Caterpillar cat 365 b l mh excavator (prefix cty) service repair manual (cty00001 and up)

Service Repair Manual
Models
365B and 365B L MH
EXCAVATOR

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 365B EXCAVATOR CTY
Configuration: 365B L Material Handler CTY00001-UP (MACHINE) POWERED BY 3196 Engine
Disassembly and Assembly
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems
Media Number -RENR1970-10 Publication Date -01/02/2015 Date Updated -16/02/2015
i02789460
Final Drive - Assemble
SMCS - 4050-016
Assembly procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 138-7575 Link Bracket 5
C 140-7642 Duo-Cone Seal Installer As 1
F 1P-1859 Retaining Ring Pliers 1
G 138-7576 Link Bracket 2
H 5P-3931 Anti-Seize Compound 1
J 9S-3263 Thread Lock Compound 1
K 1U-8846 Gasket Sealant 1
1. Make sure that all parts of the final drive are thoroughly clean and free of dirt and debris
prior to assembly.
Note: Check the condition of all the O-ring seals that are used in the final drive. If any of
the seals are worn or damaged, use new parts for replacement.
2. Reassemble the final drive on Tooling (A) .
1/16
365B L Material Handler CTY00001-UP (MACHINE) POWERED BY 3196 Engine(...
2020/11/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

Illustration 1 g00599211
3. Apply Tooling (H) to the surfaces that contact the bearing cones. Install the bearing cone
with a press. Raise the temperature of bearing (50) and install bearing (50) .
4. Apply Tooling (H) to the surfaces that contact pins (49) . Install pins (49) .
5. Apply Tooling (H) to the surfaces that contact bearing cups (48) and (47) . Install bearing
cups (48) and (47) .
2/16
2020/11/26

6. Install bearing (45) and the bearing cone.
7. Attach Tooling (B) and a suitable lifting device to main housing (39) . Install the main
housing on motor housing (44) , as shown.
8. Use the following procedure to determine the bearing preload and the correct number of
shims.
a. Use a depth micrometer in order to measure the step length of the coupling gear (42) .
Take measurements at several different locations around the gear. Compute the
average of the measured dimensions and record the number. Call this dimension (X) .
b. Use a suitable press and a spacer in order to apply a load of 10000 kg (22046 lb) on
the bearings.
c. Rotate the main housing in order to seat the bearing.
d. Reduce the load on the bearings to 3700 ± 370 kg (8157 ± 815 lb).
3/16
2020/11/26

e. Maintain the load on the bearings. Use a depth micrometer and measure the distance
between the top face of motor housing and the bearing cone, as shown. Take this
measurement in several locations around the bearing. Compute the average of the
measured dimensions and record the number. Call this dimension (Y) .
f. Determine the correct thickness of the shim pack that will be installed between the
bearing cone and the coupling gear. The shim pack thickness is equal to dimension
(Y) minus dimension (X) . Tolerance for the shim pack is 0.1 mm (0.003 inch).
Note: If two shims are required, install the thinner shim next to the coupling gear
when the coupling gear is installed.
9. Attach Tooling (B) and a suitable lifting device in order to remove the main housing from
the motor housing.
Note: Refer to Disassembly and Assembly, "Duo-Cone Conventional Seals - Install".
Note: The rubber seals and all surfaces that contact the seals must be clean and dry. After
installation of the seals, apply clean SAE 30 oil on the contact surfaces of the metal seals.
4/16
2020/11/26

10. Use Tooling (C) to install Duo-Cone seal (46) in the main housing.
11. Use Tooling (C) to install Duo-Cone seal (51) in the motor housing.
Note: Make sure that the Duo-Cone seals are not scratched or damaged during the assembly
of the main housing or during the assembly of the motor housing. After installation of the
main housing on the motor housing, there will be a small gap between the components. The
gap is caused by the Duo-Cone seals. The gap will be eliminated during installation of the
gear.
12. Install bearing (45) and the bearing cone.
5/16
2020/11/26

13. Attach Tooling (B) and a suitable lifting device to main housing (39) . Position main
housing (39) on motor housing (44) . Make sure that the Duo-Cone seals are not scratched
or damaged during installation.
14. Place shims (43) in the correct position on the motor housing. If two shims were required,
put the thinner shim in contact with coupling gear (42) . Make sure that all of the holes in
the components are in alignment with each other.
6/16
2020/11/26

