identifies
the most serious hazards.
DANGER or WARNING safety signs are located near
specific hazards. General precautions are listed on
CAUTION safety signs. CAUTION also calls attention
to safety messages in this manual.
Replace Safety Signs
Replace missing or damaged safety signs. See the
machine operator’s manual for correct safety sign
placement.
WARNING: California Proposition 65
Warning
Gasoline engine exhaust from this product contains
chemicals known to the State of California to cause
cancer, birth defects, or other reproductive harm.

SAFETY
3/30/01 1 - 3
Operating equipment safely requires the full attention
of the operator. Do not wear radio or music
headphones while operating machine.
Service Machines Safely
Tie long hair behind your head. Do not wear a necktie,
scarf, loose clothing, or necklace when you work near
machine tools or moving parts. If these items were to
get caught, severe injury could result.
Remove rings and other jewelry to prevent electrical
shorts and entanglement in moving parts.
Use Proper Tools
Use tools appropriate to the work. Makeshift tools and
procedures can create safety hazards. Use power tools
only to loosen threaded parts and fasteners. For
loosening and tightening hardware, use the correct size
tools. DO NOT use U.S. measurement tools on metric
fasteners. Avoid bodily injury caused by slipping
wrenches. Use only service parts meeting John Deere
specifications.
Park Machine Safely
Before working on the machine:
1. Lower all equipment to the ground.
2. Stop the engine and remove the key.
3. Hang a “DO NOT OPERATE” tag in operator
station.
Support Machine Properly And Use
Proper Lifting Equipment
If you must work on a lifted machine or attachment,
securely support the machine or attachment.
Do not support the machine on cinder blocks, hollow
tiles, or props that may crumble under continuous load.
Do not work under a machine that is supported solely
by a jack. Follow recommended procedures in this
manual.
Lifting heavy components incorrectly can cause severe
injury or machine damage. Follow recommended
procedure for removal and installation of components
in the manual.
Avoid Injury From Rotating Blades
and PTO Shafts
Keep hands and feet away while machine is running.
Shut off power to service, lubricate or remove mower
blades or PTO shafts.
Work In Clean Area
Before starting a job:
1. Clean work area and machine.
2. Make sure you have all necessary tools to do your
job.
3. Have the right parts on hand.
4. Read all instructions thoroughly; do not attempt
shortcuts.
Using High Pressure Washers
Directing pressurized water at electronic/electrical
components or connectors, bearings, or other sensitive
parts and components may cause product
malfunctions. Reduce pressure and spray at a 45 to 90
degree angle.
Illuminate Work Area Safely
Illuminate your work area adequately but safely. Use a
portable safety light for working inside or under the
machine. Make sure the bulb is enclosed by a wire
cage. The hot filament of an accidentally broken bulb
can ignite spilled fuel or oil.

SAFETY
1 - 4 3/30/01
Work In Ventilated Area
Engine exhaust fumes can cause sickness or death. If
it is necessary to run an engine in an enclosed area,
remove the exhaust fumes from the area with an
exhaust pipe extension.
If you do not have an exhaust pipe extension, open the
doors and get outside air into the area.
Remove Paint Before Welding Or
Heating
Avoid potentially toxic fumes and dust. Hazardous
fumes can be generated when paint is heated by
welding, soldering, or using a torch. Do all work outside
or in a well ventilated area. Dispose of paint and
solvent properly. Remove paint before welding or
heating: If you sand or grind paint, avoid breathing the
dust. Wear an approved respirator. If you use solvent or
paint stripper, remove stripper with soap and water
before welding. Remove solvent or paint stripper
containers and other flammable material from area.
Allow fumes to disperse at least 15 minutes before
welding or heating.
Avoid Harmful Asbestos Dust
Avoid breathing dust that may be generated when
handling components containing asbestos fibers.
Inhaled asbestos fibers may cause lung cancer.
Components in products that may contain asbestos
fibers are brake pads, brake band and lining
assemblies, clutch plates, and some gaskets. The
asbestos used in these components is usually found in
a resin or sealed in some way. Normal handling is not
hazardous as long as airborne dust containing
asbestos is not generated.
Avoid creating dust. Never use compressed air for
cleaning. Avoid brushing or grinding material
containing asbestos. When servicing, wear an
approved respirator. A special vacuum cleaner is
recommended to clean asbestos. If not available, apply
a mist of oil or water on the material containing
asbestos. Keep bystanders away from the area.
Handle Chemical Products Safely
Direct exposure to hazardous chemicals can cause
serious injury. Potentially hazardous chemicals used
with John Deere equipment include such items as
lubricants, coolants, paints, and adhesives.
A Material Safety Data Sheet (MSDS) provides specific
details on chemical products: physical and health
hazards, safety procedures, and emergency response
techniques. Check the MSDS before you start any job
using a hazardous chemical. That way you will know
exactly what the risks are and how to do the job safely.
Then follow procedures and recommended equipment.
Dispose of Waste Properly
Improperly disposing of waste can threaten the
environment and ecology. Potentially harmful waste
used with John Deere equipment include such items as
oil, fuel, coolant, brake fluid, filters, and batteries. Use
leakproof containers when draining fluids. Do not use
food or beverage containers that may mislead
someone into drinking from them. Do not pour waste
onto the ground, down a drain, or into any water
source. Inquire on the proper way to recycle or dispose
of waste from your local environmental or recycling
center, or from your John Deere dealer.
Live With Safety
Before returning machine to customer, make sure
machine is functioning properly, especially the safety
systems. Install all guards and shields.

