JCB VM115 TIER Ⅲ VIBROMAX Service Repair Manual Instant Download.pdf

Copyright © 2004 JCB SERVICE. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any other means,
electronic, mechanical, photocopying or otherwise, without prior permission from JCB SERVICE.
World Class
Customer Support
9813/0700
Publication No.
Issued by JCB Technical Publications, JCB Aftermarket Training, Woodseat, Rocester, Staffordshire, ST14 5BW, England. Tel +44 1889 591300 Fax +44 1889 591400
Service Manual
VM 115 - TIER III
Service Manual - VM 115 - TIER III
Section 1 - General Information
Section 2 - Care and Safety
Section 3 - Maintenance
Section B - Body and Framework
Section C - Electrics
Section E - Hydraulics
Section F - Transmission
Section H - Steering
Section K - Engine
Section L - Vibration

1-0 1-0
9813/0700
Notes:

Page No.
Contents
1-i 1-i
Introduction
About this Manual ...................................................................................... 1-1
Machine Model and Serial Number .......................................................1-1
Using the Service Manual .....................................................................1-1
Section Numbering ................................................................................1-1
Left Side, Right Side ..............................................................................1-2
Cab/Canopy ..........................................................................................1-2
Cross References ..................................................................................1-2
Identifying Your Machine ........................................................................... 1-3
Machine Identification Plate ..................................................................1-3
Component Identification Plates ............................................................1-4
JCB Engine Identification ......................................................................1-5
Service Tools
Numerical List ............................................................................................ 1-7
Tool Detail Reference ................................................................................ 1-9
Section B - Body and Framework ..........................................................1-9
Section C - Electrics ............................................................................1-13
Section E - Hydraulics .........................................................................1-14
Torque Settings
Zinc Plated Fasteners and Dacromet Fasteners ..................................... 1-19
Introduction ..........................................................................................1-19
Bolts and Screws .................................................................................1-19
Vibromax Specific Torque Settings .......................................................... 1-23
Hydraulic Connections ............................................................................. 1-25
'O' Ring Face Seal System ..................................................................1-25
'Torque Stop' Hose System .................................................................1-28

1-1 1-1
9813/0700
Introduction
About this Manual
Machine Model and Serial Number
This manual provides information for the following
model(s) in the JCB machine range:
– VM 115 from SN 1705097 onwards.
Using the Service Manual
T11-004
This publication is designed for the benefit of JCB
Distributor Service Engineers who are receiving, or have
received, training by JCB Technical Training Department.
These personnel should have a sound knowledge of
workshop practice, safety procedures, and general
techniques associated with the maintenance and repair of
hydraulic earthmoving equipment.
The illustrations in this publication are for guidance only.
Where the machines differ, the text and/or the illustration
will specify.
General warnings in Section 2 are repeated throughout the
manual, as well as specific warnings. Read all safety
statements regularly, so you do not forget them.
Renewal of oil seals, gaskets, etc., and any component
showing obvious signs of wear or damage is expected as
a matter of course. It is expected that components will be
cleaned and lubricated where appropriate, and that any
opened hose or pipe connections will be blanked to
prevent excessive loss of hydraulic fluid and ingress of dirt.
Where a torque setting is given as a single figure it may be
varied by plus or minus 3%. Torque figures indicated are
for dry threads, hence for lubricated threads may be
reduced by one third.
The manufacturer's policy is one of continuous
improvement. The right to change the specification of the
machine without notice is reserved. No responsibility will
be accepted for discrepancies which may occur between
specifications of the machine and the descriptions
contained in this publication.
Finally, please remember above all else safety must come
first!
Section Numbering
T11-005
The manual is compiled in sections, the first three are
numbered and contain information as follows:
The remaining sections are alphabetically coded and deal
with Dismantling, Overhaul etc. of specific components, for
example:
Section contents, technical data, circuit descriptions,
operation descriptions etc. are inserted at the beginning of
each alphabetically coded section.
1 General Information - includes torque settings and
service tools.
2 Care and Safety - includes warnings and cautions
pertinent to aspects of workshop procedures etc.
3 Maintenance - includes service schedules and
recommended lubricants for all the machine.
A Attachments
B Body and Framework, etc.

