2001 sea doo gts service repair manual

2001
Shop Manual
GS, GTS, GTI, GTX, GTX RFI,
GTX DI, XP, RX, RX DI

SMR2001_001_00A2.FM I
SECTION SUBSECTION PAGE
SAFETY NOTICE.................................................................................................................................. III
WHAT’S NEW ....................................................................................................................................... IV
INTRODUCTION ................................................................................................................................... VI
01 SERVICE TOOLS
AND PRODUCTS
01 - Table of contents ...................................................................... 01-01-1
02 - Mandatory service tools............................................................ 01-02-1
03 - Optional service tools................................................................ 01-03-1
04 - Service products ....................................................................... 01-04-1
02 MAINTENANCE 01 - Table of contents ...................................................................... 02-01-1
02 - Periodic inspection chart........................................................... 02-02-1
03 - Flushing and lubrication............................................................. 02-03-1
04 - Water-flooded engine................................................................ 02-04-1
05 - Storage...................................................................................... 02-05-1
03 TROUBLESHOOTING 01 - Troubleshooting chart ............................................................... 03-01-1
04 ENGINE 01 - Table of contents ...................................................................... 04-01-1
02 - Leak test ................................................................................... 04-02-1
03 - Removal and installation ........................................................... 04-03-1
04 - Magneto system....................................................................... 04-04-1
05 - Top end ..................................................................................... 04-05-1
06 - Bottom end ............................................................................... 04-06-1
07 - Rotary valve............................................................................... 04-07-1
08 - Exhaust system......................................................................... 04-08-1
05 ENGINE
MANAGEMENT (RFI)
02 - Overview................................................................................... 05-02-1
03 - Diagnostic procedures .............................................................. 05-03-1
04 - Component inspection.............................................................. 05-04-1
05 - Troubleshooting summary ........................................................ 05-05-1
06 - Adjustment................................................................................ 05-06-1
07 - Removal and installation ........................................................... 05-07-1
06 ENGINE
MANAGEMENT (DI)
02 - Overview................................................................................... 06-02-1
03 - Component inspection and adjustment .................................... 06-03-1
04 - Diagnostic procedures .............................................................. 06-04-1
07 COOLING SYSTEM 01 - Table of contents ...................................................................... 07-01-1
02 - Circuit, components and care ................................................... 07-02-1
08 FUEL SYSTEM 01 - Table of contents ...................................................................... 08-01-1
02 - Fuel circuit................................................................................. 08-02-1
03 - Air intake ................................................................................... 08-03-1
04 - Carburetor ................................................................................. 08-04-1
09 LUBRICATION
SYSTEM
02 - Oil injection system................................................................... 09-02-1
03 - Oil injection pump ..................................................................... 09-03-1
TABLE OF CONTENTS

II SMR2001_001_00A2.FM
10 ELECTRICAL
SYSTEM
01 - Table of contents...................................................................... 10-01-1
02 - Ignition system ......................................................................... 10-02-1
03 - Charging system....................................................................... 10-03-1
04 - Starting system......................................................................... 10-04-1
05 - Instruments and accessories.................................................... 10-05-1
06 - Digitally encoded security system (DESS)................................ 10-06-1
11 PROPULSION
SYSTEM
01 - Table of contents...................................................................... 11-01-1
02 - Jet pump................................................................................... 11-02-1
03 - Drive system............................................................................. 11-03-1
04 - Reverse system........................................................................ 11-04-1
05 - Variable trim system ................................................................. 11-05-1
12 STEERING SYSTEM 01 - Table of contents...................................................................... 12-01-1
02 - Steering system........................................................................ 12-02-1
03 - Alignment ................................................................................. 12-03-1
13 SUSPENSION 01 - Table of contents...................................................................... 13-01-1
02 - Direct action suspension .......................................................... 13-02-1
14 HULL/BODY 01 - Table of contents...................................................................... 14-01-1
02 - Adjustment and repair .............................................................. 14-02-1
15 TECHNICAL DATA 01 - GS model.................................................................................. 15-01-1
02 - GTI and GTS models................................................................. 15-02-1
03 - GTX RFI model.......................................................................... 15-03-1
04 - XP model .................................................................................. 15-04-1
05 - GTX and RX models.................................................................. 15-05-1
06 - GTX DI and RX DI models......................................................... 15-06-1
16 WIRING DIAGRAMS 01 - Wiring diagrams........................................................................ 16-01-1
TABLE OF CONTENTS