15. Put coupling gear (42) in the original position on the motor housing.
16. Apply Tooling (J) on the threads of bolts (41) . Install the bolts to secure coupling gear (42)
in place. Tighten bolts (41) evenly and tighten the bolts in diagonally opposite pairs.
Tighten bolts to a torque of 1600 ± 200 N·m (1180 ± 148 lb ft).
17. Install O-ring seal (40) in the main housing.
18. Thoroughly clean the mating surface of main housing (39) that contacts ring gear (38) .
Apply a bead of Tooling (K) on the mating surface of ring gear (38) . Use Tooling (B) and a
suitable lifting device. Place the ring gear in position on the main housing. Make sure that
the alignment mark on the main housing and the ring gear line up with each other. It may be
necessary to use a soft faced hammer to seat the ring gear on the main housing.
19. Assemble carrier assembly (29) , as follows:
7/16
2020/11/26

a. Apply clean SAE 30 oil on bearings (34) and (36) . Install bearings (34) and (36) in
planetary gear (35) .
b. Install thrust washers (33) and (37) on each side of the planetary gear.
c. Install the planetary gear and thrust washers in carrier assembly (29) .
d. Install planetary shaft (30) in carrier (29) and through planetary gear assembly (32) .
Make sure that the spring pin hole in the planetary shaft is in alignment with the
spring pin hole in the carrier.
8/16
2020/11/26

e. Install spring pin (31) in the carrier and into the planetary shaft. Make sure that the
spring pin hole in the planetary shaft is in alignment with the spring pin hole in the
carrier.
f. Orient the split in the spring pin (31) horizontally to the carrier. Align the split in the
spring pin to the left or to the right. Make a stake mark on each side of the spring pin
hole in the carrier. This will prevent the spring pin from falling out of the spring pin
hole. Each stake mark should be approximately 1.5 mm (0.06 inch) to 3.00 mm
(0.118 inch) from the outside diameter of the spring pin hole.
g. Repeat Steps 19.a through 19.f in order to install the remaining planetary gears in
carrier (29) .
20. Attach Tooling (B) and a suitable lifting device to carrier assembly (29) . Put the carrier
assembly in position in the ring gear. It may be necessary to move the carrier assembly back
and forth during installation in order to ensure that all gears engage properly.
9/16
2020/11/26

21. Install spacer (28) on carrier assembly (29) .
a. Apply clean SAE 30 oil on bearing (23) . Install bearing (23) in planetary gear (24) .
b. Install thrust washers (22) and (25) on each side of the planetary gear.
c. Install the thrust washers and the planetary gear in the carrier assembly (21) .
10/16
365B L Material Handler CTY00001-UP (MACHINE) POWERED BY 3196 Engin...
2020/11/26

d. Install planetary shaft (20) in carrier (21) and through planetary gear assembly (24) .
Make sure that the spring pin hole in the carrier is in alignment with the spring pin
hole in the planetary shaft.
e. Make sure that the spring pin (19) in the planetary shaft is in alignment with the
spring pin hole in the carrier.
11/16
2020/11/26

f. Orient the split in the spring pin (19) horizontally to the carrier. Align the split in the
spring pin to the left or to the right. Make a stake mark on each side of the spring pin
hole in the carrier. This will prevent the spring pin from falling out of the spring pin
hole. Each stake mark should be approximately 1.5 mm (0.06 inch) to 3.00 mm
(0.118 inch) from the outside diameter of the spring pin hole.
g. Repeat Steps 22.a through 22.f in order to install the remaining two planetary gears in
carrier (18) .
23. Attach Tooling (B) and a suitable lifting device to carrier assembly (18) . Position carrier
assembly (18) in ring gear (38) . Move carrier assembly (18) back and forth during the
installation in order to ensure that all gears engage properly.
12/16
2020/11/26

24. Install spacer (17) .
a. Install washers (16) and gear (15) . Use suitable Tooling to install ring (14) .
13/16
2020/11/26

b. Install bearings (12) and spacer (13) .
c. Install gears (11) .
d. Install washers (10) . Use Tooling (F) in order to install retaining ring (9) .
14/16
2020/11/26

26. Use two people to install carrier assembly (8) . The weight of the carrier assembly (8) is
approximately 24 kg (53 lb). Install sun gear (7) .
27. Install ring gear (6) into the cover. Tighten bolts (5) to a torque of 100 ± 20 N·m (74 ± 15 lb
ft). Install spacer (4) .
The weight of the cover is approximately 65 kg (143 lb).
28. Attach Tooling (G) and a suitable lifting device to cover (2) . Install bolts (3) and the
washers. Tighten bolts (3) to a torque of 1600 ± 200 N·m (1180 ± 148 lb ft).
15/16
2020/11/26

29. Install socket head bolts (1) .
End By: Install the final drives and the travel motors. Refer to Disassembly and Assembly, "Final
Drive - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Nov 26 01:07:15 UTC+0800 2020
16/16
2020/11/26

