Caterpillar cat 430 f2 backhoe loader (prefix hwg) service repair manual (hwg00001 and up)

Service Repair Manual
Models
430F2 Backhoe Loader

Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 430F2 BACKHOE LOADER HWG
Configuration: 430F2 IT Center Pivot Backhoe Loader HWG00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 Engines for Caterpillar Built Machines
Media Number -UENR4516-11 Publication Date -01/06/2015 Date Updated -29/10/2018
i05820300
Valve Mechanism Cover - Remove and Install
SMCS - 1107-010
Removal Procedure
Start By:
a. If the Clean Emission Module (CEM) is mounted on the valve mechanism cover. Removal
of the CEM will be necessary in order to access the valve mechanism cover. Refer to
Disassembly and Assembly, "Support and Mounting (CEM) - Remove and Install" for the
correct procedure.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/7430F2 IT Center Pivot Backhoe Loader HWG00001-UP (MACHINE) POWERED BY...
2019/11/14https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

Illustration 1 g02522396
1. Remove bolts (1) and bolts (4) from bracket (2) and bracket (3). Position brackets and
harness assembly away from valve mechanism cover (7).
2. Disconnect the plastic tube assembly (5) from the valve mechanism cover for the crankcase
breather. Refer to Disassembly and Assembly, "Crankcase Breather - Remove" for the
correct procedure.
3. Remove bolts (6) from valve mechanism cover (7).
4. Remove valve mechanism cover (7) from the cylinder head.
Note: Remove the valve mechanism cover vertically in order to avoid damage to the
electronic unit injectors.

5. Remove gasket (8) from valve mechanism cover (7).
Installation Procedure
NOTICE

1. Thoroughly clean all gasket surfaces of valve mechanism cover (7). Clean the gasket
surfaces of the cylinder head.
2. Inspect gasket (8) for damage. If necessary, install a new gasket (8) to valve mechanism
cover (7).
Note: Ensure that the gasket is fully seated into the groove of the valve mechanism cover.

3. Ensure that harness assemblies (10) are not in contact with rocker arms (11) or cylinder
head (9).
Note: Install the valve mechanism cover vertically in order to avoid damage to the
electronic unit injectors.
4. Position valve mechanism cover (7) onto cylinder head (9). Ensure that harness assemblies
(10) are not trapped during the assembly procedure.
5. Install bolts (6).

6. Tighten the bolts in the numerical sequence that is shown in Illustration 6. Tighten the bolts
to a torque of 22 N·m (195 lb in).
Repeat Step 6 in order to ensure correct torque.
7. Position brackets and harness assembly onto the valve mechanism cover. Install bolts (1)
and bolts (4) to bracket (2) and bracket (3).
8. Tighten bolts (1) and bolts (4) 9 N·m (79 lb in).
9. Connect the plastic tube assembly to the valve mechanism cover for the crankcase breather.
Refer to Disassembly and Assembly, "Crankcase Breather - Install" for the correct
procedure.
End By:
a. If necessary, mount the CEM on the valve mechanism cover. Refer to Disassembly and
Assembly, "Support and Mounting (CEM) - Remove and Install" for the correct procedure.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Nov 14 08:34:03 UTC+0800 2019

Shutdown SIS
Previous Screen
i05820301
Rocker Shaft and Pushrod - Remove
SMCS - 1102-011; 1208-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A(1)
9U-6198 Crankshaft Turning Tool 1
A(2)
5P-7306 Housing 1
5P-7305 Engine Turning Tool 1
B 298-5564 T40 Torx Socket 1
C 227-4389 E10 Torx Socket 1
(1)
The Crankshaft Turning Tool is used on the front pulley.
(2)
This Tool is used in the aperture for the electric starting motor.
Start By:
a. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover
- Remove and Install" for the correct procedure.
Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
NOTICE

1. Use Tooling (A) in order to rotate the crankshaft in a clockwise direction and position the crankshaft
the safe position. Refer to System Operation, Testing and Adjusting, "Position the Valve Mechanism
Before Maintenance Procedures" for the correct procedure.
2. Use Tooling (B) in order to loosen threaded inserts (2) on all rocker arms (1). Unscrew threaded
inserts (2) on all rocker arms (1) until all valves are fully closed.
Note: Ensure that ALL threaded inserts are fully unscrewed.