Introduction
About this Manual
1-2 1-2
9813/0700
Left Side, Right Side
In this manual, 'left' A and 'right' B mean your left and right
when you are seated correctly in the machine.
Fig 1.
Cab/Canopy
T1-003_2
This manual frequently makes references to the cab. For
instance, 'do not operate the machine without a manual in
the cab'. It should be noted that these statements also
apply to canopy build machines.
Cross References
T1-004_2
In this publication, page cross references are made by
presenting the subject title printed in bold, italic and
underlined. It is preceeded by the 'go to' symbol. The
number of the page upon which the subject begins, is
indicated within the brackets. For example: K Cross
References ( T 1-2).

Introduction
Identifying Your Machine
1-3 1-3
9813/0700
Machine Identification Plate
Your machine has an identification plate mounted as
shown. K Fig 2. ( T 1-3).
The machine and engine serial numbers can help identify
exactly the type of equipment you have.
Fig 2.
Typical Product Identification Number (PIN)
1 World Manufacturer Identification (JCB)
2 Machine Type and Model (VM115 = VM115)
3 Randomly Generated Check Letter
4 Machine Serial Number (01801240)
1 2 3 4
JCB VM115 C 01801240

Introduction
1-4 1-4
9813/0700
Component Identification Plates
844210-2
Fig 3.
1 Engine serial number
2 Drum drive motor serial number
3 Steering unit serial number
4 Rear axle serial number
5 Vibration motor serial number
6 Hydraulic pump serial number
7 Axle hydraulic drive motor serial number
5
3
2
7
4
1
6

Introduction
1-5 1-5
9813/0700
JCB Engine Identification
Engine Data Plate
Each JCB Engine has an emissions legislation lable.
K Fig 4. ( T 1-5)
D021990
Fig 4.

Introduction
1-6 1-6
9813/0700
Page left intentionally blank

1-7 1-7
9813/0700
Service Tools
Numerical List
The tools listed in the table are special tools required for
carrying out the procedures described in this manual.
These tools are available from JCB Service.
Some tools are available as kits or sets, the part numbers
for parts within such kits or sets are not listed here. For full
details of all tools, including the content of kits and sets,
refer to Tool Detail Reference, Section 1.
Note: Tools other than those listed will be required. It is
expected that such general tools will be available in any
well equipped workshop or be available locally from any
good tool supplier.
Part
Number
Description See Section
- Bonded Washers - see Tool Detail Reference (Section 1) for content E
- Female Cone Blanking Caps - see Tool Detail Reference (Section 1) for content E
- Female Connectors - see Tool Detail Reference (Section 1) for content E
- Hydraulic Flow Test Equipment - see Tool Detail Reference (Section 1) for content E
- Male Adapters - BSP x BSP - see Tool Detail Reference (Section 1) for content E
- Male Adapters - BSP x NPT (USA only) - see Tool Detail Reference (Section 1) for
content
E
- Male Cone Blanking Caps - see Tool Detail Reference (Section 1) for content E
- Pressure Test Points - Adaptors - see Tool Detail Reference (Section 1) for content E
- Pressure Test Points - 'T' Adaptors - see Tool Detail Reference (Section 1) for content E
- Rivet Nut Tool - see Tool Detail Reference (Section 1) for content B
4104/1310 Hand Cleaner B
892/00253 Hydraulic Circuit Pressure Test Kit - see Tool Detail Reference (Section 1) for content E
892/00254 Hose E
892/00279 Gauge E
892/00280 Gauge E
892/00284 Digital Tachometer C
892/00285 Hyd. Oil Temperature Probe C
892/00298 Fluke Meter C
892/00346 Gauge E
892/00347 Connector E
892/00842 Glass Lifter B
892/00843 Folding Stand for Holding Glass B
892/00845 Cartridge Gun B
892/00846 Glass Extractor (Handles) B
892/00847 Nylon Spatula B

