Caterpillar Cat 12M Motor Grader (Prefix B9F) Service Repair Manual (B9F00001 and up).pdf

Service Repair Manual
Models
12M Motor Grader

Shutdown SIS
Previous Screen
Product: MOTOR GRADER
Model: 12M MOTOR GRADER B9F
Configuration: 12M Motor Grader B9F00001-UP (MACHINE) POWERED BY C6.6 Engine
Disassembly and Assembly
12M and 120M Motor Graders Power Train
Media Number -KENR6419-08 Publication Date -01/05/2017 Date Updated -15/05/2017
i07077362
Transmission - Disassemble
SMCS - 3030-015; 3159-015; 3176-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 439-3940 Link Bracket 3
B 422-8733 Jack Stand Gp 3
C 1U-9202 Lever Puller Hoist 1
D 1P-1863 Retaining Ring Pliers 1
E 308-3470 Jack Stand Gp 2
F 140-7742 Sleeve 1
G 154-6181 Forcing Bolt 2
H FT-2769 Table 1
J 4C-8156 Lifting Fixture 1
K
1U-6410 Three Jaw Puller 1
1P-0510 Driver Gp 1
L 9U-7480 Compressing Tube 1
5P-7970 Nut 1
8T-4224 Hard Washer 1
- 1
1/45
12M Motor Grader B9F00001-UP (MACHINE) POWERED BY C6.6 Engine(SEBP4...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

Bolt
M8 - 1.25 by 460mm
M 8B-7548 Push-Puller Tool Gp 1
N 2P-8312 Retaining Ring Pliers 1
P
1P-2321 Combination Puller 1
1P-0510 Driver Gp 1
R
189-0408 Shackle As 1
3E-3882 Eyebolt 1
S
126-7175 Push-Puller Tool Gp 1
4C-5653 Threaded Adapter 1
1P-0510 Driver Gp 1
Start By:
a. Remove the transmission.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Put identification marks on all harness assemblies for installation purposes.
2/45
2021/1/11

Illustration 1 g01386565
1. Attach Tooling (A) and a suitable lifting device to transmission (1). The weight of
transmission (1) is approximately 862 kg (1900 lb). Use Tooling (A) and the suitable lifting
device to position transmission (1) onto Tooling (B). Remove hose assembly (2).
2. Remove bolts (3) to remove control module (4) and spacers (5).
3/45
2021/1/11

3. Remove yoke assembly (6).
4. Remove retaining ring (7).
5. Remove cup (8). Remove O-ring seal (9).
6. Attach Tooling (A), Tooling (C), and a suitable lifting device to transmission (1). Use
Tooling (A), Tooling (C), and the suitable lifting device to position transmission (1) onto
Tooling (B) and suitable cribbing. Position transmission (1) with the output shaft upward.
4/45
2021/1/11

Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
7. Remove bolts (10) to remove plate assembly (11).
8. Remove lip seal (12).
5/45
2021/1/11

9. Use Tooling (D) to remove retaining ring (13). Remove coned disc springs (14).
Note: Note the orientation of coned disc springs (14) for assembly purposes.
10. Remove O-ring seal (15) and piston (16).
6/45
2021/1/11

11. Remove piston seal (17). Remove piston seal (18).
12. Disconnect harness assembly (19) and harness assembly (21). Remove guard (20).
13. Remove bolts (22). Use two people to remove housing (23). The weight of housing (23) is
approximately 20 kg (45 lb).
7/45
2021/1/11

14. Remove pressure sensor (24) and the O-ring seal. Remove solenoid (25).
15. Remove O-ring seal (26), O-ring seal (27), O-ring seal (28), O-ring seal (29), and O-ring
seal (30).
16. Remove seal (31).
8/45
2021/1/11

17. Remove friction discs (32) and clutch plates (33).
Note: Note the quantity and the order of friction discs (32) and clutch plates (33) for
assembly purposes.
18. Remove O-ring seals (34) and dowels (35).
19. Remove retaining ring (36). Remove hub (37).
20. Attach Tooling (A), Tooling (C), Tooling F, and a suitable lifting device to transmission (1).
Use Tooling (A), Tooling (C), Tooling (F), and the suitable lifting device to position
transmission (1) onto Tooling (B) and Tooling (E) with the output shaft downward. The
weight of transmission (1) is approximately 862 kg (1900 lb).
9/45
2021/1/11

21. Remove bolt (38) to remove speed sensor (39) and guard (40).
22. Remove bolts (41) to remove speed sensor (42) and speed sensor (43).
23. Remove cover (44).
10/45
12M Motor Grader B9F00001-UP (MACHINE) POWERED BY C6.6 Engine(SEB...
2021/1/11

24. Remove bolts (45) to remove speed sensor (46) and speed sensor (47).
25. Attach Tooling (A), Tooling (C), and a suitable lifting device to housing (49). The weight of
housing (49) is approximately 136 kg (300 lb). Remove bolts (48).
26. Use Tooling (A), Tooling (C), and the suitable lifting device to remove housing (49).
Note: If necessary, use Tooling (G) to assist in removal of housing (49).
11/45
2021/1/11

27. Remove O-ring seal (50). Remove bolts (51) and the locks. Remove tube assembly (52) and
the O-ring seal.
28. Remove bolts (53) to remove seal carrier (54). Remove bolts (55) to remove seal carrier
(56).
29. Remove seal rings (57). Remove O-ring seals (58). Repeat this step for the remaining seal
carrier.
12/45
2021/1/11