SPECIFICATIONS AND INFORMATION CONTENTS
CONTENTS
3/30/01 2 - 1
Page
GENERAL VEHICLE SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . 3
ENGINE SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
ELECTRICAL SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
FUEL SYSTEM SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
TRANSMISSION SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
TORQUE SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
INCH FASTENER TORQUE VALUES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
METRIC FASTENER TORQUE VALUES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
LUBRICANTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
GASOLINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
GASOLINE STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
ENGINE OIL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
ENGINE BREAK–IN OIL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
TRANSAXLE OIL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
ANTI-CORROSION GREASE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
ALTERNATIVE LUBRICANTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
SYNTHETIC LUBRICANTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
LUBRICANT STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
MIXING OF LUBRICANTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
CHASSIS GREASE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
OIL FILTERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
PRODUCT IDENTIFICATION LOCATIONS . . . . . . . . . . . . . . . . . . . . . . 11

3/30/01 2 - 3
SPECIFICATIONS & INFORMATION GENERAL MOWER SPECIFICATIONS
GENERAL MOWER SPECIFICATIONS
ENGINE SPECIFICATIONS
Product JA60/JA62/JA65 JA60/JA62/JA65 JE75 JX75/JX85
Manufacturer Briggs & Stratton Briggs & Stratton Kawasaki Kawasaki
Engine Model 12J802 (Quantum) 121602 (Intek) FC150V-ES20 FC150V-HS00 (JX75)
FC150V-GS07 (JX85)
Type 4-cycle gas/Air cooled 4-cycle gas/Air cooled 4-cycle gas/Air cooled 4-cycle gas/Air cooled
Cylinders 1 1 1 1
Valves Side valves Overhead Overhead Overhead
Displacement 190 cc (11.56 cu. in.) 190 cc (11.56 cu. in.) 153 cc (9.34 cu. in.) 153 cc (9.34 cu. in.)
Horsepower 4.5 kW (6 HP) 4.8 kW (6.5 HP) 4.1 kW (5.5 HP) 4.1 kW (5.5 HP)
Lubrication Splash Splash Pressure Pressure
Oil filter N/A N/A N/A Replaceable
(JX85 Only)
Oil Capacity 0.65 L (22.0 oz) 0.65 L (22.0 oz) 0.6 L (20.0 oz) 0.66 L (22.0 oz) w/filter
Throttle Control Variable speed Variable Speed Variable speed Variable speed
Slow Idle Speed 1500 ± 100 rpm 1500 ± 100 rpm 1550 ± 100 rpm 1550 ± 100 rpm
Fast Idle Speed 3200 ± 100 rpm 3200 ± 100 rpm 3125 ± 75 rpm 3125 ± 75 rpm
Carburetor CARB/EPA Certified CARB/EPA Certified CARB/EPA Certified CARB/EPA Certified
Choke Primer bulb Primer bulb Manual Manual
Cooling system Air Air Air Air
Air cleaner Dry replaceable single
element
Dry replaceable dual
element
element
element
ELECTRICAL
SPECIFICATIONS
Ignition Electronic Electronic Capacitive discharge Capacitive discharge
Ignition Coil Air Gap 0.15 – 0.25 mm
(0.006 – 0.010 in.)
0.15 – 0.36 mm
(0.006 – 0.014 in.)
0.30 mm (0.012 in.) 0.30 mm (0.012 in.)
Spark Plug
(resistor)
RCJ8 Champion RC12YC Champion RJ19LM Champion RJ19LM Champion
Spark Plug Gap 0.76 mm (0.030 in.) 0.51 mm (0.020 in.) 0.710 – 0.084 mm
(0.028 – 0.033 in.)
0.710 – 0.084 mm
(0.028 – 0.033 in.)
FUEL SYSTEM
SPECIFICATIONS
Fuel type Unleaded gasoline Unleaded gasoline Unleaded gasoline Unleaded gasoline
Capacity 1.5 L (1.6 U.S. qt) 1.5 L (1.6 U.S. qt) 1.3 L (1.4 U.S. qt) 1.3 L (1.4 U.S. qt)
TRANSMISSION
SPECIFICATIONS
Make Kanzaki Tuff Torq Kanzaki Tuff Torq Kanzaki Tuff Torq Kanzaki Tuff Torq
Type Two or Five Speed Two or Five Speed Five Speed Five Speed
Drive belt 3L – 861.0 mm (33.90
in.)
3L – 861.0 mm (33.90
in.)
3L – 861.0 mm (33.90
in.)
3L – 861.0 mm (33.90
in.)
Transaxle Fully enclosed; grease Fully enclosed; grease Fully enclosed; grease Fully enclosed; grease
Gear selection 2 or 5 Forward
(except JA60 - Push)
2 or 5 Forward
(except JA60 - Push)
5 Forward 5 Forward
Brake Blade brake (clutch) Blade brake (clutch) Blade brake (clutch) Blade brake (clutch)
DIMENSIONS
Tire & Wheel Size 8.0 x 2.0 8.0 x 2.0 8.0 x 2.0 8.0 x 2.0
Shipping Weight
(Approx.)
(43.0 kg) 95 lb. (44.0 kg) 98 lb. (48.0 kg) 105 lb. (54.0 kg) 120 lb.
1. Specifications and design subject to change without notice.
1