SMR2001_001_00A2.FM III
SAFETY NOTICE 0
This manual has been prepared as a guide to correctly service and repair all 2001 SEA-DOO watercraft.
See model list below.
This edition was primarily published to be used by watercraft mechanical technicians who are already
familiar with all service procedures relating to Bombardier made watercraft. Mechanical technicians
should attend training courses given by Bombardier Training Dept.
Please note that the instructions will apply only if proper hand tools and special service tools are used.
This Shop Manual uses technical terms which may be slightly different from the ones used in the Parts
Catalog.
It is understood that this manual may be translated into another language. In the event of any discrepancy,
the English version shall prevail.
The content depicts parts and/or procedures applicable to the particular product at time of writing. Service
and Warranty Bulletins may be published to update the content of this manual. Make sure to read and
understand these.
In addition, the sole purpose of the illustrations throughout the manual, is to assist identification of the
general configuration of the parts. They are not to be interpreted as technical drawings or exact replicas
of the parts.
The use of Bombardier parts is most strongly recommended when considering replacement of any com-
ponent. Dealer and/or distributor assistance should be sought in case of doubt.
The engines and the corresponding components identified in this document should not be utilized on
product(s) other than those mentioned in this document.
Torque wrench tightening specifications must be strictly adhered to. Locking devices (ex.: locking tab,
self-locking fasteners, etc.) must be installed or replaced with new ones. If the efficiency of a locking
device is impaired, it must be renewed.
This manual emphasizes particular information denoted by the wording and symbols:
CAUTION: Denotes an instruction which, if not followed, could severely damage vehicle components.
NOTE: Indicates supplementary information needed to fully complete an instruction.
Although the mere reading of such information does not eliminate the hazard, your understanding of the
information will promote its correct use. Always use common shop safety practice.
Bombardier Inc. disclaims liability for all damages and/or injuries resulting from the improper use of the
contents. We strongly recommend that any services be carried out and/or verified by a highly skilled
professional mechanic. It is understood that certain modifications may render use of the vehicle illegal
under existing federal, provincial and state regulations.
 WARNING
Identifies an instruction which, if not followed, could cause serious personal injury including
possibility of death.
SAFETY NOTICE

IV SMR2001_001_00A2.FM
WHAT’S NEW 0
THIS SECTION INDICATES PROCEDURES THAT WERE MODIFIED OR NEWLY ADDED IN THIS MANUAL.
RX, RX DI and GTX DI models have been merged with this manual.
RFI fuel injection section has been relocated in its own Engine Management section.
SERVICE TOOLS AND PRODUCTS
The following new tools have been added:
• Oil seal pusher for 787 RFI engines.
• Crankshaft protective cap for all models.
• Deutsch tool for joint connector on DI models.
• New Loctite safety solvant number.
• New Anti-seize lubricant number.
MAINTENANCE
• Updated storage procedure.
TROUBLESHOOTING
• Updated
ENGINE
• New sequence to torque tuned pipe (all models).
ENGINE MANAGEMENT (RFI)
• Added conversion chart for temperature sensors.
• Added the general part.
• Updated fault code table.
• Updated the water temperature sensor tests.
ENGINE MANAGEMENT (DI)
• Updated the conversion chart for temperature sensors.
• Added a quick air/fuel pressure test.
• Updated throttle body synchronization.
• Updated procedures for fuel injector, fuel pessure regulator and air pessure regulator available as single
spare parts.
• Updated MPEM replacement procedure.
• Updated the fuel delivery system diagnostic flow chart.
COOLING SYSTEM
• New diagram for the cooling system (all engines).
WHAT’S NEW

SMR2001_001_00A2.FM V
FUEL SYSTEM
• Updated procedure for air intake silencer removal/installation.
• Revised injector check valve pressure test on accelerator pump.
LUBRICATION SYSTEM
• Revised illustrations for oil injection pump adjustment.
ELECTRICAL SYSTEM
• Updated charging system procedure for RFI model.
PROPULSION SYSTEM
• Updated impeller chart.
• New procedure for oil inspection in jet pump.
• New procedure to remove venturi.
• New procedure to install bearings and seals in the housing.
• New tightening sequence for seal carrier of the mid bearing on the XP.
• New procedure to remove variable trim system on RX series.
HULL/BODY
• Seat adjustment for GTS/GTI/RX and RX DI.
• New drain plug.
• Tightening sequence for ride shoe.
TECHNICAL DATA
• Updated specifications for each model.
WIRING DIAGRAMS
• Added procedure to service the 30 A fuse on DI models.
• Updated wiring diagrams for each model.
WHAT’S NEW

INTRODUCTION
VI SMR2001_001_00A2.FM
INTRODUCTION 0
This Shop Manual covers the following BOMBAR-
DIER made SEA-DOO® 2001 watercraft models.
HULL IDENTIFICATION NUMBER
(H.I.N.)
It is located on footboard at the rear of watercraft.
GTS, GTI and RX Series
1. Hull Identification Number (H.I.N.)
All Other Models
TYPICAL
1. Hull Identification Number (H.I.N.)
MODELS
ENGINE
TYPE
MODEL
NUMBER
GS 717 5519
GS International 717 5518
XP 947 5531
XP International 947 5530
GTS 717 5521
GTS International 717 5520
GTI 717 5523
GTI International 717 5522
GTX (red) 947 5527
GTX International (red) 947 5526
GTX (blue) 947 5538
GTX International (blue) 947 5539
GTX RFI 787 5525
GTX RFI International 787 5524
GTX RFI (green) 787 5555
GTX RFI International
(green)
787 5553
GTX DI (blue) 947 DI 5529
GTX DI International
(blue)
947 DI 5528
GTX DI (red) 947 DI 5541
GTX DI International (red) 947 DI 5540
RX (blue) 947 5533
RX International (blue) 947 5532
RX (yellow) 947 5543
RX International (yellow) 947 5542
RX DI (blue) 947 5535
RX DI International (blue) 947 DI 5534
RX DI (yellow) 947 DI 5537
RX DI International
(yellow)
947 DI 5536
F00L2EA 1
F08L0QA 1
INTRODUCTION