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01089053
Final Drive - Install
SMCS - 4050-012
Installation Procedure
Table 1
Required Tools
(A)
132-8223 Power Pack 1
1U-6221 Hydraulic Torque Wrench Assembly 1
132-8154 3/4 inch Square Drive Link 1
Note: The procedure to install the right hand final drive and the procedure to install the left hand
final drive is identical. The procedure that follows is for one of the final drives.
1/3
2020/11/26

1. Attach two lifting straps and a hoist to final drive (1). The approximate weight of the final
drive is 812 kg (1790 lb). It may be necessary to adjust the lifting straps for correct balance
of the final drive. Position final drive (1) on the track roller frame, as shown.
Note: The weight of the final drive must be adjusted if any other components are being
installed with the final drive.
2/3
2020/11/26

Note: Make sure that mounting holes (a) for the travel motor are aligned, as shown. This is
necessary for the correct installation of the travel motor.
2. Use 9S-3263 Thread Lock Compound on bolts (2). Install the washers and bolts (2). Use
Tooling (A) to tighten bolts (2) to a torque of 1800 ± 200 N·m (1328 ± 148 lb ft).
End By:
a. Install the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Install" in this
manual.
b. Install the final drive sprocket. Refer to Disassembly and Assembly, "Final Drive Sprocket -
Remove and Install" in this manual.
Thu Nov 26 01:08:12 UTC+0800 2020
3/3
2020/11/26

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01075995
Swivel - Remove
SMCS - 5060-011
Removal Procedure
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
At operating temperature the implement hydraulic oil tank is hot and
under pressure. Hot oil can cause burns.
To prevent possible injury, release the pressure in the implement
hydraulic system before hydraulic lines or components are disconnected
or removed.
1/4
2020/11/26

Table 1
Required Tools
(A) 138-7573 Link Bracket 2
1. Release the hydraulic system pressure.
Reference: Refer to Disassembly and Assembly, "Hydraulic System Pressure Release".
2. Put identification marks on all hose assemblies and all tube assemblies. Mark the locations
that are connected to the swivel assembly for installation purposes.
3. Disconnect hose assembly (2) from the top of the swivel assembly (5). Disconnect two hose
assemblies (4) from the top of the swivel assembly (5) .
4. Disconnect four hose assemblies (3) from the swivel assembly (5) .
5. Remove two bolts and washers that hold support (1) in position. Remove the support from
the swivel assembly.
2/4
2020/11/26

6. Remove eight bolts (6) and washers from the retainer (7). Remove retainer (7) from the
swivel assembly.
7. Remove six bolts (9) and washers from the middle cover assembly (8). Remove middle
cover assembly (8).
8. Remove six bolts (10) and washers from cover assemblies (11). Remove cover assemblies
(11) .
9. Disconnect two hose assemblies (15) from the swivel assembly.
10. Disconnect two hose assemblies (12) from the swivel assembly. Remove fitting (13) in
order to create extra clearance for removing the swivel assembly from the undercarriage of
the machine.
11. Disconnect four hose assemblies (14) from the swivel assembly.
3/4
2020/11/26

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

12. Remove five bolts (16) and the washers that secure the swivel assembly to the undercarriage
of the machine.
13. Remove two bolts from the top of the swivel assembly and install Tooling (A). Fasten
lifting straps to the link brackets and remove the swivel assembly from the machine. The
weight of the swivel assembly is 124 kg (274 lb).
Thu Nov 26 01:09:09 UTC+0800 2020
4/4
2020/11/26

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01076491
Swivel - Disassemble
SMCS - 5060-015
Disassembly Procedure
Table 1
Required Tools
(A) 1P-2420 Transmission Repair Stand 1
(B)
6V-3822 Bolt 2
1P-5546 Crossblock 1
5P-4168 Step Plate 1
5F-7366 Screw 1
Start By:
A. Remove the swivel. Refer to Disassembly and Assembly, "Swivel - Remove" in this
manual.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/3
2020/11/26

Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Thoroughly clean the outside of the swivel assembly prior to disassembly.
2. Fasten Tooling (A) to the swivel. The cover (2) for the swivel must face upward. The
weight of the swivel assembly is 124 kg (274 lb).
3. Remove six bolts (1) and cover (2) from the outside housing.
2/3
2020/11/26

Caterpillar cat 365 b l mh excavator (prefix cty) service repair manual (cty00001 and up)

More Related Content

What's hot (9)

Similar to Caterpillar cat 365 b l mh excavator (prefix cty) service repair manual (cty00001 and up) (20)

More from fjjskekdmme (20)

Recently uploaded (20)

Caterpillar cat 365 b l mh excavator (prefix cty) service repair manual (cty00001 and up)