2 - 4 3/30/01
TORQUE SPECIFICATIONS SPECIFICATIONS & INFORMATION
TORQUE SPECIFICATIONS
Briggs & Stratton Engine:
Spark Plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 N•m (180 lb-in.)
Cylinder Head Cap Screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 N•m (140 lb-in.)
Flywheel Nut Torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 N•m (60 lb-ft.)
Intake Manifold Cap Screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.5 N•m (120 lb-in.)
Muffler Shoulder Bolts (6.0 Quantum) . . . . . . . . . . . . . . . . . . . . . . . . . 10 N•m (89 lb-in.)
Muffler Bolts (6.5 Intek) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 N•m (89 lb-in.)
Muffler Cylinder Head Bolts (6.5 Intek) . . . . . . . . . . . . . . . . . . . . . . . 9.6 N•m (85 lb-in.)
Carburetor Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 N•m (89 lb-in.)
Connecting Rod Cap Screw. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.3 N•m (100 lb-in.)
Crankcase Cover Cap Screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.6 N•m (85 lb-in.)
Engine to Housing Cap Screws . . . . . . . . . . . . . . . . . . . . . . .55 ± 14 N•m (40 ± 10 lb-ft)
Kawasaki Engine:
Spark Plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 N•m (180 lb-in.)
Cylinder Head Cap Screw
Initial Torque. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 N•m (159 lb-in.)
Final Torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 N•m (212 lb-in.)
Flywheel Nut Torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 N•m (33 lb-ft.)
Muffler Nuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 N•m (89 lb-in.)
Carburetor Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 N•m (90 lb-in.)
Connecting Rod Cap Screw. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 N•m (106 lb-in.)
Crankcase Cover Cap Screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 N•m (62 lb-in.)
Engine to Housing Cap Screws . . . . . . . . . . . . . . . . . . . . . . .55 ± 14 N•m (40 ± 10 lb-ft)
Rocker Arm Lock Nut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 N•m (62 lb-in.)
Blade and Blade Brake Clutch:
Blade Brake Clutch Release Spring Bracket to Deck. . . . . . . . . . . . . . 11 N•m (97 lb-in.)
Blade Brake Clutch (Center Bolt) . . . . . . . . . . . . . . . . . . . . . .75 ± 14 N•m (55 ± 10 lb-ft)
Mower Blade to Blade Brake Clutch. . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 N•m (55 lb-ft)
Mower Blade to Crankshaft Blade Adaptor (JA60 & JA62 Only)75 ± 14 N•m (55 ± 10 lb-ft)
Cutting Width 53.34 cm (21 inches) 53.34 cm (21 inches) 53.34 cm (21 inches) 53.34 cm (21 inches)
Cutting Height 1.3 – 8.9 cm
(0.5 – 3.5 inches)
1.3 – 8.9 cm
(0.5 – 3.5 inches)
1.3 – 8.9 cm
(0.5 – 3.5 inches)
1.3 – 8.9 cm
(0.5 – 3.5 inches)
Ground Speeds (2-
Speed)
1st - 3.2 kph (2.0 mph)
2nd - 4.8 kph (3.0
mph)
1st - 3.2 kph (2.0 mph)
2nd - 4.8 kph (3.0
mph)
N/A N/A
Ground Speeds (5-
Speed)
1st - 1.9 kph (1.2 mph)
2nd - 2.9 kph(1.8 mph)
3rd - 3.9 kph(2.4 mph)
4th - 4.8 kph(3.0 mph)
5th - 6.6 kph(4.1 mph)
1st - 1.9 kph(1.2 mph)
2nd - 2.9 kph(1.8 mph)
3rd - 3.9 kph(2.4 mph)
4th - 4.8 kph(3.0 mph)
5th - 6.6 kph(4.1 mph)
1st - 1.9 kph(1.2 mph)
2nd - 2.9 kph(1.8 mph)
3rd - 3.9 kph(2.4 mph)
4th - 4.8 kph(3.0 mph)
5th - 6.6 kph(4.1 mph)
1st - 1.9 kph(1.2 mph)
2nd - 2.9 kph(1.8 mph)
3rd - 3.9 kph(2.4 mph)
4th - 4.8 kph(3.0 mph)
5th - 6.6 kph(4.1 mph)