INTRODUCTION
SMR2001_001_00A2.FM VII
All Models
The Hull Identification Number is composed of 12
digits:
ENGINE IDENTIFICATION
NUMBER (E.I.N.)
717 Engine
The Engine Identification Number is located on the
upper side of the magneto housing.
TYPICAL
1. Engine Identification Number (E.I.N.)
787 RFI Engine
upper crankcase on PTO side.
947 Engine
upper crankcase on MAGNETO side.
Z Z N 1 2 3 4 5 L 4 9 5
Model year
Serial
number*
F00A0CB
Month of production
Year of production
*A letter may also be used as a digit.
Manufacturer
1
F01D01A
F01D87A 1
F06D15A 1
INTRODUCTION

INTRODUCTION
VIII SMR2001_001_00A2.FM
ARRANGEMENT OF THIS
MANUAL
The manual is divided into 16 major sections:
01 SERVICE TOOLS AND PRODUCTS
02 MAINTENANCE
03 TROUBLESHOOTING
04 ENGINE
05 ENGINE MANAGEMENT (RFI)
06 ENGINE MANAGEMENT (DI)
07 COOLING SYSTEM
08 FUEL SYSTEM
09 LUBRICATION SYSTEM
10 ELECTRICAL SYSTEM
11 PROPULSION SYSTEM
12 STEERING SYSTEM
13 SUSPENSION
14 HULL/BODY
15 TECHNICAL DATA
16 WIRING DIAGRAM
Several sections are divided in various subsections.
There is a table of contents at the beginning of
many sections.
INTRODUCTION

SMR2001_001_00A2.FM IX
Subsection 04 (MAGNETO SYSTEM)
03-04-1
F01D4WS
Loctite
243
Loctite
243
Loctite
243
Loctite
243
Loctite
243
Loctite
648
145 N•m
(107 lbf•ft)
Anti-seize
lubricant
Page heading
indicates section
and subsection
detailed.
Exploded view assits
you in identifying
parts and related
positions.
TYPICAL PAGE
F01A0CS
Illustration number
for publishing
process.
Subsection title
indicates
beginning of the
subsection.
Dotted box
contains parts of
a particular
model or an
exploded view.
Page numbering system:
03: ENGINE section
04: MAGNETO SYSTEM subsection
1: First page of this subsection
Italic sub-title
above exploded
view indicate
pertaining models.
Drop represents
a liquid product
to be applied to a
surface. In this case
Loctite 243 to
screw threads.
Bold face number
indicates special
procedure
concerning this part.
INTRODUCTION

X SMR2001_001_00A2.FM
1
2
Section 06 FUEL SYSTEM
Subsection 03 (CARBURETORS)
06-03-4
Diaphragm
XP Model Only
CARBURETOR REMOVAL
Inspect parts for corrosion dammage (shaft, butterfly,
spring screw, check valve housing, etc.).
PUMP DIAPHRAGM LEAK TEST
TYPICAL
To remove carburetors from engine, proceed as fol-
lows:
Remove air vent tube support.
Unlock retaining slides holding air intake silencer base.
Remove air intake silencer base from watercraft.
Remove screws holding flame arrester base support
to cylinder head cover.
Unscrew base retaining screws then remove base from
carburetors and move to front of watercraft.
Turn the valve to OFF position.
NOTE: For fuel line removal, use pliers (P/N 295
000 054).
Disconnect pulse line from fuel pump.
Disconnect fuel fuel supply line from fuel pump.
Disconnect fuel return line.
Disconnect oil injection pump cable, throttle cable and
choke cable.
Remove screws no. 6 and lock washers no. 7 retaining
carburetors.
All Others Models
Remove 4 bolts no. 8 and lock washers no. 12 from
rotary valve cover then move carburetors and rotary
valve cover on top of engine.
NOTE: When removing rotary valve cover , pay
attention that the rotary valve stay in place, other-wise
it must be timed.
Remove carburetors from intake manifold.
Disconnect fuel bypass line between carburetors (twin
carburetors).
Remove carburetor(s) from rotary valve cover.
DISASSEMBLY AND INSPECTION
Using a suitable pump gauge tester, perform the fol-
lowing test proceeding as follows:
- Install pump gauge tester (P/N 295 000 083) on pulse
nipple.
- Pump tester until it reaches 28 kPa (4 PSI).
Diaphragm must stand pressure for 10 seconds. If
pressure drops, replace diaphragm.
F01F0XB
A
2
1
1 2
TYPICAL PAGE
Sub-title with part
name(s) from
exploded view.
“TYPICAL” mention
indicates a general
view which does not
represent full detail.
Sub-sub-title in this
case indicates that
particular procedure
for XP is finished, so
from this point, all
others models are
concerned.
Title in italic indicates a
particular procedure
concerning a model.
Service tool to be
used to perform a
certain procedure.
Title indicates main
procedure to be
carried-out.
Sub-sub-title in
capital indicates a
particular testing,
adjustment or
repair procedure.
Illustration
always follows
text it is
pertained to.
Numbers in a frame
are used to give a
sequence to be
perfomed.
Numbers are used
for description of
components.
Letters are used for
any measures.
Bold numbers in the
text refer to the parts
shown in the exploded
view at the beginning
of the subsection.
F01A0BS
INTRODUCTION