Service Tools
Numerical List
1-8 1-8
9813/0700
892/00848 Wire Starter B
892/00849 Braided Cutting Wire B
892/01246 Vibromax male to JCB female threaded adaptor E
892/01247 JCB male to Vibromax female threaded adaptor E
892/12345 Frequency and Vibration Measuring Tool E
926/15500 Rubber Spacer Blocks B
992/12300 12V Mobile Oven B
992/12400 24V Static Oven (2 Cartridge) B
992/12800 Cut-Out Knife B
992/12801 'L' Blades B
993/68100 Slide Hammer Kit - see Tool Detail Reference (Section 1) for content B
Part
Number
Description See Section

Service Tools
Tool Detail Reference
1-9 1-9
9813/0700
Section B - Body and Framework
Note: Not all service tools are illustrated.
Fig 5. 993/68100 Slide Hammer Kit
1 993/68101 Slide Hammer 7 993/68107 Bar - M20 x M20 X 800 mm
2 993/68102 End Stops 8 993/68108 Adaptor - M20 x 7/8" UNF
3 993/68103 Adaptor - M20 x 5/8" UNF 9 993/68109 Adaptor - M20 x M12
4 993/68104 Adaptor - M20 x 1" UNF 10 993/68110 Adaptor - M20 x 5/8" UNF (Shoulder)
5 993/68105 Adaptor - M20 x M20 11 993/68111 Adaptor - M20 x 1/2" UNF
6 993/68106 Adaptor - M20 x M24
Fig 6. Rivet Nut Tool
1 826/01099 M6 x 16 mm Rivet Nut
826/01101 M6 x 19 mm Rivet Nut
826/01104 M10 x 23 mm Rivet Nut
826/01105A M10 x 26 mm Rivet Nut
2 - Installation Tool available from: Bollhoff
Fastenings Ltd (www.bollhof.com)
Fig 7. 892/00842 Glass Lifter
Minimum 2 off - Essential for glass installation, 2 required
to handle large panes of glass. Ensure suction cups are
protected from damage during storage.

Service Tools
1-10 1-10
9813/0700
Fig 8. 892/00843 Folding Stand
Essential for preparing new glass prior to installation.
Fig 9. 892/00845 Cartridge Gun
Hand operated. Essential for the application of sealants,
polyurethane materials etc.
Fig 10. 892/00846 Glass Extractor (Handles)
Used with braided cutting wire to cut out broken glass.
K Fig 13. ( T 1-11).
Fig 11. 892/00847 Nylon Spatula
General tool used for smoothing sealants - also used to
re-install glass in rubber glazing because metal tools will
chip the glass edge.
Fig 12. 892/00848 Wire Starter
Used to access braided cutting wire through original
polyurethane seal. K Fig 13. ( T 1-11).

Service Tools
1-11 1-11
9813/0700
Fig 13. 892/00849 Braided Cutting Wire
Consumable heavy duty cut-out wire used with the glass
extraction tool. K Fig 10. ( T 1-10). Approx 25 m length.
Fig 14. 926/15500 Rubber Spacer Blocks
Used to provide the correct set clearance between glass
edge and cab frame. Unit quantity = 500 off.
Fig 15. 992/12300 Mobile Oven 12V
1 cartridge capacity. Required to pre-heat adhesive prior
to use. It is fitted with a male plug (703/23201) which fits
into a female socket (715/04300).
Fig 16. 992/12400 Static Oven 240V
Required to pre-heat adhesive prior to use. No plug
supplied.
Note: 110V models available upon request - contact JCB
Technical Service.
Fig 17. 992/12800 Cut-Out Knife
Used to remove broken glass.
Fig 18. 992/12801 'L' Blades
25 mm (1 in.) cut. Replacement blades for cut-out knife.
K Fig 17. ( T 1-11). Unit quantity = 5 off.