3/30/01 2 - 5
SPECIFICATIONS & INFORMATION INCH FASTENER TORQUE VALUES
DO NOT use these hand torque values if a different
torque value or tightening procedure is given for a
specific application. Torque values listed are for general
use only and include a ±10% variance factor. Check
tightness of fasteners periodically. DO NOT use air
powered wrenches.
Shear bolts are designed to fail under predetermined
loads. Always replace shear bolts with identical grade.
Fasteners should be replaced with the same grade.
Make sure fastener threads are clean and that you
properly start thread engagement. This will prevent
them from failing when tightening.
When bolt and nut combination fasteners are used,
torque values should be applied to the NUT instead of
the bolt head.
Tighten toothed or serrated-type lock nuts to the full
torque value.
a “Lubricated” means coated with a lubricant
such as engine oil, or fasteners with phosphate
and oil coatings. “Dry” means plain or zinc
plated (yellow dichromate - Specification
JDS117) without any lubrication.
b “Grade 2” applies for hex cap screws (not hex
bolts) up to 152 mm (6-in.) long. “Grade 1”
applies for hex cap screws over 152 mm (6-in.)
long, and for all other types of bolts and screws
of any length.
Reference: JDS—G200.
INCH FASTENER TORQUE VALUES
Grade 1 Grade 2b
Grade 5, 5.1 or 5.2 Grade 8 or 8.2
Lubricateda Drya Lubricateda Drya Lubricateda Drya Lubricateda Drya
SIZE N•m lb-ft N•m lb-ft N•m lb-ft N•m lb-ft N•m lb-ft N•m lb-ft N•m lb-ft N•m lb-ft
1/4 3.7 2.8 4.7 3.5 6 4.5 7.5 5.5 9.5 7 12 9 13.5 10 17 12.5
5/16 7.7 5.5 10 7 12 9 15 11 20 15 25 18 28 21 35 26
3/8 14 10 17 13 22 16 27 20 35 26 44 33 50 36 63 46
7/16 22 16 28 20 35 26 44 32 55 41 70 52 80 58 100 75
1/2 33 25 42 31 53 39 67 50 85 63 110 80 120 90 150 115
9/16 48 36 60 45 75 56 95 70 125 90 155 115 175 130 225 160
5/8 67 50 85 62 105 78 135 100 170 125 215 160 215 160 300 225
3/4 120 87 150 110 190 140 240 175 300 225 375 280 425 310 550 400
7/8 190 140 240 175 190 140 240 175 490 360 625 450 700 500 875 650
1 290 210 360 270 290 210 360 270 725 540 925 675 1050 750 1300 975
1-1/8 470 300 510 375 470 300 510 375 900 675 1150 850 1450 1075 1850 1350
1-1/4 570 425 725 530 570 425 725 530 1300 950 1650 1200 2050 1500 2600 1950
1-3/8 750 550 950 700 750 550 950 700 1700 1250 2150 1550 2700 2000 3400 2550
1-1/2 1000 725 1250 925 990 725 1250 930 2250 1650 2850 2100 3600 2650 4550 3350
TS1162
1 or 2b
2
5 5.1 5.2
5
8 8.2
8
No Marks
No Marks
SAE
Grade
and Nut
Markings
SAE
Grade
and Head
Markings