INTRODUCTION
SMR2001_001_00A2.FM XI
LIST OF ABBREVIATIONS USED
IN THIS MANUAL
GENERAL INFORMATION
The use of RIGHT and LEFT indications in the text,
always refers to driving position (when sitting on
watercraft).
1. Left (port)
2. Right (starboard)
The information and component/system descrip-
tions contained in this manual are correct at time
of writing. Bombardier Inc. however, maintains a
policy of continuous improvement of its products
without imposing upon itself any obligation to in-
stall them on products previously manufactured.
Bombardier Inc. reserves the right at any time to
discontinue or change specifications, designs,
features, models or equipment without incurring
obligation.
This Shop Manual uses technical terms which
may be different from the ones of the Parts Cata-
logs.
When ordering parts always refer to the specific
model Parts Catalogs.
ILLUSTRATIONS AND
PROCEDURES
The illustrations show the typical construction of
the different assemblies and, in all cases, may not
reproduce the full detail or exact shape of the parts
shown, however, they represent parts which have
the same or a similar function.
CAUTION: These watercraft are designed with
parts dimensioned mostly in the metric system.
Howeversomecomponentsmaybefromtheimpe-
rialsystem.When replacing fasteners, make sure to
use only those recommended by Bombardier.
DESCRIPTION
AC Alternate Current
APS Air Pressure Sensor
ATS Air Temperature Sensor
B.U.D.S.
Bombardier Utility and Diagnostic
Software
CDI Capacitor Discharge Ignition
CPS Crankshaft Position Sensor
CSI Cooling System Indicator
DC Direct Current
DESS Digitally Encoded Security System
DI Direct Injection
E.I.N. Engine Identification Number
ECU Electronic Control Unit
EPA Environmental Protection Agency (USA)
HP Horse Power
LED Light Emitting Diode
MAG Magneto
MPEM Multi-Purpose Electronic Module
MPH Mile Per Hour
MPI Multi Protocol Interface
N.A. Not Applicable
OPT Optional
P/N Part Number
PFD Personal Flotation Device
PSI Pound Per Square Inch
PTO Power Take Off
RAVE Rotax Adjustable Variable Exhaust
RFI Rotax Fuel Injection
RPM Revolution Per Minute
STD Standard
TBD To Be Determined
TDC Top Dead Center
TPS Throttle Position Sensor
VDC Volt Direct Current
VCK Vehicle Communication Kit
VDC Volt Direct Current
VTS Variable Trim System
WTS Water Temperature Sensor
F01L45B
1 2
INTRODUCTION

INTRODUCTION
XII SMR2001_001_00A2.FM
As many of the procedures in this manual are in-
terrelated, we suggest, that before undertaking
any task, you read and thoroughly understand the
entire section or subsection in which the proce-
dure is contained.
A number of procedures throughout the book re-
quire the use of special tools. Before undertaking
any procedure, be sure that you have on hand all
the tools required, or approved equivalents.
ENGINE EMISSIONS
INFORMATION
Manufacturer’s Responsibility
Beginning with 1999 model year engines, PWC
manufacturers of marine engines must determine
the exhaust emission levels for each engine horse-
power family and certify these engines with the
United States of America Environmental Protec-
tion Agency (EPA). An emissions control informa-
tion label, showing emission levels and engine
specifications, must be placed on each vehicle at
the time of manufacture.
Dealer Responsibility
When performing service on all 1999 and more re-
cent Sea-Doo watercrafts that carry an emissions
control information label, adjustments must be
kept within published factory specifications.
Replacement or repair of any emission related
component must be executed in a manner that
maintains emission levels within the prescribed
certification standards.
Dealers are not to modify the engine in any man-
ner that would alter the horsepower or allow emis-
sion levels to exceed their predetermined factory
specifications.
Exceptions include manufacturer’s prescribed
changes, such as altitude adjustments for exam-
ple.
Owner Responsibility
The owner/operator is required to have engine
maintenance performed to maintain emission lev-
els within prescribed certification standards.
The owner/operator is not to, and should not allow
anyone to modify the engine in any manner that
would alter the horsepower or allow emissions
levels to exceed their predetermined factory spec-
ifications.
EPA Emission Regulations
All new 1999 and more recent Sea-Doo water-
crafts manufactured by Bombardier are certified
to the EPA as conforming to the requirements of
the regulations for the control of air pollution from
new watercraft engines. This certification is con-
tingent on certain adjustments being set to factory
standards. For this reason, the factory procedure
for servicing the product must be strictly followed
and, whenever practicable, returned to the original
intent of the design.
The responsibilities listed above are general and in no
way a complete listing of the rules and regulations
pertaining to the EPA requirements on exhaust emis-
sions for marine products. For more detailed informa-
tion on this subject, you may contact the following
locations:
VIA U.S. POSTAL SERVICE:
Office of Mobile Sources
Engine Programs and Compliance Division
Engine Compliance Programs Group (6403J)
401 M St. NW
Washington, DC 20460
VIA EXPRESS or COURIER MAIL:
Office of Mobile Sources
Engine Programs and Compliance Division
Engine Compliance Programs Group (6403J)
501 3rd St. NW
Washington, DC 20001
EPA INTERNET WEB SITE:
http:/www.epa.gov/omswww
SELF-LOCKING FASTENERS
PROCEDURE
The following describes the most common appli-
cation procedures when working with self-locking
fasteners.
Use a metal brush or a screwtap to clean the hole
properly then use a solvent (Methyl-Chloride), let
act during 30 minutes and wipe off. The solvent
utilization is to ensure the adhesive works properly.
INTRODUCTION