Sequence for tightening the bolts for the rocker shaft assembly
3. Use Tooling (C) to loosen Torx screws (5) in the reverse numerical order to the tightening sequence.
Refer to the Illustration 4.
4. Loosen Torx screws (4) from sufficiently in order to allow removal of rocker shaft assembly (6).
Note: Note Position (X) of different length Torx screws (4).
5. Remove rocker shaft assembly (5) from the cylinder head. Ensure that rocker shaft assembly (5) does
not come into contact with the electronic unit injector identification tag (7).
6. Place an identification mark on pushrods (6) in order to show the location. Remove the pushrods
from the cylinder head.
Note: Identification will ensure that the pushrods can be reinstalled in the original positions. Do not
interchange the positions of used pushrods.
7. Make a temporary mark on valve bridges (3) in order to show the location and the orientation.
Remove the valve bridges from the cylinder head.
Note: Identification will ensure that the valve bridges can be reinstalled in the original location and
the original orientation. Do not interchange the location or the orientation of used valve bridges.
Thu Nov 14 08:34:59 UTC+0800 2019

Shutdown SIS
Previous Screen
i05820302
Rocker Shaft - Disassemble
SMCS - 1102-015
Disassembly Procedure
Start By:
a. Remove the rocker shaft assembly. Refer to Disassembly and Assembly, "Rocker Shaft and
Pushrod - Remove" for the correct procedure.
NOTICE
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Make an identification mark on each rocker arm assembly in order to show the location.

Note: The components must be reinstalled in the original location. Do not interchange
components.
2. Remove the Torx screws from the rocker shaft assembly. Note position of different length
Torx screws for assembly purposes.
3. Remove retaining clip (2) from rocker shaft (6). Remove spring (3) from the rocker shaft.
4. Remove rocker arm assembly (4) for the inlet valve from rocker shaft (6). Remove rocker
arm assembly (5) for the exhaust valve from rocker shaft (6).
Note: The rocker arm assembly for the inlet valve is longer than the rocker arm assembly
for the exhaust valve.
5. Remove retaining clip (7) from rocker shaft (6). Remove spring (8) from the rocker shaft.

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

6. Remove rocker arm assembly (4) for the exhaust valve from rocker shaft (6). Remove
rocker arm assembly (5) for the inlet valve from rocker shaft (6).
7. Repeat Step 5 through Step 6 in order to remove the remaining rocker arms from rocker
shaft (6).
8. If necessary, follow Step 8.a through Step 8.b in order to remove threaded inserts (1) from
the rocker arms.
a. Make a temporary identification mark on each threaded inserts (1) in order to show
the location.
components.
b. Remove threaded inserts (1) from the rocker arms.
Thu Nov 14 08:35:56 UTC+0800 2019

Shutdown SIS
Previous Screen
i05820303
Rocker Shaft - Assemble
SMCS - 1102-016
Assembly Procedure
NOTICE
1. Ensure that all components are clean and free from wear and damage. Refer to
Specifications, "Rocker Shaft" for more information. If necessary, replace any components
that are worn or damaged.

2. If necessary, loosely install threaded inserts (1) to rocker arm assembly (4) and rocker arm
assembly (5).
components.
3. Lubricate the bores of rocker arm assembly (4) for the inlet valve and rocker arm assembly
(5) for the exhaust valve and rocker shaft (6) with clean engine oil.
4. Install retaining clip (2) and spring (3) to the front end of rocker shaft (6).
5. Install rocker arm assembly (4) for number one inlet valve to the rocker shaft. Install rocker
arm assembly (5) for number one exhaust valve to rocker shaft (6).
for the exhaust valve. Used components should be installed in the original location.

Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
6. Install retaining clip (7) to rocker shaft (6).
7. Install spring (8) to rocker shaft (6).
8. Install rocker arm assembly (4) for number two inlet valve to the rocker shaft. Install rocker
arm assembly (5) for number two exhaust valve to rocker shaft (6).
for the exhaust valve. Used components should be installed in the original location.
9. Repeat Step 6 through Step 8 in order to assemble the remaining components to rocker shaft
(6).
10. Install the Torx screws to the rocker shaft assembly. Ensure that the different length Torx
screws is installed into the correct position.
End By:
a. Install the rocker shaft assembly. Refer to Disassembly and Assembly, "Rocker Shaft and
Pushrod - Install" for the correct procedure.
Thu Nov 14 08:36:53 UTC+0800 2019

Caterpillar cat 430 f2 backhoe loader (prefix hwg) service repair manual (hwg00001 and up)

More Related Content

What's hot (15)

Similar to Caterpillar cat 430 f2 backhoe loader (prefix hwg) service repair manual (hwg00001 and up) (20)

More from fjsekksmem (20)

Recently uploaded (20)

Caterpillar cat 430 f2 backhoe loader (prefix hwg) service repair manual (hwg00001 and up)