Service Tools
1-12 1-12
9813/0700
Fig 19. 4104/1310 Hand Cleaner
Special blend for the removal of polyurethane adhesives
(454g; 1 lb tub).

Service Tools
1-13 1-13
9813/0700
Section C - Electrics
Fig 20. 892/00298 Fluke Meter
Fig 21. 892/00285 Hydraulic Temperature Probe
Fig 22. 892/00284 Venture Microtach Digital
Tachometer

Service Tools
1-14 1-14
9813/0700
Section E - Hydraulics
Fig 23. Male Adaptors
Male Adapters - BSP x BSP
1606/2052 3/8 in. x 1/4 in.
1604/0003A 3/8 in. x 3/8 in.
892/00071 3/8 in. x 3/8 in. taper
1606/0004 1/2 in. x 1/4 in.
1606/0007A 1/2 in. x 3/8 in.
1604/0004A 1/2 in. x 1/2 in.
1606/0017 5/8 in. x 1/2 in.
1606/0008 3/4 in. x 3/8 in.
Male Adapters - BSP x NPT (USA only) 1606/0009 3/4 in. x 1/2 in.
816/00439 3/8 in. x 1/4 in. 1604/2055 3/4 in. x 3/4 in.
816/00440 1/2 in. x 1/4 in. 1606/0012 3/4 in. x 1 in.
816/15007A 3/8 in. x 3/8 in. 1606/0014 3/4 in. x 1.1/4 in.
816/15008 1/2 in. x 3/8 in. 1606/0015 1 in. x 1.1/4 in.
Fig 24. Pressure Test Adapters
892/00255 1/4 in. BSP x Test Point
892/00259 1 in BSP x Test Point
892/00260 1.1/4 in. BSP x Test Point
892/00261 5/8 in. UNF x Test Point
Fig 25. Pressure Test 'T' Adapters
816/55045 1/4 in. M BSP x 1/4 in. F BSP x Test Point
892/00265 1 in. M BSP x 1 in. F BSP x Test Point
892/00266 1.1/4 in. M BSP x 1.1/4 in. F BSP x Test Point
892/00267 1.1/4 in. M BSP x 1.1/2 in. F BSP x Test Point

Service Tools
1-15 1-15
9813/0700
Fig 26. 'T' Adapters
892/00047 3/8 in. BSP (A) x 1/4 in. BSP (B)
892/00048 1/2 in. BSP (A) x 1/4 in. BSP (B)
892/00049 5/8 in. BSP (A) x 1/4 in. BSP (B)
816/50043 3/4 in. BSP (A) x 1/4 in. BSP (B)
892/00051 1 in. BSP (A) x 1/4 in. BSP (B)
816/50005 1/2 in. BSP (A) x 1/2 in. BSP (B)
816/60096 3/4 in. BSP (A) x 3/4 in. BSP (B)
816/00017 1 in. BSP (A) x 1 in. BSP (B)
Fig 27. Female Blanking Caps
892/00055A 1/4 in. BSP
892/00056A 3/8 in. BSP
892/00057 1/2 in. BSP
892/00058A 5/8 in. BSP
892/00059A 3/4 in. BSP
892/00060 1 in. BSP
Fig 28. Male Cone Blanking Caps
816/90045 1/4 in. BSP
816/00189A 3/8 in. BSP
816/00190A 1/2 in. BSP
816/90022 5/8 in. BSP
816/90274 3/4 in. BSP
816/90205 1 in. BSP
Fig 29. Female Connectors
892/00074 3/8 in. BSP x 3/8 in. BSP
892/00075 1/2 in. BSP x 1/2 in. BSP
892/00076 5/8 in. BSP x 5/8 in. BSP
892/00077 3/4 in. BSP x 3/4 in. BSP
Fig 30. Bonded Washers
1406/0011 1/4 in. BSP
1406/0018 1/2 in. BSP
1406/0014 5/8 in. BSP
1406/0021 3/4 in. BSP
1406/0029 1.1/4 in. BSP