INTRODUCTION
SMR2001_001_00A2.FM XIII
LOCTITE APPLICATION
PROCEDURE
The following describes the most common appli-
cation procedures when working with Loctite
products.
NOTE: Always use proper strength Loctite prod-
uct as recommended in this Shop Manual.
THREADLOCKER
Uncovered Holes (bolts and nuts)
1. Apply here
2. Do not apply
1. Clean threads (bolt and nut) with solvent.
2. Apply Loctite Primer N (P/N 293 800 041) on
threads and allow to dry.
3. Choose proper strength Loctite threadlocker.
4. Fit bolt in the hole.
5. Apply a few drops of threadlocker at proposed
tightened nut engagement area.
6. Position nut and tighten as required.
Blind Holes
1. On threads
2. On threads and at the bottom of hole
1. Clean threads (bolt and hole) with solvent.
threads (bolt and nut) and allow to dry for 30
seconds.
3. Choose proper strength Loctite threadlocker.
4. Apply several drops along the threaded hole and
at the bottom of the hole.
5. Apply several drops on bolt threads.
6. Tighten as required.
Stud in Blind Holes
1. On threads
2. On threads and in the hole
3. Onto nut threads
A00A3LA
1
2
A00A3MA
1
2
A00A5RA
2
1 3

INTRODUCTION
XIV SMR2001_001_00A2.FM
1. Clean threads (stud and hole) with solvent.
threads and allow to dry.
3. Put several drops of proper strength Loctite
threadlocker on female threads and in hole.
4. Apply several drops of proper strength Loctite
on stud threads.
5. Install stud.
6. Install cover, etc.
7. Apply drops of proper strength Loctite on un-
covered threads.
8. Tighten nuts as required.
Preassembled Parts
1. Apply here
2. Do not apply
1. Clean bolts and nuts with solvent.
2. Assemble components.
3. Tighten nuts.
4. Apply drops of proper strength Loctite on bolt/nut
contact surfaces.
5. Avoid touching metal with tip of flask.
NOTE: For preventive maintenance on existing
equipment, retighten nuts and apply proper strength
Loctite on bolt/nut contact surfaces.
Adjusting Screw
1. Apply here
2. Plunger
1. Adjust screw to proper setting.
2. Apply drops of proper strength Loctite thread-
locker on screw/body contact surfaces.
3. Avoid touching metal with tip of flask.
NOTE: If it is difficult to readjust, heat screw with
a soldering iron (232°C (450°F)).
STRIPPED THREAD REPAIR
Stripped Threads
1. Release agent
2. Stripped threads
3. Form-A-Thread
4. Tape
5. Cleaned bolt
6. Plate
7. New threads
8. Threadlocker
A00A3OA
1
2
A00A3PA
1
2
A00A3QA
5
8
6
7
1
2
3
4