2 - 6 3/30/01
METRIC FASTENER TORQUE VALUES SPECIFICATIONS & INFORMATION
DO NOT use these hand torque values if a different
torque value or tightening procedure is given for a
specific application. Torque values listed are for general
use only and include a ±10% variance factor. Check
tightness of fasteners periodically. DO NOT use air
powered wrenches.
Shear bolts are designed to fail under predetermined
loads. Always replace shear bolts with identical grade.
Fasteners should be replaced with the same grade.
Make sure fastener threads are clean and that you
properly start thread engagement. This will prevent
them from failing when tightening.
When bolt and nut combination fasteners are used,
torque values should be applied to the NUT instead of
the bolt head.
Tighten toothed or serrated-type lock nuts to the full
torque value.
a “Lubricated” means coated with a lubricant
such as engine oil, or fasteners with phosphate
and oil coatings. “Dry” means plain or zinc
plated (yellow dichromate - Specification
JDS117) without any lubrication.
Reference: JDS—G200.
METRIC FASTENER TORQUE VALUES
Class 4.8 Class 8.8 or 9.8 Class 10.9 Class 12.9
Lubricateda Drya Lubricateda Drya Lubricateda Drya Lubricateda Drya
SIZE N•m lb-ft N•m lb-ft N•m lb-ft N•m lb-ft N•m lb-ft N•m lb-ft N•m lb-ft N•m lb-ft
M6 48 3.5 6 4.5 9 6.5 11 8.5 13 9.5 17 12 15 11.5 19 14.5
M8 12 8.5 15 11 22 16 28 20 32 24 40 30 37 28 47 35
M10 23 17 29 21 43 32 55 40 63 47 80 60 75 55 95 70
M12 40 29 50 37 75 55 95 70 110 80 140 105 130 95 165 120
M14 63 47 80 60 120 88 150 110 175 130 225 165 205 150 260 109
M16 100 73 125 92 190 140 240 175 275 200 350 225 320 240 400 300
M18 135 100 175 125 260 195 330 250 375 275 475 350 440 325 560 410
M20 190 140 240 180 375 275 475 350 530 400 675 500 625 460 800 580
M22 260 190 330 250 510 375 650 475 725 540 925 675 850 625 1075 800
M24 330 250 425 310 650 475 825 600 925 675 1150 850 1075 800 1350 1000
M27 490 360 625 450 950 700 1200 875 1350 1000 1700 1250 1600 1150 2000 1500
M30 675 490 850 625 1300 950 1650 1200 1850 1350 2300 1700 2150 1600 2700 2000
M33 900 675 1150 850 1750 1300 2200 1650 2500 1850 3150 2350 2900 2150 3700 2750
M36 1150 850 1450 1075 2250 1650 2850 2100 3200 2350 4050 3000 3750 2750 4750 3500
TS1163
4.8
8.8 9.8
10.9
12.9
5 10
12
Property
Class
and
Head
Markings
Property
Class
and
Nut
Markings
4.8
4.8
5
5
8.8
8.8
9.8
9.8
10.9
10.9 12.9
12.9
12.9
12
1210 10
10
10
10

3/30/01 2 - 7
SPECIFICATIONS & INFORMATION LUBRICANTS
LUBRICANTS
GASOLINE
c CAUTION
Gasoline is HIGHLY FLAMMABLE, handle it with care.
DO NOT refuel machine while:
• indoors, always fill gas tank outdoors;
• machine is near an open flame or sparks;
• engine is running, STOP engine;
• engine is hot, allow it to cool sufficiently first;
• smoking.
Help prevent fires:
• fill gas tank to bottom of filler neck only;
• be sure fill cap is tight after fueling;
• clean up any gas spills IMMEDIATELY;
• keep machine clean and in good repair–free of excess grease, oil, debris, and faulty or damaged
parts;
• any storage of machines with gas left in tank should be in an area that is well ventilated to prevent
possible igniting of fumes by an open flame or spark, this includes any appliance with a pilot light.
To prevent fire or explosion caused by STATIC ELECTRIC DISCHARGE during fueling:
• ONLY use a clean, approved POLYETHYLENE PLASTIC fuel container and funnel WITHOUT any metal
screen or filter.
To avoid engine damage:
• DO NOT mix oil with gasoline;
• ONLY use fresh, clean gasoline;
• fill gas tank at the end of each day's operation to
help prevent condensation from forming inside a
partially filled tank;
• keep up with specified service intervals.
Unleaded gasoline with a minimum octane rating
(antiknock index) of 87 is recommended because it
burns cleaner and leaves less unburned deposits in the
engine combustion chamber.
Use of alternative oxygenated, gasohol blended,
unleaded gasoline is acceptable as long as:
• the ethyl or grain alcohol blends DO NOT exceed
10% by volume or
• methyl tertiary butyl ether (MTBE) blends DO NOT
exceed 15% by volume.
IMPORTANT: DO NOT use METHANOL gasoline
because METHANOL is harmful to the
environment and to your health.
GASOLINE STORAGE
IMPORTANT: Keep all dirt, scale, water or other
foreign material out of gasoline.
Keep gasoline in a safe, protected area and in a clean,
properly marked “UNLEADED GASOLINE” container.
DO NOT use deicers to attempt to remove water from
gasoline. DO NOT depend on fuel filters to remove
water from gasoline. It is recommended that a water
separator be installed in the storage tank outlet.
BE SURE to properly discard unstable or contaminated
gasoline.
Whether the unit is either stored or used during the
winter, it is recommended that you add John Deere
Gasoline Conditioner and Stabilizer (TY15977) or an
equivalent to the gasoline. BE SURE to follow
directions on container and properly discard empty
container.
It is recommended that gasoline be stored ONLY in an
approved POLYETHYLENE PLASTIC container
WITHOUT any metal screen or filter. This will help
prevent any accidental sparks from occurring.
r your customers:
• Module DX,ENOIL in JDS–G135;
• Section 530, Lubricants & Hydraulics, of the
John Deere Merchandise Sales Guide;
NO STATIC ELECTRIC
DISCHARGE
NO SMOKINGNO HOT ENGINESTOP ENGINE
NO OPEN FLAME
OR SPARK