Service Tools
1-16 1-16
9813/0700
Fig 31. Flow Test Equipment
892/00268 Flow Monitoring Unit
892/00269 Sensor Head 0 - 100 l/min (0 - 22 UK gal/min)
892/00273 Sensor Head 0 - 380 l/min (0 - 85.5 UK gal/min)
892/00293 Connector Pipe
892/00270 Load Valve
1406/0021 Bonded Washer
1604/0006A Adapter 3/4 in M x 3/4 in M BSP
1612/2054 Adapter 3/4 in F x 3/4 in M BSP
1606/0015 Adapter 1.1/4 in M BSP x 1 in M BSP
892/00078 Connector 1 in F x 1 in F BSP
1604/0008 Adapter 1 in M x 1 in M BSP
1604/0008 Adapter 1 in M x 3/4 in M BSP
816/20013 Adapter 3/4 in F x 1 in M BSP
Fig 32. 892/ 00253 Hydraulic Circuit Pressure Test Kit
892/00201 Replacement Gauge 0-20 bar (0-300 lbf/in2)
892/00254 Replacement Hose
993/69800 Seal Kit for 892/00254 (can also be used with
probe 892/00706)
892/00706 Test Probe
892/00347 Connector - Hose to gauge
3
2
1

Service Tools
1-17 1-17
9813/0700
Fig 34. Adaptor (item A)
Note: In order to use JCB test hoses and gauges on JCB
Vibromax machines (and where applicable, other
manufacturers machines fitted with M16 X2mm test points)
a special adaptor A is required. For JCB Vibromax dealers
or customers that already have JCB Vibromax compatible
test hoses a `special adaptor' B (not shown) will be
required to connect to JCB test points
Fig 33. Hydraulic Circuit Test Gauges and
Connections
892/00280 Pressure Gauge 0-600 bar (0-9000 lbf/in2)
892/00279 Pressure Gauge 0-400 bar (0-6000 lbf/in2
)
892/00346 Pressure Gauge 0-70 bar (0-1000 lbf/in2
)
892/00347 Connector
892/00254 Hose
Item Part No Description Qty
A 892/01247 JCB male to Vibromax female
threaded adaptor - Connects
JCB female test hose to male
Vibromax test point
a/r
B 892/01246 Vibromax male to JCB female
threaded adaptor - Connects
Vibromax female test hose to
JCB male test point
a/r
Fig 35. 892/12345 Frequency and Vibration Measuring
Tool
Allows the service engineer to measure the frequency of
the vibrating drum (it will also measure engine speed on
any type of machinery).