INTRODUCTION
SMR2001_001_00A2.FM XV
Standard Thread Repair
1. Follow instructions on Loctite FORM-A-THREAD
81668 package.
2. If a plate is used to align bolt:
a. Apply release agent on mating surfaces.
b. Put waxed paper or similar film on the surfaces.
3. Twist bolt when inserting it to improve thread
conformation.
NOTE: NOT intended for engine stud repairs.
Repair of Small Holes/Fine Threads
Option 1: Enlarge damaged hole, then follow Stan-
dard Thread Repair procedure.
Option 2: Apply FORM-A-THREAD on the screw
and insert in damaged hole.
Permanent Stud Installation (light duty)
1. Use a stud or thread on desired length.
2. DO NOT apply release agent on stud.
3. Do a Standard Thread Repair.
4. Allow to cure for 30 minutes.
5. Assemble.
GASKET COMPOUND
All Parts
1. Proper strength Loctite
2. Loctite Primer N (P/N 293 800 041) and Gasket Eliminator 518
(P/N 293 800 038) on both sides of gasket
3. Loctite Primer N only
1. Remove old gasket and other contaminants
with Loctite Chisel remover (P/N 413 708 500).
Use a mechanical mean if necessary.
NOTE: Avoid grinding.
2. Clean both mating surfaces with solvent.
3. Spray Loctite Primer N on both mating surfaces
and on both sides of gasket. Allow to dry 1 or 2
minutes.
4. Apply GASKET ELIMINATOR 518 (P/N 293 800
038) on both sides of gasket, using a clean ap-
plicator.
5. Place gasket on mating surfaces and assemble
immediately.
NOTE: If the cover is bolted to blind holes (above),
apply proper strength Loctite in the hole and on
threads. Tighten.
If holes are sunken, apply proper strength Loctite
on bolt threads.
6. Tighten as usual.
MOUNTING ON SHAFT
Mounting with a Press
1. Bearing
3. Shaft
Standard
1. Clean shaft external part and element internal
part.
2. Apply a strip of proper strength Loctite on shaft
circumference at insert or engagement point.
NOTE: Retaining compound is always forced out
when applied on shaft.
3. DO NOT use anti-seize Loctite or any similar
product.
4. No curing period is required.
A00A3SA
2
1
1 3
1
A00A3UA
1
2
3

INTRODUCTION
XVI SMR2001_001_00A2.FM
Mounting in Tandem
1. Apply retaining compound on internal element
bore.
2. Continue to assemble as shown above.
CASE-IN COMPONENTS
Metallic Gaskets
1. Clean inner housing diameter and outer gasket
diameter.
2. Spray housing and gasket with Loctite Primer N
(P/N 293 800 041).
3. Apply a strip of proper strength Loctite on lead-
ing edge of outer metallic gasket diameter.
NOTE: Any Loctite product can be used here. A
low strength liquid is recommended as normal
strength and gap are required.
4. Install according to standard procedure.
5. Wipe off surplus.
6. Allow it to cure for 30 minutes.
NOTE: Normally used on worn-out housings to
prevent leaking or sliding.
It is generally not necessary to remove gasket
compound applied on outer gasket diameter.
A00A3VA 1

INTRODUCTION
SMR2001_001_00A2.FM XVII
TIGHTENING TORQUES
Tighten fasteners to torque mentioned in explod-
ed views and text. When they are not specified
refer to following table.The table also gives the
metric conversion.
N•m FASTENER SIZE (8.8) Lbf•in
1 9
2 M4 18
3 27
4 M5 35
5 44
6 53
7 62
8 71
9 80
10 M6 89
11 97
12 106
13 115
14 124
15 133
16 142
17 150
18 159
19 168
N•m FASTENER SIZE (8.8) Lbf•ft
20 15
21 15
22 16
23 M8 17
24 18
25 18
26 19
27 20
28 21
29 21
30 22
31 23
32 24
33 24
34 25
35 26
36 27
37 27
38 28
39 29
40 30
41 30
42 31
43 32
44 32
45 33
46 34
47 35
48 M10 35
49 36
50 37
51 38
52 38
53 39
54 40
55 41
56 41
57 42
58 43
59 44
60 44
61 45
62 46
63 46
64 47
65 48
66 49
67 49
68 50
69 51
70 52
71 52
72 53
73 54
74 55
75 55
76 56
77 57
78 58
79 58
80 M12 59
81 60
82 60

INTRODUCTION
XVIII SMR2001_001_00A2.FM
TIGHTENING TORQUES FOR 8.8 GRADE BOLTS AND NUTS
Technical Publications
Bombardier Inc.
Valcourt (Quebec), Canada
83 61
84 62
85 63
86 63
87 64
88 65
89 66
90 66
91 67
92 68
93 69
94 69
95 70
96 71
97 72
98 72
99 73
100 74
101 74
102 75
103 76
104 77
105 77
106 78
107 79
108 80
109 80
110 81
111 82
112 83
113 83
114 84
115 85
116 86
117 86
118 87
119 88
120 89
121 89
122 90
123 91
124 91
125 92
126 93
127 94
128 94
129 95
130 96
131 97
132 97
133 98
134 99
135 M14 100
136 100
137 101
138 102
139 103
140 103
141 104
142 105
143 105
144 106
145 107
146 108
147 108
148 109
149 110
150 111