2 - 8 3/30/01
ENGINE OIL SPECIFICATIONS & INFORMATION
ENGINE OIL
Use the appropriate oil viscosity based on the expected
air temperature range during the period between
recommended oil changes. Operating outside of these
recommended oil air temperature ranges may cause
premature engine failure.
The following John Deere oil is PREFERRED:
• TORQ-GARD SUPREME®—SAE 5W-30;
• UNI–GARD™—SAE 5W-30.
The following John Deere oils are also recommended,
based on their specified temperature range:
• TURF–GARD®—SAE 10W-30;
• PLUS–4®—SAE 10W-30;
• TORQ–GARD SUPREME®—SAE 30;
• TORQ–GARD SUPREME®—SAE 10W-30;
• UNI–GARD™—SAE 10W-30;
• UNI–GARD™—SAE 30.
Other oils may be used if above John Deere oils are not
available, provided they meet one of the following
specifications:
• SAE 5W-30—API Service Classification SG or
higher;
• SAE 10W-30—API Service Classification SG or
higher;
• SAE 30—API Service Classification SC or higher.
John Deere Dealers: You may want to cross-reference
the following publications to recommend the proper oil
for your customers:
• Module DX,ENOIL2 in JDS–G135;
• Section 530, Lubricants and Hydraulics, of the John
Deere Merchandise Sales Guide;
• Lubrication Sales Manual PI7032.
ENGINE BREAK–IN OIL
IMPORTANT: ONLY use a quality break-in oil in
rebuilt or remanufactured engines for the first 5
hours (maximum) of operation. DO NOT use oils
with heavier viscosity weights than SAE 5W-30
or oils meeting specifications API SG or SH,
these oils will not allow rebuilt or
remanufactured engines to break-in properly.
The following John Deere oil is PREFERRED:
• John Deere BREAK–IN ENGINE OIL.
John Deere BREAK–IN ENGINE OIL is formulated
with special additives for aluminum and cast iron type
engines to allow the power cylinder components
(pistons, rings, and liners as well) to “wear-in” while
protecting other engine components, valve train and
gears, from abnormal wear. Engine rebuild instructions
should be followed closely to determine if special
requirements are necessary.
John Deere BREAK–IN ENGINE OIL is also
recommended for non-John Deere engines, both
aluminum and cast iron types.
The following John Deere oil is also recommended as
a break-in engine oil:
• TORQ–GARD SUPREME®—SAE 5W-30.
If the above recommended John Deere oils are not
available, use a break-in engine oil meeting the
following specification during the first 5 hours
(maximum) of operation:
• SAE 5W-30—API Service Classification SE or
higher.
• SAE 5W-30—CCMC Specification G4 or higher.
AIR TEMPERATURE M58275
SAE5W-30
PREFERRED
SAE10W-30
SAE30
M58275
BREAK-INOIL
AIR TEMPERATURE
PREFERRED
SAE5W-30

3/30/01 2 - 9
SPECIFICATIONS & INFORMATION TRANSAXLE OIL
IMPORTANT: After the break-in period, use the
John Deere oil that is recommended for this
engine.
for your customers:
• Module DX,ENOIL4 in JDS–G135;
TRANSAXLE OIL
IMPORTANT: DO NOT use engine oil or “Type F”
(Red) Automatic Transmission Fluid in this
transmission. DO NOT mix any other oils in this
transmission. DO NOT use BIO–HY–GARD® in
this transmission.
Use recommended oil viscosity based on the expected
air temperature range during the service interval.
The following John Deere transmission and hydraulic
oil is PREFERRED:
• HY–GARD®—JDM J20C.
Other oils may be used if above recommended John
Deere oil is not available, provided they meet the
following specification:
• John Deere Standard JDM J20C.
IMPORTANT: If minimum air temperature should
fall below -25°C (-13°F), the transmission oil
must be heated to at least five degrees above
the lower limit before start-up or transmission
may be damaged. For prolonged operation
under heavy load in air temperatures above
50°C (122°F) reduce service interval by 50%.
for your customers:
• Module DX,ANTI in JDS–G135;
• Section 530, Lubricants & Hydraulics, of the
John Deere Merchandise Sales Guide;
NOTE: Disregard the John Deere All Weather
Hydrostatic Fluid (JDM J21A) listing—it has
been eliminated from the specification.
AIR TEMPERATURE M58275
JDMJ20C