Service Tools
1-18 1-18
9813/0700
Page left intentionally blank

Torque Settings
Zinc Plated Fasteners and Dacromet Fasteners
1-19 1-19
9813/0700
Torque Settings
T11-002
Introduction
Some external fasteners on JCB machines are
manufactured using an improved type of corrosion
resistant finish. This type of finish is called Dacromet and
replaces the original Zinc and Yellow Plating used on
earlier machines.
The two types of fasteners can be readily identified by
colour and part number suffix. K Table 1. Fastener Types
( T 1-19).
Table 1. Fastener Types
Note: As the Dacromet fasteners have a lower torque
setting than the Zinc and Yellow fasteners, the torque
figures used must be relevant to the type of fastener.
Note: A Dacromet bolt should not be used in conjunction
with a Zinc or Yellow plated nut, as this could change the
torque characteristics of the torque setting further. For the
same reason, a Dacromet nut should not be used with a
Zinc or Yellow plated bolt.
Note: All bolts used on JCB machines are high tensile and
must not be replaced by bolts of a lesser tensile
specification.
Note: Dacromet bolts, due to their high corrosion
resistance are used in areas where rust could occur.
Dacromet bolts are only used for external applications.
They are not used in applications such as gearbox or
engine joint seams or internal applications.
Bolts and Screws
Use the following torque setting tables only where no
torque setting is specified in the text.
Note: Dacromet fasteners are lubricated as part of the
plating process, do not lubricate.
Torque settings are given for the following conditions:
Condition 1
– Un-lubricated fasteners
– Zinc fasteners
– Yellow plated fasteners
Condition 2
– Zinc flake (Dacromet) fasteners
– Lubricated zinc and yellow plated fasteners
– Where there is a natural lubrication. For example,
cast iron components
Verbus Ripp Bolts
Fig 36.
Torque settings for these bolts are determined by the
application. Refer to the relevant procedure for the
required settings.
Fastener
Type
Colour Part No. Suffix
Zinc and
Yellow
Golden finish 'Z' (e.g. 1315/3712Z)
Dacromet Mottled silver finish 'D' (e.g. 1315/3712D)

Torque Settings
1-20 1-20
9813/0700
Table 2. Torque Settings - UNF Grade 'S' Fasteners
Table 3. Torque Settings - Metric Grade 8.8 Fasteners
Bolt Size Hexagon (A/F) Condition 1 Condition 2
in. mm in. Nm kgf m lbf ft Nm kgf m lbf ft
1/4 6.3 7/16 11.2 1.1 8.3 10.0 1.0 7.4
5/16 7.9 1/2 22.3 2.3 16.4 20.0 2.0 14.7
3/8 9.5 9/16 40.0 4.1 29.5 36.0 3.7 26.5
7/16 11.1 5/8 64.0 6.5 47.2 57.0 5.8 42.0
1/2 12.7 3/4 98.00 10.0 72.3 88.0 9.0 64.9
9/16 14.3 13/16 140.0 14.3 103.2 126.0 12.8 92.9
5/8 15.9 15/16 196.0 20.0 144.6 177.0 18.0 130.5
3/4 19.0 1 1/8 343.0 35.0 253.0 309.0 31.5 227.9
7/8 22.2 1 15/16 547.0 55.8 403.4 492.0 50.2 362.9
1 25.4 1 1/2 814.0 83.0 600.4 732.0 74.6 539.9
1 1/8 31.7 1 7/8 1181.0 120.4 871.1 1063.0 108.4 784.0
1 1/4 38.1 2 1/4 1646.0 167.8 1214.0 1481.0 151.0 1092.3
ISO Metric
Thread mm mm Nm kgf m lbf ft Nm kgf m lbf ft
M5 5 8 5.8 0.6 4.3 5.2 0.5 3.8
M6 6 10 9.9 1.0 7.3 9.0 0.9 6.6
M8 8 13 24.0 2.4 17.7 22.0 2.2 16.2
M10 10 17 47.0 4.8 34.7 43.0 4.4 31.7
M12 12 19 83.0 8.5 61.2 74.0 7.5 54.6
M16 16 24 205.0 20.9 151.2 184.0 18.8 135.7
M20 20 30 400.0 40.8 295.0 360.0 36.7 265.5
M24 24 36 690.0 70.4 508.9 621.0 63.3 458.0
M30 30 46 1372.0 139.9 1011.9 1235.0 125.9 910.9
M36 36 55 2399.0 244.6 1769.4 2159.0 220.0 1592.4