30. Use Tooling (J) and a suitable lifting device to remove clutch assembly (59) and clutch
assembly (60). The combined weight of clutch assembly (59) and clutch assembly (60) is
approximately 163 kg (360 lb).
31. Position clutch assembly (59) and clutch assembly (60) onto Tooling (H). If necessary,
support clutch assembly (60) with suitable cribbing.
32. Remove Tooling (J) to separate clutch assembly (59) from clutch assembly (60).
33. Use Tooling (K) to remove bearing (61) and rotor (62) from clutch assembly (59).
Note: Be sure to attach Tooling (K) to gear assembly (63) to prevent damage to rotor (62).
13/45
2021/1/11

34. Remove thrust washer (64) and gear assembly (63).
Note: Note the orientation of thrust washer (64) for assembly purposes.
35. Remove bearing sleeves (65) from gear assembly (63).
36. Remove thrust washer (66).
14/45
2021/1/11

Note: Note the orientation of thrust washer (66) for assembly purposes.
37. Use Tooling (L) to compress hub assembly (67). Remove lock rings (68) and two half rings
(69) (not shown).
Note: Note the orientation of lock rings (68) and two ring halves (69) for assembly
purposes.
15/45
2021/1/11

38. Remove hub assembly (67), friction discs (70), and clutch plates (71).
Note: Note the order of friction discs (70) and clutch plates (71) for assembly purposes.
39. Remove wave spring (72) and piston (73).
40. Remove seal rings (74) and (75) from piston (73).
16/45
2021/1/11

41. Use a suitable lifting device to turn over clutch assembly (59). The weight of clutch
assembly (59) is approximately 59 kg (130 lb).
42. Use Tooling (M) to remove bearing (76). Remove thrust washer (77), thrust disc (78), and
gear assembly (79).
Note: Note the orientation of thrust disc (78) for assembly purposes.
17/45
2021/1/11

43. Remove thrust disc (80), washer (81), half rings (82), and lock rings (83).
44. Remove hub assembly (84). Remove friction discs (85) and clutch plates (86).
Note: Note the orientation of friction discs (85) and clutch plates (86) for assembly
purposes.
18/45
2021/1/11

45. Use Tooling (N) to remove retaining ring (87).
46. Remove balance piston (88). Remove seal ring (89) from balance piston (88).
47. Remove springs (90).
48. Remove piston (91). Remove seal rings (92) and (93) from piston (91).
49. Use Tooling (K) to remove inner bearing (94) from clutch assembly (60). Remove thrust
disc (95) and gear (96).
50. Remove thrust disc (97) and gear assembly (98) from clutch assembly (60).
19/45
2021/1/11

51. Remove sleeve bearing (99) from gear assembly (98).
52. Remove thrust disc (100) and washer (101) from clutch assembly (60).
20/45
2021/1/11

53. Use Tooling (L) to compress hub assembly (102). Remove lock rings (103) and two half
rings (104) (not shown).
purposes.
54. Remove hub assembly (102), friction discs (105), and clutch plates (106) from clutch
assembly (60).
purposes.
21/45
2021/1/11

55. Remove wave spring (107) and piston (108) from clutch assembly (60).
57. Use a suitable lifting device to turn over clutch assembly (60) onto Tooling (H). The weight
of clutch assembly (60) is approximately 54 kg (120 lb).
22/45
2021/1/11

58. Use Tooling (P) to remove inner bearing (111), thrust disc (112), and gear (113) from clutch
assembly (60).
59. Remove thrust disc (114) and gear assembly (115).
23/45
2021/1/11

60. Remove bearing (116) from gear assembly (115).
61. Remove thrust disc (117) and washer (118).
24/45
2021/1/11

purposes.
purposes.
25/45
2021/1/11

66. Use Tooling (P) to remove inner bearing (128) and gear (129) from input shaft assembly
(130). This is necessary at this time so that you can remove the remaining two clutch
assemblies.
67. Remove bolts (131) to remove seal carrier (132).
26/45
2021/1/11

68. Remove seal rings (133). Remove O-ring seals (134).
69. Attach Tooling (R) and a suitable lifting device to clutch assembly (135). The weight of
clutch assembly (135) is approximately 61 kg (135 lb). Use Tooling (R) and the suitable
lifting device to remove clutch assembly (135). Position clutch assembly (135) onto Tooling
(H).
27/45
2021/1/11

70. Use Tooling (P) to remove inner bearing (136), spacer (137), and gear (138) from clutch
assembly (135).
71. Remove spacer (139) and thrust disc (140) from clutch assembly (135).
72. Remove gear assembly (141), thrust disc (142), and washer (143).
73. Remove bearing (144) from gear assembly (141).
28/45
2021/1/11

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
GET MORE OTHER MANUALS https://www.aservicemanualpdf.com/
GET MORE OTHER MANUALS https://www.aservicemanualpdf.com/

purposes.
29/45
2021/1/11

purposes.
30/45
2021/1/11

78. Use a suitable lifting device to turn over clutch assembly (135) onto Tooling (H). The
weight of clutch assembly (135) is approximately 41 kg (90 lb).
79. Attach Tooling (S) to clutch assembly (135) to remove inner bearing (154). Remove thrust
race (155), thrust disc (156), thrust disc (157), and gear assembly (158).
Note: Note the orientation of thrust discs (156) and (157) for assembly purposes.
80. Remove roller bearing assembly (159) and thrust disc (160) from clutch assembly (135).
31/45
2021/1/11

Caterpillar Cat 12M Motor Grader (Prefix B9F) Service Repair Manual (B9F00001 and up).pdf

More Related Content

Similar to Caterpillar Cat 12M Motor Grader (Prefix B9F) Service Repair Manual (B9F00001 and up).pdf (20)

More from fujskemdidk8u (20)

Recently uploaded (20)

Caterpillar Cat 12M Motor Grader (Prefix B9F) Service Repair Manual (B9F00001 and up).pdf