Section 01 SERVICE TOOLS AND PRODUCTS
Subsection 01 (TABLE OF CONTENTS)
SMR2001-038_01_01ATOC.FM 01-01-1
TABLE OF CONTENTS 0
MANDATORY SERVICE TOOLS ........................................................................................... 01-02-1
ENGINE .............................................................................................................................. 01-02-1
COOLING/FUEL/OIL SYSTEMS ........................................................................................ 01-02-4
PROPULSION SYSTEM..................................................................................................... 01-02-5
WORKSHOP....................................................................................................................... 01-02-6
OPTIONAL SERVICE TOOLS ................................................................................................ 01-03-1
ENGINE .............................................................................................................................. 01-03-1
COOLING/FUEL/OIL SYSTEMS ........................................................................................ 01-03-4
PROPULSION SYSTEM..................................................................................................... 01-03-5
WATERCRAFT HANDLING................................................................................................ 01-03-6
SERVICE PRODUCTS ............................................................................................................ 01-04-1

Subsection 02 (MANDATORY SERVICE TOOLS)
SMR2001-002_01_02A.FM 01-02-1
MANDATORY SERVICE TOOLS 0
ENGINE
Degree wheel
P/N 529 035 607
A00B334
APPLICATION
717 and 787 engines.
Piston circlip installer
A) P/N 529 035 562
B) P/N 529 035 563
F06B014
APPLICATION
A) 717 and 787 engines.
B) 947 engine.
Sleeve set
A) P/N 529 035 542
(20 mm sleeve)
B) P/N 529 035 543
(21 mm sleeve)
F00B0U4
APPLICATION
B) 947 engine.
360 350 340
330
320
3
1
0
3
0
0
2
9
0
2
8
0
2
7
0
2
6
0
2
5
0
2
4
0
2
3
0
2
2
0
2
1
0
2
0
0
1
9
0
1
8
0
1
7
0
1
6
0
1
5
0
1
4
0
1
3
0
1
2
0
1
1
0
1
0
0
9
0
8
0
7
0
6
0
50
40
30 20 10
10
20
30
40
5
0
6
0
7
0
8
0
9
0
1
0
0
1
1
0
1
2
0
1
3
0
1
4
0
1
5
0
1
6
0
1
7
0
1
8
0
1
9
0
2
0
0
2
1
0
2
2
0
2
3
0
2
4
0
2
5
0
2
6
0
2
7
0
2
8
0
2
9
0
3
0
0
3
1
0
320
330
340 350 360
Air compressor ring compressor
P/N 529 035 713
F12B0L4
APPLICATION
947 DI engine.
Carbon dam guide
P/N 529 035 715
F12B0M4
APPLICATION
947 DI engine.
Carbon dam compressor
P/N 529 035 716
F12B0N4
APPLICATION
947 DI engine.
Bearing pusher
P/N 420 876 501
F00B074
APPLICATION
PTO flywheel remover/installer
P/N 295 000 001
F01J0T4
APPLICATION
717 engine.
NOTE: This tool is also used for
the impeller.
Starter drive bearing pusher
P/N 290 876 502
F06B054
APPLICATION
947 engine.
Piston pin puller
P/N 529 035 503
Expansion sleeve
P/N 295 000 117 (787 engine)
F00B0T4
APPLICATION
All engines.

01-02-2 SMR2001-002_01_02A.FM
Puller
P/N 529 035 547
A00C1A4
Puller plate
P/N 420 876 080
A00C1R4
Extension handle
P/N 295 000 125
F01D164
Screw M8 x 35 (3)
P/N 420 841 591
F00A094
Sleeve (3)
P/N 290 847 220
F00A0A4
APPLICATION
717 engine.
Puller is also used for PTO fly-
wheel on 947 engine.
Pusher
P/N 420 876 605
A00C0Y4
APPLICATION
717 engine.
Puller ass’y
P/N 290 876 488
1) Screw P/N 290 240 860
2) Hexagonal nut P/N 290 242 210
F01B0I4
APPLICATION
Alignment support plate kit
P/N 529 035 506
1) Alignment plates
A) P/N 529 035 507
B) P/N 529 035 508
2) Support
P/N 529 035 511
3) Screw (2)
P/N 207 182 544
4) Lock washer (2)
P/N 234 181 601
5) Flat washer (2)
P/N 234 081 410
F00B0F4
APPLICATION
All models.
A) 155.6 mm jet pump.
B) 139.5 mm jet pump.
Alignment shaft
P/N 295 000 141
F00B0G4
APPLICATION
All models.
2 1
Adapter
P/N 529 035 590
F00B124
APPLICATION
XP model.
VCK (Vehicle Communication Kit)
P/N 529 035 676
F12H0A4
APPLICATION
All models.
Flywheel extractor
P/N 295 000 156
F00B044
APPLICATION
XP model.