Torque Settings
1-21 1-21
9813/0700
Table 4. Metric Grade 10.9 Fasteners
Table 5. Metric Grade 12.9 Fasteners
ISO Metric
M5 5 8 8.1 0.8 6.0 7.3 0.7 5.4
M6 6 10 13.9 1.4 10.2 12.5 1.3 9.2
M8 8 13 34.0 3.5 25.0 30.0 3.0 22.1
M10 10 17 67.0 6.8 49.4 60.0 6.1 44.2
M12 12 19 116.0 11.8 85.5 104.0 10.6 76.7
M16 16 24 288.0 29.4 212.4 259.0 26.4 191.0
M20 20 30 562.0 57.3 414.5 506.0 51.6 373.2
M24 24 36 971.0 99.0 716.9 874.0 89.1 644.6
M30 30 46 1930.0 196.8 1423.5 1737.0 177.1 1281.1
M36 36 55 3374.0 344.0 2488.5 3036.0 309.6 2239.2
ISO Metric
M5 5 8 9.8 1.0 7.2 8.8 0.9 6.5
M6 6 10 16.6 1.7 12.2 15.0 1.5 11.1
M8 8 13 40.0 4.1 29.5 36.0 3.7 26.5
M10 10 17 80.0 8.1 59.0 72.0 7.3 53.1
M12 12 19 139.0 14.2 102.5 125.0 12.7 92.2
M16 16 24 345.0 35.2 254.4 311.0 31.7 229.4
M20 20 30 674.0 68.7 497.1 607.0 61.9 447.7
M24 24 36 1165.0 118.8 859.2 1048.0 106.9 773.0
M30 30 46 2316.0 236.2 1708.2 2084.0 212.5 1537.1
M36 36 55 4049.0 412.9 2986.4 3644.0 371.6 2687.7

Torque Settings
1-22 1-22
9813/0700
Table 6. Torque Settings - Rivet Nut Bolts/Screws
Table 7. Torque Settings - Internal Hexagon Headed Cap Screws (Zinc)
Bolt Size
Nm kgf m lbf ft
ISO Metric
Thread mm
M3 3 1.2 0.1 0.9
M4 4 3.0 0.3 2.0
M5 5 6.0 0.6 4.5
M6 6 10.0 1.0 7.5
M8 8 24.0 2.5 18.0
M10 10 48.0 4.9 35.5
M12 12 82.0 8.4 60.5
Bolt Size
Nm kgf m lbf ft
ISO Metric
Thread
M3 2.0 0.2 1.5
M4 6.0 0.6 4.5
M5 11.0 1.1 8.0
M6 19.0 1.9 14.0
M8 46.0 4.7 34.0
M10 91.0 9.3 67.0
M12 159.0 16.2 117.0
M16 395.0 40.0 292.0
M18 550.0 56.0 406.0
M20 770.0 79.0 568.0
M24 1332.0 136.0 983.0

Torque Settings
Vibromax Specific Torque Settings
1-23 1-23
9813/0700
Where no special torque data is specified, the following
standard torque figures should be applied.
Table 8. Standard Torque Specifications +/- 10%
Table 9. Nuts for Tubes and Hoses
GRADE 8.8 GRADE 10.9 GRADE 12.9
SIZE Nm lb/ft Nm lb/ft Nm lb/ft
5mm 5.5 4 7.5 5.5 9 6.6
6mm 9 6.6 12.5 9.2 15 11
8mm 22.5 16.5 31.5 23 36 26.5
10mm 44 32 62 45 75 55
12mm 77.5 57 110 81 130 95
14mm 120 88 170 125 210 155
16mm 190 140 265 195 320 236
18mm 260 192 365 269 435 320
20mm 370 273 520 383 620 457
22mm 500 369 700 516 840 619
24mm 640 471 900 665 1080 796
27mm 950 702 1350 996 1620 1195
30mm 1300 955 1800 1328 2160 1593
DIAMETER AND PITCH Nm lb/ft
16mm X 1.5 20 14.5
18mm X 1.5 35 26
20mmX 1.45 45 33.2
24mm X 1.5 60 44