2 - 10 3/30/01
ANTI-CORROSION GREASE SPECIFICATIONS & INFORMATION
ANTI-CORROSION GREASE
This anti-corrosion grease is formulated to provide the
best protection against absorbing moisture, which is
one of the major causes of corrosion. This grease is
also superior in its resistance to separation and
migration.
The following anti-corrosion grease is PREFERRED:
• DuBois MPG-2® Multi-Purpose Polymer
Grease—M79292.
Other greases may be used if they meet or exceed the
following specifications:
• John Deere Standard JDM J13A2, NLGI Grade 1.
the following publications to recommend the proper
grease for your customers:
• Module DX,GREA1 in JDS–G135;
ALTERNATIVE LUBRICANTS
Conditions in certain geographical areas outside the
United States and Canada may require different
lubricant recommendations than the ones printed in
this technical manual or the operator's manual. Consult
with your John Deere Dealer, or Sales Branch, to
obtain the alternative lubricant recommendations.
IMPORTANT: Use of alternative lubricants could
cause reduced life of the component.
If alternative lubricants are to be used, it is
recommended that the factory fill be thoroughly
removed before switching to any alternative lubricant.
SYNTHETIC LUBRICANTS
Synthetic lubricants may be used in John Deere
equipment if they meet the applicable performance
requirements (industry classification and/or military
specification) as shown in this manual.
The recommended air temperature limits and service
or lubricant change intervals should be maintained as
shown in the operator’s manual.
Avoid mixing different brands, grades, or types of oil.
Oil manufacturers blend additives in their oils to meet
certain specifications and performance requirements.
Mixing different oils can interfere with the proper
functioning of these additives and degrade lubricant
performance.
LUBRICANT STORAGE
All machines operate at top efficiency only when clean
lubricants are used. Use clean storage containers to
handle all lubricants. Store them in an area protected
from dust, moisture, and other contamination. Store
drums on their sides. Make sure all containers are
properly marked as to their contents. Dispose of all old,
used containers and their contents properly.
MIXING OF LUBRICANTS
In general, avoid mixing different brands or types of
lubricants. Manufacturers blend additives in their
lubricants to meet certain specifications and
performance requirements. Mixing different lubricants
can interfere with the proper functioning of these
additives and lubricant properties which will downgrade
their intended specified performance.
JDMJ13A2
NLGIGrade1
M58275AIR TEMPERATURE

3/30/01 2 - 11
SPECIFICATIONS & INFORMATION CHASSIS GREASE
CHASSIS GREASE
Use the following grease based on the air temperature
range. Operating outside of the recommended grease
air temperature range may cause premature failures.
IMPORTANT: ONLY use a quality grease in this
application. DO NOT mix any other greases in
this application. DO NOT use any BIO–GREASE
in this application.
The following John Deere grease is PREFERRED:
• HIGH-TEMPERATURE EP GREASE®—JDM
J13E4, NLGI Grade 2.
• GREASE–GARD™—JDM J13E4, NLGI Grade 2.
Other greases may be used if above preferred John
Deere grease is not available, provided they meet the
following specification:
• John Deere Standard JDM J13E4, NLGI Grade 2.
the following publications to recommend the proper
grease for your customers:
• Module DX,GREA1 in JDS–G135;
• Lubrication Sales Manual P17032.
OIL FILTERS
IMPORTANT: Filtration of oils is critical to proper
lubrication performance. Always change filters
regularly.
The following John Deere oil filters are PREFERRED:
• AUTOMOTIVE AND LIGHT TRUCK ENGINE OIL
FILTERS.
Most John Deere filters contain pressure relief and
anti-drainback valves for better engine protection.
Other oil filters may be used if above recommended
John Deere oil filters are not available, provided they
meet the following specification:
• ASTB Tested In Accordance With SAE J806.
filter for your customers:
• Module DX,FILT in JDS–G135;
• Section 540, Lubricants & Hydraulics, of the John
• Lawn & Grounds Care Tune-Up Guide PI672.
PRODUCT IDENTIFICATION
LOCATIONS
When ordering parts or submitting a warranty claim, it
is IMPORTANT that you include the product
identification number and the component product
identification numbers.
The location of identification numbers and component
product identification numbers are shown.
PRODUCT IDENTIFICATION NUMBER
JDMJ13E4
M58275AIR TEMPERATURE
NLGIGrade2
MX8780

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

2 - 12 3/30/01
PRODUCT IDENTIFICATION LOCATIONS SPECIFICATIONS & INFORMATION
6.0 HP BRIGGS & STRATTON QUANTUM ENGINE
6.5 HP BRIGGS & STRATTON INTEK ENGINE
KAWASAKI ENGINE
M91093
MX8776
M91176