SMR2001-002_01_02A.FM 01-02-3
Engine leak tester kit
P/N 295 500 352
Pump only
P/N 529 021 800
F01B2Q5
APPLICATION
Supplementary engine leak test
kit
P/N 295 500 780
1) 787 RFI Intake plate
P/N 296 000 024
2) 947 Intake plate
P/N 296 000 025
3) 947 Rave plate
P/N 296 000 026
4) 947 Exhaust plate
P/N 296 000 027
APPLICATION
787 RFI and 947 engines.
NOTE: This kit is supplementary
to P/N 295 500 352.
Handle
P/N 420 877 650
A00C3V4
APPLICATION
Use with pushers (P/N 290 876
609 and 290 877 740).
Ring gear puller tool
P/N 420 976 235 (puller ass’y)
P/N 529 035 549 (puller bolt)
F01B294
APPLICATION
Crankshaft protective cap
A) P/N 420 876 557
B) P/N 290 877 414
F00B194
APPLICATION
B) 947 engine.
Polygonal wrench
P/N 529 035 505
F00B0Y4
APPLICATION
Exhaust system of the 947 en-
gine.
A B
Ring gear blocking tool kit
P/N 295 000 155
1) Ring gear blocking tool
P/N 295 000 134
2) Retaining plate
P/N 295 000 154
F01B265
APPLICATION
787 engine.
Rotary valve shaft pusher
P/N 290 876 609
F01B2B4
APPLICATION
787 engine.
Oil seal pusher
P/N 290 877 740
F01B2C4
APPLICATION
787 engine.
Intake plug
P/N 529 035 708
APPLICATION
947 DI engine.
1 2

01-02-4 SMR2001-002_01_02A.FM
COOLING/FUEL/OIL SYSTEMS
Gear holder
P/N 420 277 905
A00C164
APPLICATION
717 engine.
Pliers
P/N 295 000 070
Oetiker 1099
F01D174
APPLICATION
All models.
Pliers
P/N 295 000 054
Caillau
F01B1T4
APPLICATION
All models.
the propulsion system.
Fuel pressure gauge
P/N 529 035 591
F02B0B4
APPLICATION
787 RFI engine.
Fuel line disconnect tool
P/N 529 035 714
F12B0G4
APPLICATION
947 DI engine.
1. Fuel pressure gauge
P/N 529 035 709
2. Fuel pressure gauge T-fitting
P/N 529 035 710
3. Fuel pressure gauge pressure
relief valve
P/N 529 035 711
4. Fuel pressure gauge air com-
pressor adapter
P/N 529 035 712
F12R014
APPLICATION
947 DI engine.
1
3 2 4

Thank you very much
for your reading. Please
Click Here Then Get
More Information.
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

SMR2001-002_01_02A.FM 01-02-5
PROPULSION SYSTEM
Impeller remover/installer
P/N 295 000 001
F01J0T4
APPLICATION
All models.
the PTO flywheel (on some mod-
els).
Pliers
P/N 295 000 069
Oetiker 1090
F01D184
APPLICATION
All models.
Impeller shaft holder
P/N 295 000 082
F01B0W4
APPLICATION
All models.
Jet pump bearing remover
P/N 295 000 144
F01J114
APPLICATION
All models.
Bearing/seal installer
P/N 295 000 107
F01J4K4
APPLICATION
All models except GTX and XP.
Inner seal installer
P/N 529 035 609
F08B014
APPLICATION
155.6 mm (6-1/8 in) jet pump.
Impeller shaft guide
P/N 295 000 002
F01J1O4
APPLICATION
All models.
Pliers
P/N 295 000 054
Caillau
F01B1T4
APPLICATION
All models.
the fuel system.
VTS tool
P/N 295 000 133
F01B2P4
APPLICATION
XP models.
Drive shaft alignment tool
P/N 529 035 590
F08B024
APPLICATION
XP model.

01-02-6 SMR2001-002_01_02A.FM
WORKSHOP
Tool board
P/N 295 500 608
F00A0S4
APPLICATION
All models.
01
®

Subsection 03 (OPTIONAL SERVICE TOOLS)
SMR2001-002_01_03A.FM 01-03-1
OPTIONAL SERVICE TOOLS 0
ENGINE
Coil centering tool
P/N 420 876 922
A01B1V4
APPLICATION
717 engine.
Cylinder aligning tool
P/N 420 876 904
A00B084
APPLICATION
717 engine.
Distance gauge
A) P/N 529 034 800,
14 mm (.551 in)
B) P/N 529 034 900,
15.4 mm (.606 in)
C) P/N 529 035 100,
11.5 mm (.453 in)
D) P/N 529 035 000,
7.5 mm (.295 in)
F01B0H4
APPLICATION
A) 717 engine.
B) 787 engine.
C) 947 engine (MAG).
D) 947 engine (PTO).
Stroboscopic timing light
P/N 529 031 900
A00B4F4
APPLICATION
All models.
A) Four-pin magneto harness
P/N 295 000 131
B) Six-pin magneto harness
P/N 295 000 136
F01B284
APPLICATION
A) 717 engine.
B) 787 and 947 engines.
Dial indicator (TDC gauge)
P/N 295 000 143
A00B4E4
APPLICATION
All models.
Digital/induction type
tachometer
P/N 529 014 500
F01B1G4
APPLICATION
All models.
Timing mark pointer
P/N 295 000 130
F01B2O4
APPLICATION
717 engine.
Timing mark pointer
P/N 295 000 135
F01H544
APPLICATION

2001 sea doo gts service repair manual

More Related Content

More from fjskeksmemedc (20)

Recently uploaded (20)

2001 sea doo gts service repair manual