Torque Settings
1-24 1-24
9813/0700
Table 10. Fittings, Connections and Plugs
Table 11. Flanges
10mm X 1.5 20 14.5
12mm X 1.5 35 26
14mm X 1.5 45 33.2
16mm X 1.5 60 44
18mm X 1.5 70 51
22mm X 1.5 100 73
27mm X 1.5 200 147
33mm X 1.5 280 207
42mm X 1.5 380 281
8mm X 1.5 28 21
10mm X 1.5 55 41
12mm X 1.75 90 67
14mm X 2 145 107
15mm X 2 230 170

Torque Settings
Hydraulic Connections
1-25 1-25
9813/0700
T11-003
'O' Ring Face Seal System
Adaptors Screwed into Valve Blocks
Adaptor screwed into valve blocks, seal onto an 'O' ring
which is compressed into a 45° seat machined into the
face of the tapped port.
Table 12. Torque Settings - BSP Adaptors
Table 13. Torque Settings - SAE Connections
BSP Adaptor
Size
Hexagon (A/F)
Nm kgf m lbf ft
in. mm
1/4 19.0 18.0 1.8 13.0
3/8 22.0 31.0 3.2 23.0
1/2 27.0 49.0 5.0 36.0
5/8 30.0 60.0 6.1 44.0
3/4 32.0 81.0 8.2 60.0
1 38.0 129.0 13.1 95.0
1 1/4 50.0 206.0 21.0 152.0
SAE Tube
Size
SAE Port
Thread Size
Hexagon (A/F)
Nm kgf m lbf ft
mm
4 7/16 - 20 15.9 20.0 - 28.0 2.0 - 2.8 16.5 - 18.5
6 9/16 - 18 19.1 46.0 - 54.0 4.7 - 5.5 34.0 - 40.0
8 3/4 - 16 22.2 95.0 - 105.0 9.7 - 10.7 69.0 - 77.0
10 7/8 - 14 27.0 130.0 - 140.0 13.2 - 14.3 96.0 - 104.0
12 1 1/16 - 12 31.8 190.0 - 210.0 19.4 - 21.4 141.0 - 155.0
16 1 5/16 - 12 38.1 290.0 - 310.0 29.6 - 31.6 216.0 - 230.0
20 1 5/8 47.6 280.0 - 380.0 28.5 - 38.7 210.0 - 280.0

Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading

Torque Settings
1-26 1-26
9813/0700
Hoses Screwed into Adaptors
Fig 37.
Hoses 37-B screwed into adaptors 37-A seal onto an `O'
ring 37-C which is compressed into a 45° seat machined
into the face of the adaptor port.
Note: Dimension 37-D will vary depending upon the
torque applied.
Table 14. BSP Hose - Torque Settings
BSP Hose Size Hexagon (A/F)
Nm kgf m lbf ft
in. mm
1/8 14.0 14.0 - 16.00 1.4 - 1.6 10.3 - 11.8
1/4 19.0 24.0 - 27.0 2.4 - 2.7 17.7 - 19.9
3/8 22.0 33.0 - 40.0 3.4 - 4.1 24.3 - 29.5
1/2 27.0 44.0 - 50.0 4.5 - 5.1 32.4 - 36.9
5/8 30.0 58.0 - 65.0 5.9 - 6.6 42.8 - 47.9
3/4 32.0 84.0 - 92.0 8.6 - 9.4 61.9 - 67.8
1 38.0 115.0 - 126.0 11.7 - 12.8 84.8 - 92.9
1 1/4 50.0 189.0 - 200.0 19.3 - 20.4 139.4 - 147.5
1 1/2 55.0 244.0 - 260.0 24.9 - 26.5 180.0 - 191.8

JCB VM115 TIER Ⅲ VIBROMAX Service Repair Manual Instant Download.pdf

More Related Content

Similar to JCB VM115 TIER Ⅲ VIBROMAX Service Repair Manual Instant Download.pdf (20)

More from id9sodkdkmdm (20)

Recently uploaded (20)

JCB VM115 TIER Ⅲ VIBROMAX Service Repair Manual Instant Download.pdf