ENGINE - BRIGGS & STRATTON QUANTUM CONTENTS
Page
CONTENTS
3/30/01 3 - 1
SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
ENGINE SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
FUEL SYSTEM SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
ELECTRICAL SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
REPAIR SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
TORQUE SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
SPECIAL EQUIPMENT OR TOOLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
OTHER MATERIALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
COMPONENT LOCATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
ENGINE – WITH FLYWHEEL BRAKE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
ENGINE – WITH BLADE BRAKE CLUTCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
CARBURETOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
ENGINE TROUBLESHOOTING CHART. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
CARBURETION TROUBLESHOOTING CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
ENGINE TROUBLESHOOTING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
THEORY OF OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
COOLING SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
CRANKCASE BREATHER SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
COMPRESSION RELEASE SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
LUBRICATION SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
FUEL SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
IGNITION CIRCUIT OPERATION – JA62 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
IGNITION CIRCUIT OPERATION – JA65 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
CARBURETOR PRIMER CIRCUIT OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
CARBURETOR MAIN CIRCUIT OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
AIR INTAKE SYSTEM OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
GOVERNOR OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
FLYWHEEL BRAKE OPERATION – JA62. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
DIAGNOSIS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
ENGINE TURNS OVER BUT WILL NOT START . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
ENGINE STARTS, THEN STOPS, OR STOPS WHEN HOT. . . . . . . . . . . . . . . . . . . 21
ENGINE USES TOO MUCH OIL OR BLUE EXHAUST SMOKE . . . . . . . . . . . . . . . 22
BLACK EXHAUST SMOKE OR ENGINE FLOODING . . . . . . . . . . . . . . . . . . . . . . . 22
ENGINE SURGES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
ENGINE MISSES/BACKFIRES, OR SPRAYS FUEL OUT OF CARBUETOR INLET23
TESTS AND ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
AUTOMATIC COMPRESSION RELEASE (ACR) TEST . . . . . . . . . . . . . . . . . . . . . . 24
CYLINDER LEAK-DOWN TEST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
VALVE CLEARANCE CHECK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
CRANKCASE BREATHER TEST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
CRANKCASE VACUUM TEST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
THROTTLE CABLE ADJUSTMENT – JA65 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
GOVERNOR ADJUSTMENT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

CONTENTS CONTINUED ENGINE - BRIGGS & STRATTON QUANTUM
3 - 2 3/30/01
Page
ENGINE IDLE ADJUSTMENT – JA62 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
ENGINE FAST IDLE ADJUSTMENT – JA65 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
FLYWHEEL KEY INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
REPAIR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
CARBURETOR REMOVAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
CARBURETOR INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
MUFFLER REMOVAL & INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
THROTTLE CABLE REMOVAL & INSTALLATION – JA65. . . . . . . . . . . . . . . . . . . . 31
FLYWHEEL BRAKE CABLE REMOVAL & INSTALLATION – JA62 . . . . . . . . . . . . . 31
ENGINE COVER REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
FUEL TANK REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
ENGINE BLOWER HOUSING REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
ENGINE BLOWER HOUSING INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
FLYWHEEL REMOVAL AND INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
CYLINDER HEAD REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
CYLINDER HEAD INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
CYLINDER HEAD INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
CRANKCASE BREATHER REMOVAL & INSPECTION. . . . . . . . . . . . . . . . . . . . . . 34
CRANKCASE BREATHER INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
VALVE REMOVAL AND INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
ENGINE REMOVAL & INSTALLATION – JA62 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
ENGINE REMOVAL & INSTALLATION – JA65 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
CRANKCASE COVER REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
CRANKCASE COVER INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
CAMSHAFT INSPECTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
GOVERNOR LEVER REMOVAL & INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . 41
PISTON REMOVAL AND DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
PISTON REMOVAL AND DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
CONNECTING ROD INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
CYLINDER BORE MEASUREMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
CRANKSHAFT REMOVAL AND INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . 43
MAGNETO BEARING REMOVAL AND INSTALLATION . . . . . . . . . . . . . . . . . . . . . 43
VALVE SEAT RECONDITIONING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
VALVE FACE RECONDITIONING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
VALVE SEAT REPLACEMENT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
EXHAUST VALVE GUIDE REPLACEMENT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
RECOIL STARTER REMOVAL & INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . 47
RECOIL STARTER DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
RECOIL STARTER COMPONENT LOCATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

John deere ja62 21 inch walk-behind mower service repair manual

More Related Content

What's hot(20)

Similar to John deere ja62 21 inch walk-behind mower service repair manual(20)

More from fjjsekmsmmes(20)

Recently uploaded(20)

John deere ja62 21 inch walk-behind mower service repair manual